Home › Engine / Hybrid System › 1NZ-FE EMISSION CONTROL › CANISTER › from 2016.09
RM19S0E _51 Engine / Hybrid System _051454 1NZ-FE EMISSION CONTROL _0248105 CANISTER A

1NZ-FE EMISSION CONTROL  CANISTER  INSTALLATION  


PROCEDURE

Hide 77169A 1.INSTALL FUEL SUCTION TUBE SET GASKET

a.

Coat a new fuel suction tube gasket with gasoline and install it to the fuel tank.


Hide 77020A 2.INSTALL FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE

a.

Pass the float of the fuel sender gauge assembly into the fuel tank.


b.

Bend up the tip of the fuel pump filter and set the fuel suction tube assembly on the fuel tank.

NOTICE:

Be careful not to bend the arm of the fuel sender gauge assembly.



Hide 77169A 3.INSTALL FUEL PUMP GAUGE RETAINER

a.
A247528

Align the tab of the fuel suction tube assembly with the groove of the fuel tank.


b.
A247515E02
0.844,0.281 1.167,0.49 false 1.302,0.656 0.813,0.708 false 0.667,0.167 0.833,0.323 0.167,0.156 10 true *a 0.625,0.625 0.792,0.781 0.167,0.156 10 true *b

Align the retainer mark (start of threads) with the start of the threads on the fuel tank, and while pressing down on the fuel suction tube assembly, install the new fuel pump gauge retainer and tighten it by hand as much as possible.

Text in Illustration
*a Start of Threads
(Fuel Tank)
*b Start of Threads
Fuel Pump Gauge Retainer)


c.

Install SST to the fuel pump gauge retainer.

SST
09808-14030  (09808-01010, 09808-01020, 09808-01030, 09808-01040, 09808-01050)

i.

Temporarily install plate and claw to the fuel pump gauge retainer.


ii.

Press claw against the rib of the fuel pump gauge retainer, and tighten bolt.


iii.

Install handle.



d.
U158084E02
2.167,1.052 2.458,0.635 false 2.552,4.188 2.667,4.333 0.115,0.146 10 false A 2.333,0.448 2.635,0.594 0.302,0.146 10 true SST

While making sure that SST does not rise up, slowly turn handle and tighten until the mark on the fuel pump gauge retainer is within range A as shown in the illustration.

NOTICE:
·

Be careful not to apply excessive downward force to SST, as this may damage the fuel pump or fuel tank.

·

Turning SST at an angle may cause it to slip off of the fuel pump gauge retainer, so be sure SST is horizontal when turning.

·

To prevent damage to parts, do not turn SST too vigorously.

·

If SST slips off of the fuel pump gauge retainer, loosen bolt and install SST again.




Hide 77701W 4.CONNECT NO. 1 CANISTER OUTLET HOSE SUB-ASSEMBLY

a.

Connect the No. 1 canister outlet hose sub-assembly to the fuel suction tube with pump and gauge.


Hide 77262 5.CONNECT NO. 2 FUEL EMISSION TUBE

a.

Connect the No. 2 fuel emission tube to the fuel suction tube with pump and gauge with the clip.


Hide 77209D 6.CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.

Connect the fuel tank main tube sub-assembly to the fuel suction tube with pump and gauge.


b.
A247494E01
0.794,1.218 0.957,1.360 0.163,0.142 10 *1 0.794,2.096 0.957,2.238 0.163,0.142 10 *1 1.263,4.134 1.426,4.276 0.163,0.142 10 *1 0.966,1.311 1.502,1.405 false 1.138,2.316 0.974,2.191 false 0.89,2.517 1.053,2.659 0.163,0.142 10 *4 1.207,2.413 1.082,2.578 false 0.974,1.896 1.137,2.038 0.163,0.142 10 *2 1.275,3.541 1.437,3.683 0.163,0.142 10 *2 2.319,3.335 2.481,3.477 0.163,0.142 10 *2 1.318,2.115 1.154,1.991 false 2.025,2.215 2.279,2.29 false 2.291,2.227 2.485,2.371 0.194,0.144 10 *3 0.548,3.464 0.708,3.606 0.159,0.142 10 *a 1.86,3.464 2.020,3.606 0.159,0.142 10 *b 1.039,3.704 1.275,3.636 false 1.085,3.984 1.236,4.422 false 1.251,3.94 1.328,4.134 false 2.388,4.201 2.551,4.343 0.163,0.142 10 *1 2.376,4.007 2.453,4.201 false 1.161,4.413 1.350,4.560 0.188,0.147 10 *c 2.457,3.509 2.645,3.656 0.188,0.147 10 *c 2.229,3.906 2.491,3.646 false 2.19,3.707 2.372,3.49 false

Install the fuel joint clip.

Text in Illustration
*1 Tube Joint Clip
*2 Fuel Tube Joint
*3 Fuel Tube
*4 Fuel Suction Plate
*a OK
*b NG
*c Rib

NOTICE:
·

Make sure there is no damage to or foreign matter on the connecting surfaces.

·

Check that the fuel tube joint is correctly and fully inserted.

·

Check that the main joint clip is above the rib of the fuel tube joint.

·

After installing the tube joint clip, make sure the fuel tube joint will not come out.

·

Do not damage any of the clips. If a clip is damaged, replace it.




Hide 58325E 7.INSTALL REAR FLOOR SERVICE HOLE COVER

a.

Connect the fuel pump connector to the fuel suction tube with pump and gauge.


b.
A247595E03
2,1.521 1.563,1.813 false 1.688,0.479 1.479,0.302 false 1.125,1.427 1.458,1.219 false 1.365,1.74 1.531,1.896 0.167,0.156 10 false *a 1.292,0.177 1.458,0.333 0.167,0.156 10 true *a 0.958,1.354 1.135,1.5 0.177,0.146 10 false *1

Apply butyl tape to the location shown in the illustration, align the matchmarks, and install the rear service hole cover.

Text in Illustration
*1 Butyl Tape
*a Mach Mark


Hide 8.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

Hide 9.ADD FUEL

Hide 11.PERFORM INITIALIZATION

a.

Perform "Inspection After Repair" after replacing a fuel pump.

Click hereEngine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>INITIALIZATION


Hide 71305A 12.INSTALL REAR SEATBACK CENTER HINGE SUB-ASSEMBLY (for 60/40 Split Seat Type)

Hide 13.INSTALL REAR SEAT ASSEMBLY LH (for 60/40 Split Seat Type)

Hide 14.INSTALL REAR SEAT ASSEMBLY RH (for 60/40 Split Seat Type)

Hide 15.INSTALL REAR SEAT ASSEMBLY (for Fold Down Seat Type)