Home › Engine / Hybrid System › 2NZ-FE ENGINE CONTROL › SFI SYSTEM › from 2016.09
RM19S0E _51 Engine / Hybrid System _051449 2NZ-FE ENGINE CONTROL _0248054 SFI SYSTEM C

2NZ-FE ENGINE CONTROL  SFI SYSTEM  P0327  Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor)  P0328  Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor)  


DESCRIPTION

A flat type knock sensor is used. Flat type knock sensors (non-resonant type) have a structure that can detect vibrations over a wide band of frequencies: between approximately 5 kHz and 15 kHz.

Knock sensors are fitted onto the engine block to detect engine knocking.

The knock sensor contains a piezoelectric element which generates a voltage when it becomes deformed.

The voltage is generated when the engine block vibrates due to knocking. The occurrence of engine knocking can be suppressed by delaying the ignition timing.

DTC No. DTC Detection Condition Trouble Area
P0327 Output voltage of knock sensor 0.5 V or less for 1 second or more
(1 trip detection logic)
·

Short in knock sensor circuit

·

Knock sensor

·

ECM


P0328 Output voltage of knock sensor 4.5 V or more for 1 second or more
(1 trip detection logic)
·

Open in knock sensor circuit

·

Knock sensor

·

ECM



HINT:

When either DTC P0327 or P0328 is stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is delayed to its maximum retardation. Fail-safe mode continues until the ignition switch is turned off.


Reference: Inspection using an oscilloscope

A357198E04
2.406,0.531 3.052,0.708 0.646,0.177 10 false 1 V/DIV. 1.135,1.896 1.896,2.094 0.76,0.198 10 false 1 ms./DIV. 2.615,0.99 3.063,1.198 0.448,0.208 10 false GND

The correct waveform is as shown.

ECM Terminal Name Between KNK1 and EKNK
Tester Range 1 V/DIV., 1 ms./DIV.
Condition Engine speed maintained at 4000 rpm after warming up engine

MONITOR DESCRIPTION

If the output voltage transmitted by the knock sensor remains low or high for more than 1 second, the ECM interprets this as a malfunction in the sensor circuit, and stores a DTC.

The monitor for DTCs P0327 and P0328 begins to run when 5 seconds have elapsed since the engine was started.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine and wait 10 seconds.

7.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

8.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P0327 or P0328.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, idle the engine for 5 minutes and check the DTC judgment result again.




WIRING DIAGRAM

A254081E03
1.198,1.656 1.5,1.813 0.302,0.156 10 false R1 1.198,1.854 2.167,2.083 0.969,0.229 10 false Knock Sensor 1.063,1.094 1.188,1.24 0.125,0.146 10 false 1 2.646,1.115 2.76,1.26 0.115,0.146 10 false 2 3.542,2.469 4.271,2.656 0.729,0.188 10 false (Shielded) 5.073,1.01 5.396,1.188 0.323,0.177 10 false 123 5.073,1.813 5.396,2 0.323,0.188 10 false 124 5.5,1.135 5.917,1.333 0.417,0.198 10 false KNK1 5.5,1.948 5.917,2.167 0.417,0.219 10 false EKNK 5.083,1.229 5.406,1.417 0.323,0.188 10 false B89 5.083,2.063 5.417,2.25 0.333,0.188 10 false B89 5.875,3.365 6.208,3.51 0.333,0.146 10 false ECM

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (KNOCK FEEDBACK VALUE)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Warm up the engine.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Knock Feedback Value.


f.

Read the value while driving the vehicle.

OK:

The value changes.


HINT:
Malfunction does not occur Knock Feedback Value changes
Malfunction occurs Knock Feedback Value does not change

The knock feedback value change can be confirmed by running the engine with a high load, for example, by activating the air conditioning system and racing the engine.




OK

NG

2.INSPECT ECM (KNK1 VOLTAGE)
2.INSPECT ECM (KNK1 VOLTAGE)
a.
U158048C01
1.567,0.876 1.723,1.057 0.156,0.181 10 1 1.791,0.876 1.947,1.057 0.156,0.181 10 2 0.542,0.73 0.749,0.885 0.207,0.154 10 R1 0.331,0.244 0.503,0.429 0.172,0.185 10 *a
*a Front view of wire harness connector
(to Knock Sensor)


Disconnect the knock sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
R1-1 - R1-2 Ignition switch ON 4.5 to 5.5 V




OK

3.INSPECT KNOCK SENSOR

NG

4.CHECK HARNESS AND CONNECTOR (ECM - KNOCK SENSOR)
3.INSPECT KNOCK SENSOR
a.

Inspect the knock sensor (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>KNOCK SENSOR>INSPECTION).

HINT:

Perform "Inspection After Repair" after replacing the knock sensor (See pageEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

NG

4.CHECK HARNESS AND CONNECTOR (ECM - KNOCK SENSOR)
a.

Disconnect the R1 knock sensor connector.


b.

Disconnect the B89 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R1-2 - B89-123 (KNK1) Always Below 1 Ω
R1-1 - B89-124 (EKNK) Always Below 1 Ω
R1-2 or B89-123 (KNK1) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR