Home › Engine / Hybrid System › 2NZ-FE ENGINE CONTROL › SFI SYSTEM › from 2016.09
RM19S0E _51 Engine / Hybrid System _051449 2NZ-FE ENGINE CONTROL _0248054 SFI SYSTEM C

2NZ-FE ENGINE CONTROL  SFI SYSTEM  P2118  Throttle Actuator Control Motor Current Range / Performance  


DESCRIPTION

The electronic throttle control system has a dedicated power supply circuit. The voltage (+BM) is monitored and when it is low (below 4 V), the ECM determines that there is a malfunction in the electronic throttle control system and cuts off the current to the throttle actuator.

When the voltage becomes unstable, the electronic throttle control system itself becomes unstable. For this reason, when the voltage is low, the current to the throttle actuator is cut. If repairs are made and the system returns to normal, turn the ignition switch off. The ECM then allows the current to flow to the throttle actuator so that it can be restarted.

HINT:

This electronic throttle control system does not use a throttle cable.


A256705E02
0.268,1.674 0.869,2.054 0.600,0.380 10 from Battery 0.815,3.515 1.886,3.708 1.070,0.193 10 Throttle Actuator 4.761,1.703 5.211,1.905 0.450,0.202 10 +BM 4.761,3.762 5.278,3.964 0.517,0.202 10 ME01 4.761,2.431 5.078,2.633 0.317,0.202 10 M+ 4.761,3.076 5.078,3.278 0.317,0.202 10 M- 5.934,2.481 6.589,3.199 0.655,0.718 10 Throttle Actuator Control Circuit 4.761,0.926 5.211,1.128 0.450,0.202 10 +B 0.142,1.009 0.993,1.396 0.851,0.387 10 from EFI MAIN Relay 5.934,0.756 6.568,1.475 0.634,0.718 10 Power Source Circuit for CPU 1.218,1.955 1.621,2.101 0.402,0.145 10 ETCS 5.582,4.288 5.933,4.458 0.350,0.170 10 ECM

DTC No. DTC Detection Condition Trouble Area
P2118 Open in electronic throttle control system power source (+BM) circuit
(1 trip detection logic)
·

Open in electronic throttle control system power source circuit

·

Battery

·

Battery terminals

·

ETCS fuse

·

ECM



MONITOR DESCRIPTION

The ECM monitors the battery supply voltage applied to the throttle actuator.

When the power supply voltage (+BM) drops below 4 V for 0.8 seconds or more, the ECM interprets this as an open in the power supply circuit (+BM). The ECM illuminates the MIL and stores the DTC.

If the malfunction is not repaired successfully, the DTC is stored 5 seconds after the engine is next started.

MONITOR STRATEGY

Required Sensors/Components Throttle actuator, Throttle valve, ETCS fuse
Frequency of Operation Continuous

TYPICAL ENABLING CONDITIONS

Battery voltage 8 V or higher
Electronic throttle actuator power ON

TYPICAL MALFUNCTION THRESHOLDS

Throttle actuator power supply voltage (+BM) Less than 4 V

COMPONENT OPERATING RANGE

Throttle actuator power supply voltage (+BM) 11 to 14 V

CONFIRMATION DRIVING PATTERN

A199315E12
0.983,0.548 1.630,0.760 0.647,0.211 10 3000 rpm 1.24,1.924 1.621,2.142 0.380,0.218 10 Idling 0.434,2.183 1.639,2.353 1.205,0.170 10 Ignition Switch ON 3.146,2.21 4.716,2.347 1.570,0.137 10 Approximately 5 seconds 3.468,2.799 4.790,2.983 1.323,0.184 10 16 seconds or more 2.015,2.309 2.218,2.539 0.202,0.230 10 [A] 6.014,3.229 6.242,3.415 0.228,0.186 10 [C] 4.603,0.413 4.830,0.599 0.228,0.186 10 [B]

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on [A].

6.

Start the engine.

7.

Slowly depress the accelerator pedal, raise the engine speed to approximately 3000 rpm over approximately 5 seconds, and then idle the engine [B].

8.

Check that 16 seconds or more have elapsed since the engine was started.

9.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].

10.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P2118.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [C] again and, if necessary, drive the vehicle for a period of time.




FAIL-SAFE

When either of these DTCs, or other DTCs relating to ETCS (Electronic Throttle Control System) malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator and the throttle valve is returned to a 6° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing in accordance with the accelerator pedal position to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.

The ECM continues operating in fail-safe mode until a pass condition is detected, and the ignition switch is then turned off.

WIRING DIAGRAM

A254092E05
0.938,4.094 1.583,4.333 0.646,0.24 10 false Battery 0.792,2.5 1.188,2.656 0.396,0.156 10 false MAIN 2.875,1.135 3.281,1.292 0.406,0.156 10 false ETCS 2.719,2.073 2.99,2.219 0.271,0.146 10 false M+ 2.729,2.677 2.979,2.833 0.25,0.156 10 false M- 3.063,2.052 3.208,2.198 0.146,0.146 10 false 2 3.063,2.677 3.177,2.813 0.115,0.135 10 false 1 2.01,3.26 2.302,3.438 0.292,0.177 10 false B29 2.01,3.427 3.188,3.708 1.177,0.281 10 false Throttle Actuator 5.49,0.99 5.833,1.167 0.344,0.177 10 false B89 5.521,0.813 5.802,1.01 0.281,0.198 10 false 29 5.823,0.885 6.146,1.042 0.323,0.156 10 false +BM 5.479,2.167 5.833,2.333 0.354,0.167 10 false B89 5.479,2.792 5.813,3 0.333,0.208 10 false B89 5.49,3.375 5.771,3.542 0.281,0.167 10 false B89 5.49,3.969 5.781,4.146 0.292,0.177 10 false B89 5.49,4.552 5.844,4.729 0.354,0.177 10 false B89 5.823,4.573 6.01,4.719 0.188,0.146 10 false E1 5.823,3.854 6.219,4.021 0.396,0.167 10 false ME01 5.823,3.375 6.25,3.583 0.427,0.208 10 false GE01 5.823,2.677 6.052,2.833 0.229,0.156 10 false M- 5.823,2.052 6.073,2.281 0.25,0.229 10 false M+ 5.521,1.979 5.76,2.156 0.24,0.177 10 false 60 5.521,2.615 5.75,2.844 0.229,0.229 10 false 30 5.531,3.188 5.771,3.344 0.24,0.156 10 false 58 5.531,3.781 5.771,4 0.24,0.219 10 false 59 5.521,4.365 5.813,4.51 0.292,0.146 10 false 16 3.927,3.104 4.656,3.292 0.729,0.188 10 false (Shielded) 6.073,5.167 6.417,5.323 0.344,0.156 10 false ECM 2.01,3.719 4.448,3.938 2.438,0.219 10 false (Throttle Body with Motor Assembly)

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (+BM VOLTAGE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / +BM Voltage.


d.

Read the value displayed on the GTS.

Result
Result Proceed to
Below 11 V or higher than 14 V A
11 to 14 V B



A

2.CHECK HARNESS AND CONNECTOR (BATTERY - ECM, ECM - BODY GROUND)

B

2.CHECK HARNESS AND CONNECTOR (BATTERY - ECM, ECM - BODY GROUND)
a.
U134133C02
1.573,1.135 1.313,1.635 true 2.531,1.188 2.448,1.708 true 2.802,0.646 2.531,1.146 true 1.208,1.667 1.552,1.833 0.344,0.167 10 false E1 0.125,0.104 0.281,0.26 0.156,0.156 10 false *a 0.979,0.594 1.354,0.802 0.375,0.208 10 false B89 2.219,1.708 2.688,1.885 0.469,0.177 10 false ME01 2.854,0.51 3.271,0.719 0.417,0.208 10 false +BM
*a Front view of wire harness
(to ECM)


Disconnect the ECM connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B89-29 (+BM) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B89-59 (ME01) - Body ground Always Below 1 Ω
B89-16 (E1) - Body ground Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR