Home › Engine / Hybrid System › 2NZ-FE ENGINE CONTROL › SFI SYSTEM › from 2016.09
RM19S0E _51 Engine / Hybrid System _051449 2NZ-FE ENGINE CONTROL _0248054 SFI SYSTEM C

2NZ-FE ENGINE CONTROL  SFI SYSTEM  P2610  ECM / PCM Internal Engine Off Timer Performance  


DTC SUMMARY

DTC No. Monitoring Item Malfunction Detection Condition Trouble Area Detection Timing Detection Logic
P2610 Soak timer (built into ECM) ECM internal malfunction (2 trip detection logic) ECM Ignition switch off 2 trip

DESCRIPTION

The soak timer operates after the ignition switch is turned off. When a certain amount of time has elapsed after turning the ignition switch off, the soak timer activates the ECM to perform malfunction checks which can only be performed after the engine is stopped. The soak timer is built into the ECM.

A256696E05
3.94,1.1 4.213,1.269 0.274,0.170 10 IG2 4.336,0.842 4.747,1.012 0.411,0.170 10 IGSW 5.606,4.273 5.971,4.443 0.364,0.170 10 ECM 4.304,3.482 4.715,3.652 0.411,0.170 10 MREL 4.504,2.67 4.749,2.840 0.245,0.170 10 +B 2.749,3.894 3.446,4.065 0.698,0.171 10 EFI MAIN 5.001,1.206 5.740,1.535 0.739,0.330 10 Soak Timer IC 5.001,2.558 5.740,2.887 0.739,0.330 10 Power Source IC 4.981,3.372 5.791,3.677 0.810,0.305 10 MAIN Relay Control IC 2.918,1.669 3.191,1.839 0.274,0.170 10 IG2 1.91,3.299 2.584,3.470 0.675,0.171 10 EFI MAIN 0.471,0.948 1.409,1.136 0.939,0.189 10 from Battery 0.471,3.179 1.409,3.368 0.939,0.189 10 from Battery 1.482,2.126 2.923,2.448 1.441,0.322 10 from Ignition or Starter Switch Assembly

MONITOR DESCRIPTION

1.

If the soak timer activates the ECM even though only a short amount of time has elapsed since the ignition switch was turned off, or if the soak timer does not activate the ECM even though a considerable amount of time has elapsed since the ignition switch was turned off, the ECM determines that the soak timer is malfunctioning, illuminates the MIL and stores this DTC the next time the ignition switch is turned to ON.

2.

While the engine is running, the ECM monitors the synchronization of the soak timer and the CPU clock. If these two are not synchronized, the ECM will interpret this as a malfunction, illuminate the MIL and store this DTC.


MONITOR STRATEGY

Required Sensors/Components (Main) ECM
Frequency of Operation

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Start the engine and warm it up.

6.

Turn the ignition switch off and wait for at least 15 seconds.

7.

Start the engine.

8.

Stop the engine and leave the vehicle for 60 minutes or more.

9.

Turn the ignition switch to ON and turn the GTS on.

10.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

11.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

13.

Input the DTC: P2610.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows NORMAL, the system is normal.




CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

DTC P2610 is stored if an internal ECM problem is detected. Diagnostic procedures are not required. ECM replacement is required.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.REPLACE ECM

NEXT

2.CHECK WHETHER DTC OUTPUT RECURS (IN ADDITION TO DTC P2610)
2.CHECK WHETHER DTC OUTPUT RECURS (IN ADDITION TO DTC P2610)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

HINT:

If no pending DTC is output, the repair has been successfully completed.




NEXT

END