Perform "Inspection After Repairs" after replacing the camshaft or camshaft timing gear assembly or fuel injector assembly or engine coolant temperature sensor or spark plug or knock sensor.
Click hereEngine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>INITIALIZATION
15104E
1.INSTALL STUD BOLT
Using "TORX" socket wrench E5, install the 4 stud bolts.
12101
2.INSTALL OIL PAN SUB-ASSEMBLY
Remove any old packing material from the contact surface.
Apply a continuous bead of seal packing (Diameter 2.0 to 3.0 mm (0.079 to 0.118 in.)) to the oil pan mating surface as shown in the illustration.
| *a | Seal Packing |
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
Install the oil pan within 3 minutes of applying seal packing.
Do not expose the seal to engine oil for at least 2 hours after the installation.
Install 2 new O-rings onto the cylinder block.
Using several steps, install and tighten the 13 bolts uniformly in the sequence shown in the illustration.
Each bolt length is as follows:
Bolt A 49 mm (1.93 in.)
Bolt B 88 mm (3.47 in.)
Bolt C 144 mm (5.67 in.)
15104
3.INSTALL OIL STRAINER SUB-ASSEMBLY
Install a new gasket and the oil strainer with the 2 nuts and the bolt.
12102A
4.INSTALL NO. 2 OIL PAN SUB-ASSEMBLY
Remove any old packing material from the contact surface.
Apply a continuous bead of seal packing (Diameter 2.5 to 3.5 mm (0.0984 to 0.1378 in.)) to the oil pan mating surface as shown in the illustration.
| *a | Seal Packing |
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
Install the oil pan within 3 minutes of applying seal packing.
Do not expose the seal to engine oil within 2 hours of installation.
Install the No. 2 oil pan with the 9 bolts and the 2 nuts.
Install the drain plug with a new gasket.
15600A
5.INSTALL OIL FILTER UNION
Using a 12 mm hexagon wrench, install the oil filter union.
15601
6.INSTALL OIL FILTER SUB-ASSEMBLY
Check and clean the oil filter installation surface.
Apply clean engine oil to the gasket of a new oil filter.
Gently screw the oil filter into place, and tighten it until the gasket comes into contact with the seat.
Using SST, tighten it an additional 3/4 turn.
When using a torque wrench, tighten it to the specified torque.
11115
7.INSTALL CYLINDER HEAD GASKET
Place a new cylinder head gasket on the cylinder block with the Lot No. stamp facing upward.
| *a | Lot. No. |
Pay attention to the mounting orientation of the cylinder head gasket.
Do not damage the cylinder gasket when installing the cylinder head onto the cylinder block.
11101
8.INSTALL CYLINDER HEAD SUB-ASSEMBLY
The cylinder head bolts are tightened in 2 successive steps.
Apply a light coat of engine oil to the bolt threads and the area beneath the bolt heads that come in contact with the plate washer.
Temporarily install the cylinder head with the 10 cylinder head bolts and 10 plate washers.
Do not drop the plate washers into the cylinder head.
Using several steps, tighten the 10 cylinder head bolts and 10 plate washers uniformly with an 8 mm bi-hexagon wrench in the sequence shown in the illustration.
Mark the front side of the cylinder head bolts with paint.
| *a | Paint Mark |
Retighten the cylinder head bolts an additional 90°, and then once more 90° as shown in the illustration.
Check that the paint mark is now at a 180° angle to the front.
11401L
9.INSTALL ENGINE REAR OIL SEAL
Apply MP grease to the lip of a new rear engine oil seal.
Keep the lip free of foreign matter.
Using SST and a hammer, tap in the rear engine oil seal until its surface is flush with the cylinder block and oil pan.
Do not tap the oil seal at an angle.
Wipe any extra grease off the crankshaft.
13050
10.INSTALL CAMSHAFT TIMING GEAR ASSEMBLY
Install the camshaft timing gear assembly onto the camshaft with the lock pin of the camshaft timing gear assembly released.
Clamp the camshaft in a vise, and confirm that it is locked.
Do not damage the camshaft.
Put the camshaft timing gear assembly and camshaft together with the straight pin of the groove.
| *1 | Straight Pin |
| *a | Groove |
Turn the camshaft timing gear assembly clockwise while pushing it gently toward the camshaft. When the pin fits into the groove, push to ensure a good fit.
Do not turn the camshaft timing gear in the retard direction (to the right).
Check that there is no clearance between the gear flange and the camshaft.
Tighten the bolt with the camshaft timing gear fixed.
Do not lock the camshaft timing gear assembly when tightening the bolt.
Release the lock pin of the camshaft timing gear assembly first, and tighten the bolt when the lock pin is locked in the most retarded position.
Tightening the bolts with the lock pin locked could cause breakage of the lock pin.
Check that the camshaft timing gear assembly can move in the retard direction (to the right) and is locked in the most retarded position.
Perform "Inspection After Repairs" after replacing the camshaft timing gear assembly.
Click hereEngine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>INITIALIZATION
13511
11.INSTALL CAMSHAFT
Apply a light coat of engine oil to the camshaft journals.
Place the camshaft on the cylinder head with the timing mark on the camshaft timing gear facing upward.
Examine the front marks and numbers and tighten the bolts in the sequence shown in the illustration.
Tighten each bolt uniformly while keeping the camshaft level.
Perform "Inspection After Repairs" after replacing the camshaft.
Click hereEngine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>INITIALIZATION
13523
12.INSTALL CAMSHAFT TIMING SPROCKET
Clamp the camshaft in a vise, and confirm that it is locked.
Do not damage the camshaft.
Align the knock pin hole the camshaft timing sprocket with the knock pin of the camshaft, and install the camshaft timing sprocket with the bolt.
13512
13.INSTALL NO. 2 CAMSHAFT
Apply a light coat of engine oil to the camshaft journals.
Place the camshaft on the cylinder head with the timing mark on the camshaft timing gear facing upward.
Examine the front marks and numbers on the No. 1 and No. 2 camshaft bearing caps and check that the order is as shown in the illustration. Then uniformly tighten the bolts, in several steps, in the sequence shown in the illustration.
| *1 | No. 1 Bearing Cap |
| *2 | No. 2 Bearing Cap |
Tighten each bolt uniformly while keeping the camshaft level.
Perform "Inspection After Repairs" after replacing the camshaft.
Click hereEngine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>INITIALIZATION
11101E
14.INSTALL CAMSHAFT POSITION SENSOR
Apply engine oil to the O-ring.
If the O-ring is damaged, replace the camshaft position sensor.
Install the camshaft position sensor with the bolt.
13506
15.INSTALL CHAIN SUB-ASSEMBLY
Make sure that all the timing marks are in the positions (TDC) shown in the illustration.
| *a | Timing Marks |
| *b | Timing Mark |
The positions of the timing marks may differ the predetermined positions due to the force of the valve spring.
Set the timing mark of the crankshaft in a position between 40 and 140° ATDC, as illustrated.
| *a | Timing Mark |
| *b | 40° to 140° ATDC |
Set the camshaft timing gear and the camshaft timing sprocket in the positions (20° ATDC) shown in the illustration.
| *a | 20° ATDC |
| *b | Timing Mark |
| *c | Timing Marks |
Set the crankshaft in the position (20° ATDC) shown in the illustration.
Install the No. 1 chain vibration damper with the 2 bolts.
Align the timing marks of the camshaft with the mark plates of the timing chain and install the timing chain.
| *a | Mark Plates |
| *b | Timing Marks |
| *c | Mark Plate |
| *d | Timing Mark |
Align the timing marks with the mark plates while turning the hexagonal service portion of the camshaft using a wrench.
13559
16.INSTALL CHAIN TENSIONER SLIPPER
Install the chain tensioner slipper.
13540
17.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY
Install the No. 1 chain tensioner assembly with the 2 bolts.
Remove the bar from the No. 1 chain tensioner assembly.
15100C
18.INSTALL OIL PUMP SEAL
Using SST and a hammer, tap in a new oil pump seal until its surface is flush with the timing chain cover.
Do not tap the oil seal at an angle.
Keep the seal lip free of foreign matter.
Apply MP grease to the oil seal lip.
15100
19.INSTALL OIL PUMP ASSEMBLY (for Oil Pump Type A)
The oil pump type A and oil pump type B listed in this section are differentiated based on the number of installation bolts for the oil pump assembly.
| Oil Pump Type | Number of Oil Pump Assembly Installation Bolts |
|---|---|
| A | 15 bolts |
| B | 16 bolts |
Install 2 new O-rings onto the 2 locations shown in the illustration.
Apply seal packing to the oil pump assembly, cylinder head sub-assembly and cylinder block sub-assembly as shown in the illustration.
Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
Remove any oil from the contact surface.
Install the oil pump assembly within 3 minutes and tighten the bolts and nut within 15 minutes of applying the seal packing.
Do not expose the seal to engine oil for at least 2 hours after the installation.
Align the keyway of the oil pump rotor with the rectangular portion of the crankshaft, and slide the oil pump into place.
Install the oil pump assembly and 2 wire harness clamp brackets with the 15 bolts and nut. Tighten the bolts and nut uniformly in several steps.
Install the mounting bracket and water pump within 15 minutes of installing the oil pump assembly.
Each bolt length is as follows.
A: 30 mm (1.181 in.)
B: 35 mm (1.378 in.)
C: 20 mm (0.787 in.)
E: 14 to 22 mm (0.551 to 0.866 in.), Double ended bolt
15100
20.INSTALL OIL PUMP ASSEMBLY (for Oil Pump Type B)
The oil pump type A and oil pump type B listed in this section are differentiated based on the number of installation bolts for the oil pump assembly.
| Oil Pump Type | Number of Oil Pump Assembly Installation Bolts |
|---|---|
| A | 15 bolts |
| B | 16 bolts |
Install 2 new O-rings onto the 2 locations shown in the illustration.
Apply seal packing to the oil pump assembly, cylinder head sub-assembly and cylinder block sub-assembly as shown in the illustration.
Water pump part Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent
Other part Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
Remove any oil from the contact surfaces.
Install the oil pump assembly within 3 minutes and tighten the bolts and nut within 15 minutes of applying seal packing.
Do not expose the seal to engine oil for at least 2 hours after the installation.
Align the keyway of the oil pump rotor with the rectangular portion of the crankshaft, and slide the oil pump into place.
Temporarily install the oil pump assembly and 2 wire harness clamp brackets with the 16 bolts and nut.
Do not apply oil to the bolt A.
Each bolt length is as follows.
A: 30 mm (1.181 in.)
B: 35 mm (1.378 in.)
C: 20 mm (0.787 in.)
E: 14 to 22 mm (0.551 to 0.866 in.), Double ended bolt
Tighten the 16 bolts and nut in the sequence shown in the illustration.
Be careful not to disturb the seal packing.
After installing the oil pump assembly, install the transverse engine engine mounting bracket within 10 minutes.
16100
21.INSTALL ENGINE WATER PUMP ASSEMBLY
Install the engine water pump and a new gasket with the 3 bolts and 2 nuts.
12315A
22.INSTALL TRANSVERSE ENGINE ENGINE MOUNTING BRACKET
Install the transverse engine engine mounting bracket with the 4 bolts.
13407
23.INSTALL CRANKSHAFT DAMPER SUB-ASSEMBLY
Align the pin hole in the crankshaft damper with the pin position and install the crankshaft damper sub-assembly.
Provisionally install the bolt.
Using SST, tighten the bolt while holding the crankshaft damper.
Check the SST installation positions when installing them, to avoid the SST fixing bolts from coming into contact with the oil pump.
16173
24.INSTALL WATER PUMP PULLEY
Using SST, install the water pump pulley with the 3 bolts.
25.INSPECT VALVE CLEARANCE
26.ADJUST VALVE CLEARANCE
11101J
27.INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
Apply a light coat of engine oil to a new O-ring, and install it onto the camshaft timing oil control valve.
Install the camshaft timing oil control valve with the bolt.
Do not twist the O-ring.
23250
28.INSTALL FUEL INJECTOR ASSEMBLY
Apply a light coat of gasoline or spindle oil to a new O-ring, then install one onto each fuel injector.
| *1 | O-Ring |
Apply a light coat of gasoline or spindle oil to the contact surfaces of the fuel delivery pipe and the O-ring of the fuel injector.
While turning the fuel injector left and right, install it onto the fuel delivery pipe.
|
Push |
|
Turn |
Do not twist the O-ring.
After installing the fuel injectors, check that they turn smoothly. If not, replace the O-ring with a new one.
Perform "Inspection After Repairs" after replacing the fuel injector assembly.
Click hereEngine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>INITIALIZATION
23291
29.INSTALL INJECTOR VIBRATION INSULATOR
Install 4 new injector vibration insulators onto the cylinder head.
23807V
30.INSTALL NO. 1 DELIVERY PIPE SPACER
Install the 2 No. 1 delivery pipe spacers onto the cylinder head.
Install the delivery pipe No. 1 spacer in the correct direction.
23807
31.INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY
Provisionally install the fuel delivery pipe with the 4 fuel injectors using the 3 bolts.
Do not drop the fuel injectors when installing the fuel delivery pipe.
Check that the fuel injectors rotate smoothly after installing the fuel delivery pipe.
Tighten the 3 bolts to the specified torque.
11201
32.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY
Install a new gasket onto the cylinder head cover.
Apply seal packing to the cylinder head, as shown in the illustration.
|
Seal Packing |
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
Remove any oil from the contact surface.
Install the cylinder head cover sub-assembly within 3 minutes of applying seal packing.
Do not start engine for at least 2 hours after the installation.
Provisionally install the cylinder head cover sub-assembly with the 9 bolts, 2 nuts and 2 seal washers.
Tighten the 9 bolts and 2 nuts in the sequence shown in the illustration.
12204
33.INSTALL VENTILATION VALVE SUB-ASSEMBLY
Install the ventilation valve onto the cylinder head cover.
11452
34.INSTALL OIL LEVEL DIPSTICK GUIDE
Apply engine oil to a new O-ring.
Install the O-ring onto the oil level dipstick guide.
Install the oil level dipstick guide with the bolt.
15100Q
35.INSTALL CRANKSHAFT POSITION SENSOR
Apply a light coat of engine oil to the O-ring.
If reusing the camshaft position sensor, be sure to inspect the O-ring.
Install the crankshaft position sensor with the bolt.
12108A
36.INSTALL OIL FILLER CAP GASKET
Install the oil filler cap gasket onto the oil filler cap.
12108
37.INSTALL OIL FILLER CAP SUB-ASSEMBLY
Install the oil filler cap onto the cylinder head cover.
16331A
38.INSTALL THERMOSTAT
Install a new gasket onto the thermostat.
Install the thermostat with the jiggle valve facing upward.
| *1 | Jiggle Valve |
The jiggle valve may be set within 10° on either side as shown in the illustration.
16321
39.INSTALL WATER INLET
Install the water inlet with radiator hose using the 2 nuts.
89422
40.INSTALL ENGINE COOLANT TEMPERATURE SENSOR
Install a new gasket onto the engine coolant temperature sensor.
Using a 19 mm socket wrench, install the engine coolant temperature sensor.
Perform "Inspection After Repairs" after replacing the engine coolant temperature sensor.
Click hereEngine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>INITIALIZATION
83530
41.INSTALL ENGINE OIL PRESSURE SWITCH ASSEMBLY
Apply adhesive to the end 2 or 3 threads of the oil pressure switch.
| *1 | Adhesive |
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
Do not start the engine for at least 1 hour after the installation.
Using a 24 mm deep socket wrench, install the oil pressure switch.
89615
42.INSTALL KNOCK SENSOR
Install the knock sensor with the nut as shown in the illustration.
Perform "Inspection After Repairs" after replacing the knock sensor.
Click hereEngine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>INITIALIZATION
19100P
43.INSTALL SPARK PLUG
Using a 16 mm spark plug wrench, install the 4 spark plugs.
Perform "Inspection After Repairs" after replacing the spark plug.
Click hereEngine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>INITIALIZATION