Home › Engine / Hybrid System › 1NZ-FE ENGINE MECHANICAL › VALVE CLEARANCE
RM19S0E _51 Engine / Hybrid System _051450 1NZ-FE ENGINE MECHANICAL _0248077 VALVE CLEARANCE N

1NZ-FE ENGINE MECHANICAL  VALVE CLEARANCE  ADJUSTMENT  


CAUTION / NOTICE / HINT

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


PROCEDURE

Hide 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 51441C 2.REMOVE ENGINE UNDER COVER RH (for Plastic Type)

Hide 3.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (for Metal Type)

Hide 12261 6.DISCONNECT VENTILATION HOSE

Hide 23820 7.DISCONNECT FUEL VAPOR FEED HOSE ASSEMBLY

Hide 11201 8.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 9.INSPECT VALVE CLEARANCE

HINT:

Inspect the valve clearance when the engine is cold.


a.

Set the No. 1 cylinder to TDC/compression.

i.
A116203E23
2.156,1.063 2.469,1.833 true 2.417,1.823 2.583,2 0.167,0.177 10 false *a

Turn the crankshaft damper and align its timing notch with the timing mark "0" of the oil pump.

Text in Illustration
*a Timing Notch


ii.
A116204E21
1.094,0.719 1.135,1.813 1.135,1.813 2.042,1.531 true 2.219,1.021 1.146,1.802 true 0.969,1.792 1.146,1.969 0.177,0.177 10 false *a

Check that both timing marks on the camshaft timing sprocket and camshaft timing gear are facing upward, as shown in the illustration.

Text in Illustration
*a Timing Marks

HINT:

If not, turn the crankshaft 1 complete revolution (360°) and align the marks as above.




b.
A116201

Check the valves indicated in the illustration.

i.

Using a feeler gauge, measure the clearance between the valve lifter and camshaft.

Valve clearance (cold):
for intake:

0.15 to 0.25 mm (0.006 to 0.010 in.)

for exhaust:

0.25 to 0.35 mm (0.010 to 0.014 in.)



ii.

Record any out-of-specification valve clearance measurements. They will be used later to determine the required replacement adjusting shim.



c.

Turn the crankshaft 1 complete revolution (360°) and align its timing notch with the timing mark "0" of the oil pump.


d.
A116202

Check the valves indicated in the illustration.

i.

Using a feeler gauge, measure the clearance between the valve lifter and camshaft.

Valve clearance (cold):
for intake:

0.15 to 0.25 mm (0.006 to 0.010 in.)

for exhaust:

0.25 to 0.35 mm (0.010 to 0.014 in.)



ii.

Record any out-of-specification valve clearance measurements. They will be used later to determine the required replacement adjusting shim.



Hide 10.ADJUST VALVE CLEARANCE

A116206E07
1.729,0.365 0.917,0.24 true 0.719,0.146 0.917,0.333 0.198,0.188 10 false *a

Text in Illustration
*a Matchmark

NOTICE:

When rotating the camshaft with the timing chain removed, rotate the crankshaft damper counterclockwise 40° from the TDC and align its timing notch with the matchmark of the timing chain cover to prevent the pistons from coming into contact with the valves.


a.

Remove the fan and generator V belt (See page Engine / Hybrid System>1NZ-FE ENGINE MECHANICAL>DRIVE BELT>REMOVAL).


b.

Remove the engine mounting insulator sub-assembly RH (See page Engine / Hybrid System>1NZ-FE LUBRICATION>OIL PUMP>REMOVAL).


c.

Set the No. 1 cylinder to TDC/compression.

i.
A116203E24
2.156,1.063 2.469,1.833 true 2.427,1.833 2.594,2.01 0.167,0.177 10 false *a

Turn the crankshaft damper and align its timing notch with the timing mark "0" of the oil pump.

Text in Illustration
*a Timing Notch


ii.
A116204E22
1.094,0.719 1.135,1.813 1.135,1.813 2.042,1.531 true 2.219,1.021 1.146,1.802 true 0.969,1.792 1.146,1.969 0.177,0.177 10 false *a

Check that both timing marks on the camshaft timing sprocket and camshaft timing gear are facing upward, as shown in the illustration.

Text in Illustration
*a Timing Marks

HINT:

If not, turn the crankshaft 1 complete revolution (360°) and align the marks as above.




d.
A116207E14
1.094,0.729 1.135,1.781 1.135,1.781 2.031,1.521 true 2.208,1.031 1.156,1.771 true 1.177,0.625 2.5,0.177 2.5,0.177 2.198,0.917 true 2.521,0.042 2.719,0.229 0.198,0.188 9 true *a 0.979,1.771 1.146,1.948 0.167,0.177 10 false *b

Place paint marks on the chain in the places where the timing marks of the camshaft timing sprocket and the camshaft timing gear are located.

Text in Illustration
*a Paint Marks
*b Timing Marks


e.
G100163

Using an 8 mm hexagon wrench, remove the screw plug.


f.
A116209E05
1.74,2.615 1.833,3.01 false 1.76,3.01 1.958,3.188 0.198,0.177 10 false *a

Insert a screwdriver into the service hole in the chain tensioner to pull the stopper plate of the chain tensioner upward.

Text in Illustration
*a Stopper Plate


g.
A116210E08
1.021,2.49 1.021,2.875 true 0.927,2.885 1.115,3.063 0.188,0.177 10 false *a

Using a wrench, rotate camshaft No. 2 clockwise to push in the plunger of the chain tensioner.

Text in Illustration
*a Plunger


h.
A116212

Remove the screwdriver from the service hole, then align the hole in the stopper plate with the service hole and insert a 3 mm (0.12 in.) diameter bar into the holes to hold the stopper plate.

HINT:
·

Fix the stopper plate using the bar while rotating the camshaft right and left slightly.

·

Hold the bar with tape so that the bar does not come off.




i.
A116213

Using a wrench, hold the hexagonal lobe of camshaft No. 2 and remove the flange bolt.


j.
A116214E02
0.896,0.74 0.896,0.448 true 1.229,0.792 1.229,0.458 true 1.667,0.802 1.667,0.458 true 2.094,0.802 2.094,0.458 true 2.531,0.792 2.531,0.458 true 0.854,0.26 1.01,0.438 0.156,0.177 10 false 1 2.5,0.26 2.656,0.438 0.156,0.177 10 false 2 1.198,0.26 1.354,0.438 0.156,0.177 10 false 3 2.063,0.26 2.219,0.438 0.156,0.177 10 false 4 1.635,0.26 1.792,0.438 0.156,0.177 10 false 5

Using several steps, loosen and remove the 11 bearing cap bolts uniformly in the sequence shown in the illustration, then remove camshaft bearing cap No. 1 and camshaft bearing cap No. 2.

NOTICE:

Loosen each bolt uniformly while keeping the camshaft level.



k.
A116215

Remove the flange bolt and the camshaft timing sprocket.


l.
A116216

Remove No. 2 camshaft.


m.
A116217E03
1.135,1.302 1.135,1.51 true 1.604,1.313 1.604,1.51 true 2.083,1.313 2.083,1.5 true 2.563,1.302 2.563,1.49 true 1.094,1.531 1.25,1.708 0.156,0.177 10 false 2 1.563,1.542 1.719,1.719 0.156,0.177 10 false 4 2.052,1.531 2.208,1.708 0.156,0.177 10 false 3 2.531,1.521 2.688,1.698 0.156,0.177 10 false 1

Using several steps, loosen and remove the 8 bearing cap bolts uniformly in the sequence shown in the illustration, then remove No. 2 camshaft bearing cap.

NOTICE:

Loosen each bolt uniformly while keeping the camshaft level.



n.
A116218

Hold the chain by hand and remove the camshaft and the camshaft timing gear assembly.


o.
A035227

Tie the chain with a piece of string as shown in the illustration.


p.

Remove the 16 valve lifters.


q.
A001082

Using a micrometer, measure the thickness of the removed lifter.


r.

Calculate the thickness of a new lifter so that the valve clearance comes to within the specified values.

A Thickness of new lifter
B Thickness of used lifter
C Measured valve clearance

Valve clearance:

Intake A = B + (C - 0.20 mm (0.008 in.))

Exhaust A = B + (C - 0.30 mm (0.012 in.))



s.

Select a new lifter with a thickness as close to the calculated values as possible.

HINT:

Lifters are available in 35 sizes in increments of 0.020 mm (0.0008 in.), from 5.060 mm (0.1992 in.) to 5.740 mm (0.2260 in.).


A117457

Intake valve clearance (cold):

0.15 to 0.25 mm (0.006 to 0.010 in.)


EXAMPLE:

A 5.250 mm (0.2067 in.) lifter is installed, and the measured clearance is 0.400 mm (0.0158 in.). Replace the 5.250 mm (0.2067 in.) lifter with a new No. 46 lifter.


New Shim Thickness:
Shim No. Thickness Shim No. Thickness Shim No. Thickness
06 5.060 (0.1992) 30 5.300 (0.2087) 54 5.540 (0.2181)
08 5.080 (0.2000) 32 5.320 (0.2094) 56 5.560 (0.2189)
10 5.100 (0.2008) 34 5.340 (0.2102) 58 5.580 (0.2197)
12 5.120 (0.2016) 36 5.360 (0.2110) 60 5.600 (0.2205)
14 5.140 (0.2024) 38 5.380 (0.2118) 62 5.620 (0.2213)
16 5.160 (0.2031) 40 5.400 (0.2126) 64 5.640 (0.2220)
18 5.180 (0.2039) 42 5.420 (0.2134) 66 5.660 (0.2228)
20 5.200 (0.2047) 44 5.440 (0.2142) 68 5.680 (0.2236)
22 5.220 (0.2055) 46 5.460 (0.2150) 70 5.700(0.2244)
24 5.240 (0.2063) 48 5.480 (0.2157) 72 5.720 (0.2252)
26 5.260 (0.2071) 50 5.500 (0.2165) 74 5.740 (0.2260)
28 5.280 (0.2079) 52 5.520 (0.2173)


A117458

Exhaust valve clearance (Cold):

0.25 to 0.35 mm (0.010 to 0.014 in.)


EXAMPLE:

A 5.340 mm (0.2102 in.) lifter is installed, and the measured clearance is 0.440 mm (0.0173 in.). Replace the 5.340 mm (0.2102 in.) lifter with a new No. 48 lifter.


New Shim Thickness:
Shim No. Thickness Shim No. Thickness Shim No. Thickness
06 5.060 (0.1992) 30 5.300 (0.2087) 54 5.540 (0.2181)
08 5.080 (0.2000) 32 5.320 (0.2094) 56 5.560 (0.2189)
10 5.100 (0.2008) 34 5.340 (0.2102) 58 5.580 (0.2197)
12 5.120 (0.2016) 36 5.360 (0.2110) 60 5.600 (0.2205)
14 5.140 (0.2024) 38 5.380 (0.2118) 62 5.620 (0.2213)
16 5.160 (0.2031) 40 5.400 (0.2126) 64 5.640 (0.2220)
18 5.180 (0.2039) 42 5.420 (0.2134) 66 5.660 (0.2228)
20 5.200 (0.2047) 44 5.440 (0.2142) 68 5.680 (0.2236)
22 5.220 (0.2055) 46 5.460 (0.2150) 70 5.700 (0.2244)
24 5.240 (0.2063) 48 5.480 (0.2157) 72 5.720 (0.2252)
26 5.260 (0.2071) 50 5.500 (0.2165) 74 5.740 (0.2260)
28 5.280 (0.2079) 52 5.520 (0.2173)



t.

Install the selected valve lifter.


u.

Apply a light coat of engine oil to the camshaft and camshaft journals.


v.
A116220E09
1.646,0.927 0.667,0.229 true 1.688,1.073 2.688,1.792 true 0.5,0.094 0.656,0.271 0.156,0.177 10 false *a 2.74,1.781 3.021,2.042 0.281,0.26 10 true *b

Install the chain onto the camshaft timing gear with the paint mark and the timing mark aligned as shown in the illustration.

Text in Illustration
*a Paint Mark
*b Timing Mark


w.
A116222E01
0.757,2.555 0.913,2.736 0.156,0.182 10 3 1.381,2.555 1.537,2.736 0.156,0.182 10 1 2.072,2.555 2.228,2.736 0.156,0.182 10 2 2.714,2.555 2.87,2.736 0.156,0.182 10 4

Examine the front marks and the numbers on No. 2 camshaft bearing cap and check that the sequence is as shown in the illustration. Then uniformly tighten the bolts in several steps in the sequence shown in the illustration.

Torque:
13 N*m (129 kgf*cm, 9 ft.*lbf)

NOTICE:

Tighten each bolt uniformly while keeping the camshaft level.



x.
A116216

Install No. 2 camshaft.


y.
A116224E09
1.458,0.49 0.813,0.198 true 1.51,0.583 0.469,1.333 true 1.469,0.917 1.469,1.792 true 0.625,0.094 0.823,0.271 0.198,0.177 10 false *a 0.292,1.271 0.469,1.448 0.177,0.177 10 false *b 1.375,1.781 1.594,1.958 0.219,0.177 10 false *c

Hold the chain, and align the timing mark on the camshaft timing sprocket with the paint mark of the chain.

Text in Illustration
*a Paint Mark
*b Timing Mark
*c Pin


z.

Align the alignment pin hole in the camshaft timing sprocket with the alignment pin of the camshaft, and install the sprocket onto the camshaft.


aa.
A116215

Provisionally install the flange bolt.


ab.
A116223E11
1.177,2.177 0.865,2.604 true 1.5,1.563 2.635,2.594 2.635,2.594 2.802,1.573 true 1.938,1.573 2.635,2.594 2.635,2.594 2.375,1.573 true 1.073,0.208 1.229,0.385 0.156,0.177 10 false 3 1.708,0.198 1.865,0.375 0.156,0.177 10 false 1 2.354,0.198 2.51,0.375 0.156,0.177 10 false 2 3,0.198 3.156,0.375 0.156,0.177 10 false 4 0.375,0.969 0.531,1.146 0.156,0.177 10 false 5 2.563,2.625 2.76,2.802 0.198,0.177 10 false *b 0.729,2.604 0.917,2.781 0.188,0.177 10 false *a

Examine the front marks and the numbers of No. 1 camshaft bearing cap and No. 2 camshaft bearing cap and check that the sequence is as shown in the illustration. Then uniformly tighten the bolts in several steps, in the sequence shown in the illustration.

Text in Illustration
*a No. 1 Bearing Cap
*b No. 2 Bearing Cap

Torque:
for No. 2 bearing cap : 13 N*m (129 kgf*cm, 9 ft.*lbf)
for No. 1 bearing cap : 23 N*m (235 kgf*cm, 17 ft.*lbf)

NOTICE:

Tighten each bolt uniformly while keeping the camshaft level.



ac.
A116225

Using a union nut wrench, hold the hexagonal lobe of No. 2 camshaft and install the flange bolt.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



ad.

Remove the bar from the timing chain tensioner.


ae.
A116203E25
2.156,1.063 2.469,1.833 true 2.417,1.833 2.604,2.01 0.188,0.177 10 false *a

Turn the crankshaft damper and align its timing notch with the timing mark "0" of the oil pump.

Text in Illustration
*a Timing Notch


af.
A116207E14
1.094,0.729 1.135,1.781 1.135,1.781 2.031,1.521 true 2.208,1.031 1.156,1.771 true 1.177,0.625 2.5,0.177 2.5,0.177 2.198,0.917 true 2.521,0.042 2.719,0.229 0.198,0.188 9 true *a 0.979,1.771 1.146,1.948 0.167,0.177 10 false *b

Check that all the pairs of timing marks are aligned.

Text in Illustration
*a Paint Marks
*b Timing Marks


ag.

Apply adhesive to the 2 or 3 threads of the screw plug.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or Equivalent



ah.
G100163

Using an 8 mm hexagon wrench, install the screw plug.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)


ai.

Install the engine mounting insulator sub-assembly RH (See page Engine / Hybrid System>1NZ-FE LUBRICATION>OIL PUMP>INSTALLATION). (for Hatchback)


aj.

Install the fan and generator V belt (See page Engine / Hybrid System>1NZ-FE ENGINE MECHANICAL>DRIVE BELT>INSTALLATION).


ak.

Adjust the fan and generator V belt (See page Engine / Hybrid System>1NZ-FE ENGINE MECHANICAL>DRIVE BELT>INSTALLATION).


al.

Hide 11201 11.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 23820 12.CONNECT FUEL VAPOR FEED HOSE ASSEMBLY

Hide 15.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

Hide 16.INSPECT FOR ENGINE OIL LEAK

Hide 51441C 18.INSTALL ENGINE UNDER COVER RH (for Plastic Type)

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)

Hide 19.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (for Metal Type)

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)