Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(w/ Toyota Safety Sense) › from 2017.01
RM19S0E _57 Power Source / Network _051489 NETWORKING _0307623 CAN COMMUNICATION SYSTEM(w/ Toyota Safety Sense) U

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Toyota Safety Sense)  TERMINALS OF ECU  


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:
·

Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or any doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).





JUNCTION CONNECTOR


a.

NO. 1 JUNCTION CONNECTOR

U158584C01
1.385,1.302 1.073,1.052 true 1.479,1.292 1.146,0.875 true 1.396,1.5 1.083,1.74 true 1.49,1.5 1.156,1.917 true 5.813,1.333 6.063,1.281 true 5.813,1.49 6.063,1.521 true 5.531,1.292 5.875,0.688 true 5.521,1.5 5.865,2.104 true 4.833,1.49 4.417,1.917 true 4.938,1.5 4.583,2.083 true 5.042,1.5 4.833,2.167 true 5.708,1.51 6,1.833 true 5.688,1.302 6,1 true 4.813,1.292 4.417,0.917 true 4.917,1.281 4.417,0.583 true 5.021,1.281 4.417,0.25 true 1.646,0.344 1.917,0.51 0.271,0.167 10 false A61 0.5,0.958 1.052,1.146 0.552,0.188 10 false CANH*b 0.51,1.646 1.031,1.833 0.521,0.188 10 false CANL*b 0.594,0.75 1.146,0.938 0.552,0.188 10 false CANH*a 0.594,1.854 1.125,2.042 0.531,0.188 10 false CANL*a 5.188,0.354 5.458,0.521 0.271,0.167 10 false F82 6.115,1.177 6.99,1.365 0.875,0.188 10 false CANH*c 6.115,1.448 6.99,1.635 0.875,0.188 10 false CANL*c 5.938,0.552 6.75,0.74 0.813,0.188 10 false CANH*e 5.885,2.125 6.823,2.292 0.938,0.167 10 false CANL*e 3.906,1.885 4.844,2.052 0.938,0.167 10 false CANL*h 4.125,2.094 4.729,2.344 0.604,0.25 10 false CANL*g 4.719,2.198 5.323,2.448 0.604,0.25 10 false CANL*f 6.052,1.781 6.927,1.969 0.875,0.188 10 false CANL*d 6.083,0.865 6.958,1.052 0.875,0.188 10 false CANH*d 3.906,0.125 4.719,0.313 0.813,0.188 10 false CANH*f 3.854,0.438 4.667,0.625 0.813,0.188 10 false CANH*g 3.854,0.802 4.667,0.99 0.813,0.188 10 false CANH*h
*a to ECM *b to Skid Control ECU (Brake Actuator Assembly)
*c to Main Body ECU (Multiplex Network Body ECU) *d to Pre-crash Safety City Sensor
*e to No. 2 Junction Connector *f to Central Gateway ECU (Network Gateway ECU)
*g to Radio and Display Receiver Assembly*1 or Navigation Receiver Assembly*2 *h to Central Gateway ECU (Network Gateway ECU)


Terminal No. (Symbol) Wiring Color Connect to
A61-9 (CANH) L ECM
A61-20 (CANL) W
A61-10 (CANH) G Skid Control ECU (Brake Actuator Assembly)
A61-21 (CANL) W
F82-1 (CANH) R Main Body ECU (Multiplex Network Body ECU)
F82-12 (CANL) W
F82-2 (CANH) LG Pre-crash Safety City Sensor
F82-13 (CANL) W
F82-4 (CANH) SB No. 2 Junction Connector
F82-15 (CANL) W
F82-9 (CANH) R Central Gateway ECU (Network Gateway ECU)
F82-20 (CANL) W
F82-10 (CANH) BE Radio and Display Receiver Assembly*1 or Navigation Receiver Assembly*2
F82-21 (CANL) W
F82-11 (CANH) SB Central Gateway ECU (Network Gateway ECU)
F82-22 (CANL) W

*1: for Radio and Display Type

*2: for Navigation Receiver Type



b.

NO. 2 JUNCTION CONNECTOR

U158588C01
4.042,1.302 4.438,1.271 true 3.177,1.302 2.833,1.167 true 3.542,1.281 3.167,0.25 true 4.031,1.49 4.427,1.521 true 3.177,1.458 2.833,1.75 true 3.563,1.479 3.25,2.5 true 3.76,1.281 4.24,0.76 true 3.781,1.49 4.24,2.021 true 3.344,1.292 3,0.667 true 3.375,1.49 3.021,2.115 true 3.448,1.292 3.083,0.417 true 3.469,1.49 3.167,2.333 true 3.25,1.49 2.917,1.917 true 3.25,1.292 2.833,0.917 true 3.438,0.365 3.708,0.531 0.271,0.167 10 false F83 4.479,1.188 5.354,1.375 0.875,0.188 10 false CANH*a 4.469,1.458 5.344,1.646 0.875,0.188 10 false CANL*a 2.281,1.063 2.833,1.25 0.552,0.188 10 false CANH*g 2.313,1.635 2.833,1.823 0.521,0.188 10 false CANL*g 2.646,0.135 3.198,0.323 0.552,0.188 10 false CANH*c 2.802,2.5 3.333,2.688 0.531,0.188 10 false CANL*c 4.281,0.656 5.094,0.844 0.813,0.188 10 false CANH*b 2.469,0.552 3.281,0.74 0.813,0.188 10 false CANH*e 4.292,1.958 5.229,2.125 0.938,0.167 10 false CANL*b 2.51,2.031 3.448,2.198 0.938,0.167 10 false CANL*e 2.521,0.333 3.333,0.521 0.813,0.188 10 false CANH*d 2.656,2.26 3.594,2.427 0.938,0.167 10 false CANL*d 2.417,1.854 2.938,2.042 0.521,0.188 10 false CANL*f 2.323,0.813 2.875,1 0.552,0.188 10 false CANH*f
*a to Steering Angle Sensor (Spiral Cable Sub-assembly) *b to Airbag Sensor Assembly
*c to Power Steering ECU Assembly *d to Combination Meter Assembly
*e to Air Conditioning Amplifier Assembly *f Central Gateway ECU (Network Gateway ECU)
*g to No. 1 Junction Connector - -


Terminal No. (Symbol) Wiring Color Connect to
F83-1 (CANH) P Steering Angle Sensor (Spiral Cable Sub-assembly)
F83-12 (CANL) W
F83-4 (CANH) B Airbag Sensor Assembly
F83-15 (CANL) W
F83-6 (CANH) LG Power Steering ECU Assembly
F83-17 (CANL) W
F83-7 (CANH) G Combination Meter Assembly
F83-18 (CANL) W
F83-8 (CANH) V Air Conditioning Amplifier Assembly
F83-19 (CANL) W
F83-9 (CANH) BE Central Gateway ECU (Network Gateway ECU)
F83-20 (CANL) W
F83-10 (CANH) SB No. 1 Junction Connector
F83-21 (CANL) W



CHECK DLC3


U126783E07
4.229,1.969 4.521,2.344 true 4.292,0.844 3.865,1.375 true 3,0.854 3.427,1.385 true 3.802,1.969 3.521,2.344 true 3.083,2.271 3.531,2.438 0.448,0.167 10 false CANL 4.375,0.75 4.823,0.917 0.448,0.167 10 false CANH 4.604,2.271 4.958,2.438 0.354,0.167 10 false BAT 2.75,0.771 3.104,0.938 0.354,0.167 10 false CG 3.51,0.729 3.802,0.885 0.292,0.156 10 false F4

a.

Turn the ignition switch off.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
F4-6 (CANH) - F4-14 (CANL) GR - W Ignition switch off 54 to 66 Ω
F4-6 (CANH) - F4-16 (BAT) GR - BE Ignition switch off 6 kΩ or higher
F4-14 (CANL) - F4-16 (BAT) W - BE Ignition switch off 6 kΩ or higher
F4-6 (CANH) - F4-4 (CG) GR - W-B Ignition switch off 200 Ω or higher
F4-14 (CANL) - F4-4 (CG) W - W-B Ignition switch off 200 Ω or higher



CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)


U161143E04
3.958,0.99 4.302,1.292 true 3.542,0.917 3.896,0.292 true 3.667,0.917 4.438,0.365 true 4.042,0.781 5,0.573 true 3.115,0.781 2.781,0.333 true 3.188,0.979 2.5,1.417 true 3.302,0.99 2.833,1.5 true 3.406,0.99 3.25,1.5 true 3.427,0.219 3.833,0.417 0.406,0.198 10 false F139 3.927,0.198 4.458,0.375 0.531,0.177 10 false CA4H 4.469,0.281 4.885,0.458 0.417,0.177 10 false CA4L 4.177,1.292 4.667,1.469 0.49,0.177 10 false CA6H 5.031,0.479 5.469,0.656 0.438,0.177 10 false CA6L 2.365,0.24 2.896,0.417 0.531,0.177 10 false CA3H 2.125,1.375 2.542,1.552 0.417,0.177 10 false CA3L 2.479,1.51 2.896,1.688 0.417,0.177 10 false CAYL 2.99,1.521 3.406,1.698 0.417,0.177 10 false CAYH

a.
U161134C04
0.469,0.979 0.271,1.813 true 2.927,0.969 3.135,1.792 true 2.115,1.875 1.781,1.198 true 1.323,1.875 1.646,1.198 true 0.073,0.042 0.24,0.198 0.167,0.156 10 false *a 1.552,0.167 1.896,0.344 0.344,0.177 10 false F139 0.042,1.823 0.448,1.969 0.406,0.146 10 false BATT 1.885,1.885 2.292,2.031 0.406,0.146 10 false CA4H 2.938,1.792 3.302,1.938 0.365,0.146 10 false GND 1.073,1.885 1.479,2.031 0.406,0.146 10 false CA4L
*a Front view of wire harness connector
(to Central Gateway ECU (Network Gateway ECU))


Disconnect the central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

for Bus 2
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
F139-18 (CA4H) - F139-17 (CA4L) BE - W Ignition switch off 54 to 69 Ω
F139-18 (CA4H) - F139-10 (GND) BE - W-B Ignition switch off 200 Ω or higher
F139-17 (CA4L) - F139-10 (GND) W - W-B Ignition switch off 200 Ω or higher
F139-18 (CA4H) - F139-1 (BATT) BE - SB Ignition switch off 6 kΩ or higher
F139-17 (CA4L) - F139-1 (BATT) W - SB Ignition switch off 6 kΩ or higher


c.
U161122C02
2.042,0.969 2.479,0.135 true 0.427,0.854 1.042,0.99 true 2.375,0.969 2.677,0.406 true 2.01,1.135 2.906,1.646 true 1,0.417 1.385,0.969 true 0.667,1.667 1.406,1.135 true 0.917,1.833 1.51,1.125 true 1.25,1.917 1.583,1.125 true 1.49,0.313 1.927,0.521 0.438,0.208 10 false F139 0.094,0.094 0.427,0.302 0.333,0.208 10 false *a 2.698,0.281 3.094,0.5 0.396,0.219 10 false BATT 0.094,0.76 0.458,0.979 0.365,0.219 10 false GND 2.51,0.042 2.906,0.26 0.396,0.219 10 false CA6L 2.938,1.573 3.333,1.792 0.396,0.219 10 false CA6H 0.615,0.323 1.063,0.573 0.448,0.25 10 false CA3H 0.302,1.594 0.75,1.844 0.448,0.25 10 false CA3L 0.563,1.833 1.01,2.083 0.448,0.25 10 false CAYL 1.01,1.948 1.51,2.104 0.5,0.156 10 false CAYH
*a Rear view of wire harness connector
(to Central Gateway ECU (Network Gateway ECU))


Reconnect the central gateway ECU (network gateway ECU) connector.


d.

Measure the resistance according to the value(s) in the table below.

for V Bus
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
F139-14 (CA6H) - F139-5 (CA6L) GR - W Ignition switch off 54 to 66 Ω
F139-14 (CA6H) - F139-10 (GND) GR - W-B Ignition switch off 200 Ω or higher
F139-5 (CA6L) - F139-10 (GND) W - W-B Ignition switch off 200 Ω or higher
F139-14 (CA6H) - F139-1 (BATT) GR - SB Ignition switch off 6 kΩ or higher
F139-5 (CA6L) - F139-1 (BATT) W - SB Ignition switch off 6 kΩ or higher

for Bus 3
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
F139-6 (CA3H) - F139-21 (CA3L) R - W Ignition switch off 54 to 69 Ω
F139-6 (CA3H) - F139-10 (GND) R - W-B Ignition switch off 200 Ω or higher
F139-21 (CA3L) - F139-10 (GND) W - W-B Ignition switch off 200 Ω or higher
F139-6 (CA3H) - F139-1 (BATT) R - SB Ignition switch off 6 kΩ or higher
F139-21 (CA3L) - F139-1 (BATT) W - SB Ignition switch off 6 kΩ or higher
F139-19 (CAYH) - F139-20 (CAYL) SB - W Ignition switch off 54 to 69 Ω
F139-19 (CAYH) - F139-10 (GND) SB - W-B Ignition switch off 200 Ω or higher
F139-20 (CAYL) - F139-10 (GND) W - W-B Ignition switch off 200 Ω or higher
F139-19 (CAYH) - F139-1 (BATT) SB - SB Ignition switch off 6 kΩ or higher
F139-20 (CAYL) - F139-1 (BATT) W - SB Ignition switch off 6 kΩ or higher



CHECK ECM


U135064E05
5.094,1.135 4.833,0.729 true 2.479,1.135 2.219,0.729 true 6.635,1.125 6.448,0.719 true 4.698,2.094 5.094,1.292 true 5.885,0.385 6.302,0.594 0.417,0.208 10 false A83 2.521,0.531 2.917,0.75 0.396,0.219 10 false B89 4.396,0.625 4.979,0.781 0.583,0.156 10 false CANH 4.271,2.031 4.823,2.188 0.552,0.156 10 false CANL 6.229,0.625 6.646,0.781 0.417,0.156 10 false +B 1.99,0.625 2.406,0.781 0.417,0.156 10 false E1

a.

Disconnect the ECM connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
A83-13 (CANH) - A83-26 (CANL) L - W Ignition switch off 108 to 132 Ω
A83-13 (CANH) - A83-2 (+B) L - B Ignition switch off 6 kΩ or higher
A83-26 (CANL) - A83-2 (+B) W - B Ignition switch off 6 kΩ or higher
A83-13 (CANH) - B89-16 (E1) L - W-B Ignition switch off 200 Ω or higher
A83-26 (CANL) - B89-16 (E1) W - W-B Ignition switch off 200 Ω or higher



CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU), INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (2 Connector Type)


E351568C01
0.25,0.25 0.563,0.406 0.313,0.156 10 false *1 0.917,6.75 1.229,6.906 0.313,0.156 10 false *2 0.927,0.938 1.24,1.135 0.313,0.198 10 false 3D 0.917,1.573 1.229,1.771 0.313,0.198 10 false 3C 0.927,2.104 1.24,2.302 0.313,0.198 10 false 3F 6.375,0.979 6.688,1.177 0.313,0.198 10 false 3B 6.375,1.604 6.688,1.802 0.313,0.198 10 false 3A 3.792,0.802 4.104,1 0.313,0.198 10 false MB 3.667,2.885 3.979,3.083 0.313,0.198 10 false MB 6.083,3.854 6.396,4.052 0.313,0.198 10 false 3F 3.969,3.854 4.281,4.052 0.313,0.198 10 false 3C 1.458,3.854 1.771,4.052 0.313,0.198 10 false 3D 1.615,5.24 1.927,5.438 0.313,0.198 10 false 3B 5.375,5.24 5.688,5.438 0.313,0.198 10 false 3A 3.729,6.458 4.188,6.656 0.458,0.198 10 false F76 2.896,6.458 3.51,6.656 0.615,0.198 10 false F136 2.458,7.5 3.073,7.698 0.615,0.198 10 false F136 4.823,7.49 5.281,7.688 0.458,0.198 10 false F76
*1 Instrument Panel Junction Block Assembly *2 Main Body ECU (Multiplex Network Body ECU)


a.

Disconnect the main body ECU (multiplex network body ECU) connector.


b.

Disconnect the instrument panel junction block assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
F76-14 (CANH) - F76-13 (CANL) R - W Ignition switch off 54 to 69 Ω
F76-14 (CANH) - 3C-21 R - L Ignition switch off 6 kΩ or higher
F76-13 (CANL) - 3C-21 W - L Ignition switch off 6 kΩ or higher
F76-14 (CANH) - 3B-8 R - W-B Ignition switch off 200 Ω or higher
F76-13 (CANL) - 3B-8 W - W-B Ignition switch off 200 Ω or higher



CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU), INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (1 Connector Type)


E351569C01
0.167,0.167 0.479,0.323 0.313,0.156 10 false *1 1.25,6.75 1.563,6.906 0.313,0.156 10 false *2 3.802,0.792 4.115,0.99 0.313,0.198 10 false MB 3.802,2.865 4.115,3.063 0.313,0.198 10 false MB 0.938,0.906 1.25,1.104 0.313,0.198 10 false 3D 0.938,1.51 1.25,1.708 0.313,0.198 10 false 3C 0.948,2.135 1.26,2.333 0.313,0.198 10 false 3F 1.521,3.854 1.833,4.052 0.313,0.198 10 false 3D 6.5,0.906 6.813,1.104 0.313,0.198 10 false 3B 6.5,1.51 6.813,1.708 0.313,0.198 10 false 3A 3.99,3.854 4.302,4.052 0.313,0.198 10 false 3C 6.094,3.885 6.406,4.083 0.313,0.198 10 false 3F 5.49,5.208 5.802,5.406 0.313,0.198 10 false 3A 1.635,5.219 1.948,5.417 0.313,0.198 10 false 3B 3.802,6.458 4.26,6.656 0.458,0.198 10 false F76 3.708,7.531 4.167,7.729 0.458,0.198 10 false F76
*1 Instrument Panel Junction Block Assembly *2 Main Body ECU (Multiplex Network Body ECU)


a.

Disconnect the main body ECU (multiplex network body ECU) connector.


b.

Disconnect the instrument panel junction block assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
F76-14 (CANH) - F76-13 (CANL) R - W Ignition switch off 54 to 69 Ω
F76-14 (CANH) - 3C-21 R - L Ignition switch off 6 kΩ or higher
F76-13 (CANL) - 3C-21 W - L Ignition switch off 6 kΩ or higher
F76-14 (CANH) - 3B-8 R - W-B Ignition switch off 200 Ω or higher
F76-13 (CANL) - 3B-8 W - W-B Ignition switch off 200 Ω or higher



CHECK COMBINATION METER ASSEMBLY


U127243E04
4.323,1.156 4.063,1.552 true 3.385,1.156 3.125,1.552 true 4.479,1.156 4.74,1.552 true 5.646,1.156 5.906,1.552 true 4.458,0.333 4.75,0.49 0.292,0.156 10 false F1 3.635,1.49 4.188,1.646 0.552,0.156 10 false CANH 4.792,1.479 5.323,1.635 0.531,0.156 10 false CANL 2.979,1.479 3.229,1.635 0.25,0.156 10 false B 5.948,1.531 6.156,1.688 0.208,0.156 10 false ET

a.

Disconnect the combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
F1-32 (CANH) - F1-31 (CANL) G - W Ignition switch off 108 to 132 Ω
F1-32 (CANH) - F1-40 (B) G - L Ignition switch off 6 kΩ or higher
F1-31 (CANL) - F1-40 (B) W - L Ignition switch off 6 kΩ or higher
F1-32 (CANH) - F1-21 (ET) G - BR Ignition switch off 200 Ω or higher
F1-31 (CANL) - F1-21 (ET) W - BR Ignition switch off 200 Ω or higher



CHECK SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)


U158732E03
4.073,1.823 4.333,2.219 true 4.573,0.854 4.313,1.25 true 2.781,1.24 2.521,0.833 true 4.729,1.448 4.083,1.594 true 3.417,0.594 3.708,0.75 0.292,0.156 10 false A54 4.396,2.167 4.958,2.323 0.563,0.156 10 false CANH 4.781,1.365 5.323,1.521 0.542,0.156 10 false CANL 4.625,0.771 5.042,0.927 0.417,0.156 10 false GND1 2.208,0.771 2.625,0.927 0.417,0.156 10 false +BS

a.

Disconnect the skid control ECU (brake actuator assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
A54-25 (CANH) - A54-14 (CANL) G - W Ignition switch off 54 to 69 Ω
A54-25 (CANH) - A54-12 (+BS) G - W Ignition switch off 6 kΩ or higher
A54-14 (CANL) - A54-12 (+BS) W - W Ignition switch off 6 kΩ or higher
A54-25 (CANH) - A54-1 (GND1) G - W-B Ignition switch off 200 Ω or higher
A54-14 (CANL) - A54-1 (GND1) W - W-B Ignition switch off 200 Ω or higher



CHECK AIRBAG SENSOR ASSEMBLY


U158733E02
2.844,1.563 2.188,2.219 true 3.021,1.823 3.396,2.208 true 6.604,1.75 6.219,2.125 true 5.594,0.885 5.969,1.26 true 1.729,2.167 2.167,2.302 0.438,0.135 10 false CANH 3.448,2.146 3.875,2.281 0.427,0.135 10 false CANL 2.354,0.625 2.635,0.781 0.281,0.156 10 false F16 5.938,2.073 6.24,2.208 0.302,0.135 10 false BAT 5.344,0.813 5.646,0.948 0.302,0.135 10 false CG 5.969,0.719 6.219,0.875 0.25,0.156 10 false F4

a.

Disconnect the airbag sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
F16-13 (CANH) - F16-22 (CANL) B - W Ignition switch off 54 to 69 Ω
F16-13 (CANH) - F4-16 (BAT) B - BE Ignition switch off 6 kΩ or higher
F16-22 (CANL) - F4-16 (BAT) W - BE Ignition switch off 6 kΩ or higher
F16-13 (CANH) - F4-4 (CG) B - W-B Ignition switch off 200 Ω or higher
F16-22 (CANL) - F4-4 (CG) W - W-B Ignition switch off 200 Ω or higher



CHECK STEERING ANGLE SENSOR (SPIRAL CABLE SUB-ASSEMBLY)


U127162E04
3.427,1.792 3.146,2.396 true 3.885,1.802 4.167,2.406 true 4.135,1.802 4.906,2.396 true 2.917,1.802 2.146,2.396 true 2.698,2.333 3.24,2.479 0.542,0.146 10 false CANH 4.208,2.344 4.729,2.49 0.521,0.146 10 false CANL 4.938,2.333 5.385,2.51 0.448,0.177 10 false ESS 1.865,2.333 2.156,2.479 0.292,0.146 10 false BAT 3.521,0.542 3.813,0.698 0.292,0.156 10 false F30

a.

Disconnect the steering angle sensor (spiral cable sub-assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
F30-4 (CANH) - F30-3 (CANL) P - W Ignition switch off 54 to 69 Ω
F30-4 (CANH) - F30-6 (BAT) P - SB Ignition switch off 6 kΩ or higher
F30-3 (CANL) - F30-6 (BAT) W - SB Ignition switch off 6 kΩ or higher
F30-4 (CANH) - F30-2 (ESS) P - BR Ignition switch off 200 Ω or higher
F30-3 (CANL) - F30-2 (ESS) W - BR Ignition switch off 200 Ω or higher



CHECK POWER STEERING ECU ASSEMBLY


U126895E03
5.021,1.615 5.573,2.302 true 4.24,1.625 3.667,2.313 true 2.104,1.563 2.656,2.26 true 1.958,1.563 1.396,2.26 true 4.531,0.729 4.823,0.885 0.292,0.156 10 false A42 5.646,2.281 5.938,2.438 0.292,0.156 10 false PIG 3.26,2.281 3.698,2.438 0.438,0.156 10 false PGND 2.698,2.229 3.135,2.385 0.438,0.156 10 false CANH 1,2.208 1.438,2.365 0.438,0.156 10 false CANL 2.052,0.74 2.344,0.896 0.292,0.156 10 false F6

a.

Disconnect the power steering ECU assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
F6-7 (CANH) - F6-8 (CANL) LG - W Ignition switch off 54 to 69 Ω
F6-7 (CANH) - A42-1 (PIG) LG - W Ignition switch off 6 kΩ or higher
F6-8 (CANL) - A42-1 (PIG) W - W Ignition switch off 6 kΩ or higher
F6-7 (CANH) - A42-2 (PGND) LG - W-B Ignition switch off 200 Ω or higher
F6-8 (CANL) - A42-2 (PGND) W - W-B Ignition switch off 200 Ω or higher



CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY


U127350C03
3.031,0.74 2.771,0.344 true 4.677,1.385 4.417,0.99 true 3.146,0.729 3.406,0.333 true 5.354,2.677 5.594,2.302 true 2.448,1.302 2.75,0.823 true 1.094,2.667 1.396,2.198 true 1.344,1.948 1.083,1.552 true 1.49,1.958 1.75,1.563 true 1.063,0.74 1.375,0.948 0.313,0.208 10 false F42 0.219,2.031 0.51,2.188 0.292,0.156 10 false F41 3.99,2.031 4.281,2.188 0.292,0.156 10 false F4 1.438,0.75 1.729,0.906 0.292,0.156 10 false *A 0.573,2.021 0.865,2.177 0.292,0.156 10 false *B 3.458,0.219 3.927,0.406 0.469,0.188 10 false CANH 2.365,0.219 2.844,0.406 0.479,0.188 10 false CANL 2.135,1.25 2.552,1.406 0.417,0.156 10 false GND 4.74,1.333 5.156,1.49 0.417,0.156 10 false B 5.073,2.625 5.49,2.781 0.417,0.156 10 false BAT 0.771,2.604 1.188,2.76 0.417,0.156 10 false GND 1.802,1.438 2.26,1.635 0.458,0.198 10 false CANH 0.677,1.448 1.125,1.625 0.448,0.177 10 false CANL
*A for Automatic Air Conditioning System *B for Manual Air Conditioning System


a.

Disconnect the F42*1 or F41*2 air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
F42-11 (CANH) - F42-12 (CANL)*1
F41-8 (CANH) - F41-9 (CANL)*2
V - W Ignition switch off 54 to 69 Ω
F42-11 (CANH) - F42-21 (B)*1
F41-8 (CANH) - F4-16 (BAT)*2
V - BE Ignition switch off 6 kΩ or higher
F42-12 (CANL) - F42-21 (B)*1
F41-9 (CANL) - F4-16 (BAT)*2
W - BE Ignition switch off 6 kΩ or higher
F42-11 (CANH) - F42-14 (GND)*1
F41-8 (CANH) - F41-23 (GND)*2
V - W-B Ignition switch off 200 Ω or higher
F42-12 (CANL) - F42-14 (GND)*1
F41-9 (CANL) - F41-23 (GND)*2
W - W-B Ignition switch off 200 Ω or higher

*1: for Automatic Air Conditioning System

*2: for Manual Air Conditioning System




CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY (for Radio and Display Type)


U158739E04
4.271,1.469 4.604,0.969 true 4.781,0.938 5,1.469 true 2.073,1.135 2.208,1.5 true 1.51,0.938 1.094,1.458 true 1.781,0.271 2.125,0.427 0.344,0.156 10 false F125 4.781,0.271 5.125,0.427 0.344,0.156 10 false F127 2.063,1.5 2.635,1.677 0.573,0.177 10 false GND1 4.865,1.5 5.458,1.635 0.594,0.135 10 false CANH 4.052,1.5 4.646,1.635 0.594,0.135 10 false CANL 0.938,1.5 1.302,1.635 0.365,0.135 10 false +B1

a.

Disconnect the radio and display receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
F127-9 (CANH) - F127-10 (CANL) BE - W Ignition switch off 54 to 69 Ω
F127-9 (CANH) - F125-4 (+B1) BE - SB Ignition switch off 6 kΩ or higher
F127-10 (CANL) - F125-4 (+B1) W - SB Ignition switch off 6 kΩ or higher
F127-9 (CANH) - F125-7 (GND1) BE - BR Ignition switch off 200 Ω or higher
F127-10 (CANL) - F125-7 (GND1) W - BR Ignition switch off 200 Ω or higher



CHECK NAVIGATION RECEIVER ASSEMBLY (for Navigation Receiver Type)


U158740E04
4.271,1.469 4.604,0.969 true 4.792,0.948 5.01,1.479 true 2.073,1.135 2.208,1.5 true 1.51,0.938 1.094,1.458 true 1.781,0.271 2.125,0.427 0.344,0.156 10 false F130 4.781,0.271 5.125,0.427 0.344,0.156 10 false F132 2.073,1.521 2.646,1.719 0.573,0.198 10 false GND1 4.865,1.5 5.458,1.635 0.594,0.135 10 false CANH 4.052,1.5 4.646,1.635 0.594,0.135 10 false CANL 0.938,1.5 1.302,1.635 0.365,0.135 10 false +B1

a.

Disconnect the navigation receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
F132-9 (CANH) - F132-10 (CANL) BE - W Ignition switch off 54 to 69 Ω
F132-9 (CANH) - F130-4 (+B1) BE - SB Ignition switch off 6 kΩ or higher
F132-10 (CANL) - F130-4 (+B1) W - SB Ignition switch off 6 kΩ or higher
F132-9 (CANH) - F130-7 (GND1) BE - BR Ignition switch off 200 Ω or higher
F132-10 (CANL) - F130-7 (GND1) W - BR Ignition switch off 200 Ω or higher



CHECK PRE-CRASH SAFETY CITY SENSOR


U161148E04
5.833,1.625 6.031,1.969 true 1.885,1.625 2.083,1.969 true 1.615,1.625 1.417,1.969 true 0.927,0.969 1.615,1.365 true 1.802,0.469 2.323,0.74 0.521,0.271 10 false L11 5.219,0.469 5.75,0.698 0.531,0.229 10 false F4 5.917,2 6.448,2.146 0.531,0.146 10 false BAT 0.521,0.896 1.052,1.042 0.531,0.146 10 false CA1P 1.208,1.99 1.74,2.135 0.531,0.146 10 false CA1N 1.938,1.99 2.469,2.135 0.531,0.146 10 false GND

a.

Disconnect the pre-crash safety city sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
L11-5 (CA1P) - L11-11 (CA1N) LG - W Ignition switch off 54 to 69 Ω
L11-5 (CA1P) - F4-16 (BAT) LG - BE Ignition switch off 6 kΩ or higher
L11-11 (CA1N) - F4-16 (BAT) W - BE Ignition switch off 6 kΩ or higher
L11-5 (CA1P) - L11-10 (GND) LG - W-B Ignition switch off 200 Ω or higher
L11-11 (CA1N) - L11-10 (GND) W - W-B Ignition switch off 200 Ω or higher



Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION