Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(w/ Toyota Safety Sense) › from 2017.01
RM19S0E _57 Power Source / Network _051489 NETWORKING _0307623 CAN COMMUNICATION SYSTEM(w/ Toyota Safety Sense) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Toyota Safety Sense)  Steering Angle Sensor Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Steering Angle Sensor Communication Stop Mode Either condition is met:
·

Communication stop for "Spiral cable (Steering Angle Sensor)" is indicated on the "Communication Bus Check" screen of the GTS.

(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Steering Angle Sensor Communication Stop Mode" in "DTC Combination Table" are output.

(Click here)


·

Power source or inside steering angle sensor (spiral cable sub-assembly)

·

Steering angle sensor (spiral cable sub-assembly) branch wire or connector

·

Steering angle sensor (spiral cable sub-assembly)



WIRING DIAGRAM

E229245E11
1.458,1.052 1.885,1.219 0.427,0.167 10 false CANH 1.458,1.5 1.885,1.667 0.427,0.167 10 false CANL 0.521,1.979 0.927,2.146 0.406,0.167 10 false F83 5.063,0.958 5.271,1.125 0.208,0.167 10 false 4 5.292,1.042 5.719,1.208 0.427,0.167 10 false CANH 5.292,1.51 5.719,1.677 0.427,0.167 10 false CANL 1.938,2.656 3.313,2.969 1.375,0.313 10 false from IG1 NO. 1 Relay 3.625,2.813 4.563,2.979 0.938,0.167 10 false ECU-IG NO. 1 5.292,3.229 5.719,3.438 0.427,0.208 10 false ESS 5.063,1.396 5.271,1.563 0.208,0.167 10 false 3 1.979,0.958 2.156,1.125 0.177,0.167 10 false 1 1.948,1.396 2.135,1.563 0.188,0.167 10 false 12 5.292,2.646 5.719,2.813 0.427,0.167 10 false IG 5.063,2.563 5.271,2.729 0.208,0.167 10 false 5 2.26,2.208 3.333,2.521 1.073,0.313 10 false from D.C.C Fuse 3.854,2.344 4.292,2.51 0.438,0.167 10 false DOME 5.292,2.208 5.719,2.375 0.427,0.167 10 false BAT 5.063,2.115 5.271,2.281 0.208,0.167 10 false 6 5.063,3.146 5.26,3.333 0.198,0.188 10 false 2 0.521,2.156 2.156,2.479 1.635,0.323 10 false No. 2 Junction Connector 4.823,3.885 5.208,4.052 0.385,0.167 10 false F30 4.823,4.073 6.646,4.74 1.823,0.667 10 false Steering Angle Sensor (Spiral Cable Sub-assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Turn the ignition switch off before measuring the resistances between CAN bus main wires and between CAN bus branch wires.

·

Turn the ignition switch off before inspecting CAN bus wires for a ground short.

·

After the ignition switch is turned off, check that the key reminder warning system are not operating.

·

Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (STEERING ANGLE SENSOR (SPIRAL CABLE SUB-ASSEMBLY) BRANCH WIRE)
U127163C02
2,2.25 2.323,2.74 true 1.469,2.25 1.146,2.74 true 1.573,0.479 1.865,0.635 0.292,0.156 10 false F30 0.177,0.094 0.469,0.25 0.292,0.156 10 false *a 2.406,2.635 2.823,2.792 0.417,0.156 10 false CANH 0.719,2.646 1.135,2.802 0.417,0.156 10 false CANL
*a Front view of wire harness connector
(to Steering Angle Sensor (Spiral Cable Sub-assembly))


a.

Disconnect the steering angle sensor (spiral cable sub-assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F30-4 (CANH) - F30-3 (CANL) Ignition switch off 54 to 69 Ω




OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (STEERING ANGLE SENSOR (SPIRAL CABLE SUB-ASSEMBLY) BRANCH WIRE)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
E346210C02
1.469,0.583 1.969,0.833 0.5,0.25 0.729,2.781 1.146,2.25 true 1.708,2.802 2.125,2.271 true 2.75,2.792 2.604,2.26 true 0.177,0.177 0.49,0.375 0.313,0.198 10 false *a 1.604,0.615 2.063,0.813 0.458,0.198 10 false F30 0.5,2.813 0.958,3.01 0.458,0.198 10 false ESS 2.667,2.833 3.125,3.031 0.458,0.198 10 false BAT 1.583,2.833 2.042,3.031 0.458,0.198 10 false IG
*a Front view of wire harness connector
(to Steering Angle Sensor (Spiral Cable Sub-assembly))


a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F30-5 (IG) - Body ground Ignition switch ON 11 to 14 V
F30-6 (BAT) - Body ground Always 11 to 14 V



b.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
F30-2 (ESS) - Body ground Always Below 1 Ω



OK

REPLACE STEERING ANGLE SENSOR (SPIRAL CABLE SUB-ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)