Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(w/ Toyota Safety Sense) › from 2017.01
RM19S0E _57 Power Source / Network _051489 NETWORKING _0307623 CAN COMMUNICATION SYSTEM(w/ Toyota Safety Sense) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Toyota Safety Sense)  Main Body ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Main Body ECU Communication Stop Mode Either condition is met:
·

Communication stop for "Main Body" is indicated on the "Communication Bus Check" screen of the GTS.

(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Main Body ECU Communication Stop Mode" are output.

(Click here)


·

Power source or inside main body ECU (multiplex network body ECU)

·

Main body ECU (multiplex network body ECU) branch wire or connector

·

Main body ECU (multiplex network body ECU)



WIRING DIAGRAM

E229247E05
1.448,0.375 1.875,0.542 0.427,0.167 10 false CANH 1.448,0.823 1.875,0.99 0.427,0.167 10 false CANL 3.26,0.365 3.677,0.542 0.417,0.177 10 false CANH 3.26,0.813 3.729,1.021 0.469,0.208 10 false CANL 0.542,1.313 0.948,1.479 0.406,0.167 10 false F82 2.021,2.115 3.365,2.427 1.344,0.313 10 false from IG1 NO.1 Relay 3.615,2.302 4.5,2.5 0.885,0.198 10 false ECU-IG NO.1 3.604,3.448 4.531,3.625 0.927,0.177 10 false ECU-B NO.1 2.271,3.271 3.344,3.583 1.073,0.313 10 false from D.C.C Fuse 6.51,1.01 6.938,1.177 0.427,0.167 10 false GND1 1.969,0.281 2.146,0.448 0.177,0.167 10 false 1 1.938,0.719 2.125,0.885 0.188,0.167 10 false 12 5.396,1.01 5.823,1.177 0.427,0.167 10 false IG 4.948,1.906 5.24,2.073 0.292,0.167 10 false 40 5.688,1.25 5.979,1.417 0.292,0.167 10 false 32 6.906,1.24 7.083,1.406 0.177,0.167 10 false 11 4.99,3.583 5.313,3.75 0.323,0.167 10 false 8 4.948,2.115 5.229,2.281 0.281,0.167 10 false 3A 4.948,3.073 5.24,3.24 0.292,0.167 10 false 21 4.938,3.26 5.219,3.427 0.281,0.167 10 false 3C 5.375,1.25 5.656,1.417 0.281,0.167 10 false MB 5.906,1.01 6.333,1.177 0.427,0.167 10 false BECU 6.323,1.25 6.615,1.417 0.292,0.167 10 false 30 6,1.25 6.281,1.417 0.281,0.167 10 false MB 6.583,1.24 6.865,1.406 0.281,0.167 10 false MB 4.948,3.771 5.198,3.938 0.25,0.167 10 false 3B 2.938,0.177 3.26,0.344 0.323,0.167 10 false 14 2.938,0.615 3.26,0.781 0.323,0.167 10 false 13 2.917,0.813 3.198,0.979 0.281,0.167 10 false F76 2.906,0.365 3.188,0.531 0.281,0.167 10 false F76 0.542,1.479 2.156,1.802 1.615,0.323 10 false No. 1 Junction Connector 5.396,4.063 7.021,4.708 1.625,0.646 10 false Instrument Panel Junction Block Assembly 3.219,1.313 4.875,1.75 1.656,0.438 10 false Main Body ECU (Multiplex Network Body ECU)

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Turn the ignition switch off before measuring the resistances between CAN bus main wires and between CAN bus branch wires.

·

Turn the ignition switch off before inspecting CAN bus wires for a ground short.

·

After the ignition switch is turned off, check that the key reminder warning system are not operating.

·

Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) BRANCH WIRE)
U127253C02
1.344,1.875 1.833,1.146 true 2.469,1.885 1.979,1.156 true 1.583,0.219 1.875,0.375 0.292,0.156 10 false F76 0.083,0.052 0.375,0.208 0.292,0.156 10 false *a 2.521,1.823 2.938,1.979 0.417,0.156 10 false CANH 0.896,1.813 1.313,1.969 0.417,0.156 10 false CANL
*a Front view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU))


a.

Disconnect the main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F76-14 (CANH) - F76-13 (CANL) Ignition switch off 54 to 69 Ω




OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) BRANCH WIRE)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Remove the main body ECU (multiplex network body ECU) (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


U127352C01
5.094,0.917 4.833,0.51 true 2.896,0.917 2.635,0.51 true 5.406,0.917 5.667,0.51 true 0.115,0.094 0.406,0.25 0.292,0.156 10 false *a 3.469,0.417 3.76,0.573 0.292,0.156 10 false MB 5.719,0.438 6.135,0.594 0.417,0.156 10 false IG 4.406,0.438 4.823,0.594 0.417,0.156 10 false BECU 2.208,0.438 2.625,0.594 0.417,0.156 10 false GND1
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
MB-11 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
MB-30 (BECU) - Body ground Always 11 to 14 V
MB-32 (IG) - Body ground Ignition switch ON 11 to 14 V




OK

3.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

3.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
U127269C01
6.823,2.073 6.583,2.333 true 6.615,2.01 6.333,1.75 true 4.646,2.073 4.406,2.333 true 5.156,1.521 5.5,1.677 0.344,0.156 10 false MB 5.896,1.646 6.375,1.802 0.479,0.156 10 false BECU 4,2.229 4.479,2.385 0.479,0.156 10 false GND1 6.396,2.229 6.573,2.385 0.177,0.156 10 false IG 1.719,1.521 2.063,1.677 0.344,0.156 10 false 3B 0.156,0.083 0.448,0.302 0.292,0.219 10 false *a 1.76,0.188 2.104,0.344 0.344,0.156 10 false 3A 5.188,0.188 5.531,0.344 0.344,0.156 10 false 3C
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


a.

Disconnect the instrument panel junction block assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
MB-11 (GND1) - 3B-8 Always Below 1 Ω
MB-30 (BECU) - 3C-21 Always Below 1 Ω
MB-32 (IG) - 3A-40 Always Below 1 Ω
MB-11 (GND1) or 3B-8 - Body ground Always 10 kΩ or higher
MB-30 (BECU) or 3C-21 - Body ground Always 10 kΩ or higher
MB-32 (IG) or 3A-40 - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY