Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(w/ Toyota Safety Sense) › from 2017.01
RM19S0E _57 Power Source / Network _051489 NETWORKING _0307623 CAN COMMUNICATION SYSTEM(w/ Toyota Safety Sense) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Toyota Safety Sense)  Audio Receiver Assembly Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Audio Receiver Assembly Communication Stop Mode Either condition is met:
·

Communication stop for "Display and Navigation (AVN1)" is indicated on the "Communication Bus Check" screen of the GTS.

(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Audio Receiver Assembly Communication Stop Mode" are output.

(Click here)


·

Power source or inside radio and display receiver assembly*1 or navigation receiver assembly*2

·

Radio and display receiver assembly*1 or navigation receiver assembly*2 branch wire or connector

·

Radio and display receiver assembly*1 or navigation receiver assembly*2



*1: for Radio and Display Type

*2: for Navigation Receiver Type


WIRING DIAGRAM

E296555E06
0.438,1.552 0.844,1.719 0.406,0.167 10 false F82 5.49,0.563 5.698,0.729 0.208,0.167 10 false 9 5.75,0.74 6.177,0.906 0.427,0.167 10 false CANH 5.75,1.146 6.177,1.313 0.427,0.167 10 false CANL 2.5,2.208 3.354,2.563 0.854,0.354 10 false from Battery 4.417,2.333 4.958,2.5 0.542,0.167 10 false GAUGE 5.75,3.063 6.177,3.229 0.427,0.167 10 false GND1 5.448,1.01 5.656,1.177 0.208,0.167 10 false 10 1.74,0.625 2.052,0.792 0.313,0.167 10 false 10 1.74,1.083 2.042,1.281 0.302,0.198 10 false 21 5.75,2.219 6.177,2.385 0.427,0.167 10 false IG 5.49,2.042 5.698,2.208 0.208,0.167 10 false 1 5.49,2.854 5.698,3.021 0.208,0.167 10 false 7 0.438,1.719 2.042,2.042 1.604,0.323 10 false No. 1 Junction Connector 0.156,0.094 2.344,0.344 2.188,0.25 12 false for Radio and Display Type: 5.354,3.052 5.708,3.219 0.354,0.167 10 false F125 5.354,2.646 5.708,2.813 0.354,0.167 10 false F125 5.344,2.219 5.698,2.385 0.354,0.167 10 false F127 5.354,1.198 5.708,1.365 0.354,0.167 10 false F127 5.354,0.74 5.708,0.906 0.354,0.167 10 false F127 5.49,2.448 5.698,2.615 0.208,0.167 10 false 4 5.573,3.656 6.906,3.969 1.333,0.313 10 false Radio and Display Receiver Assembly 1.208,0.74 1.635,0.906 0.427,0.167 10 false CANH 1.219,1.167 1.646,1.333 0.427,0.167 10 false CANL 2.188,2.625 3.396,2.938 1.208,0.313 10 false from DOME Fuse 5.75,2.646 6.177,2.813 0.427,0.167 10 false +B1

E296555E07
0.438,1.563 0.844,1.729 0.406,0.167 10 false F82 5.479,0.542 5.688,0.708 0.208,0.167 10 false 9 5.75,0.719 6.177,0.885 0.427,0.167 10 false CANH 5.75,1.167 6.177,1.333 0.427,0.167 10 false CANL 2.5,2.208 3.354,2.563 0.854,0.354 10 false from Battery 4.417,2.365 4.948,2.552 0.531,0.188 10 false GAUGE 5.75,3.031 6.177,3.198 0.427,0.167 10 false GND1 5.427,1 5.635,1.167 0.208,0.167 10 false 10 1.729,0.635 1.979,0.833 0.25,0.198 10 false 10 1.74,1.073 1.979,1.25 0.24,0.177 10 false 21 5.75,2.198 6.177,2.365 0.427,0.167 10 false IG 5.479,2.021 5.688,2.188 0.208,0.167 10 false 1 5.479,2.844 5.688,3.01 0.208,0.167 10 false 7 0.438,1.729 2.042,2.052 1.604,0.323 10 false No. 1 Junction Connector 0.25,0.104 2.823,0.406 2.573,0.302 12 false for Navigation Receiver Type: 5.354,2.646 5.708,2.813 0.354,0.167 10 false F130 5.354,3.042 5.708,3.208 0.354,0.167 10 false F130 5.354,1.177 5.708,1.344 0.354,0.167 10 false F132 5.344,2.219 5.698,2.385 0.354,0.167 10 false F132 5.354,0.74 5.708,0.906 0.354,0.167 10 false F132 5.479,2.448 5.688,2.615 0.208,0.167 10 false 4 5.115,3.708 7.073,3.927 1.958,0.219 10 false Navigation Receiver Assembly 1.208,0.729 1.635,0.896 0.427,0.167 10 false CANH 1.219,1.188 1.646,1.354 0.427,0.167 10 false CANL 2.188,2.635 3.396,2.948 1.208,0.313 10 false from DOME Fuse 5.75,2.635 6.177,2.802 0.427,0.167 10 false +B1

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Turn the ignition switch off before measuring the resistances between CAN bus main wires and between CAN bus branch wires.

·

Turn the ignition switch off before inspecting CAN bus wires for a ground short.

·

After the ignition switch is turned off, check that the key reminder warning system are not operating.

·

Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CONFIRM VEHICLE TYPE
a.

Confirm vehicle type.

Result
Result Proceed to
for Radio and Display Type A
for Navigation Receiver Type B



A

2.CHECK FOR OPEN IN CAN BUS WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY BRANCH WIRE)

B

4.CHECK FOR OPEN IN CAN BUS WIRE (NAVIGATION RECEIVER ASSEMBLY BRANCH WIRE)
2.CHECK FOR OPEN IN CAN BUS WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY BRANCH WIRE)
a.
U158747C01
1.969,1.26 1.354,0.438 true 2.146,1.26 2.688,0.438 true 0.177,1.063 0.51,1.24 0.333,0.177 10 false F127 2.76,0.333 3.146,0.51 0.385,0.177 10 false CANL 0.906,0.333 1.344,0.521 0.438,0.188 10 false CANH 0.188,0.063 0.458,0.24 0.271,0.177 10 false *a
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Disconnect the radio and display receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F127-9 (CANH) - F127-10 (CANL) Ignition switch off 54 to 69 Ω




OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY BRANCH WIRE)

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
U158635C01
0.75,3.448 0.438,2.958 true 2.26,1.208 2.583,0.719 true 1.24,2.063 1.563,1.573 true 1.552,0.385 1.896,0.542 0.344,0.156 10 false F125 0.104,0.083 0.396,0.24 0.292,0.156 10 false *a 1.552,2.469 1.917,2.625 0.365,0.156 10 false F127 2.656,0.615 3.073,0.771 0.417,0.156 10 false +B1 0.229,2.865 0.646,3.021 0.417,0.156 10 false IG 0.813,1.958 1.229,2.115 0.417,0.156 10 false GND1
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


a.

Disconnect the radio and display receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F125-4 (+B1) - Body ground Always 11 to 14 V
F127-1 (IG) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F125-7 (GND1) - Body ground Always Below 1 Ω




OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK FOR OPEN IN CAN BUS WIRE (NAVIGATION RECEIVER ASSEMBLY BRANCH WIRE)
a.
U158748C01
1.99,1.25 1.365,0.427 true 2.135,1.25 2.667,0.427 true 0.177,1.063 0.51,1.24 0.333,0.177 10 false F132 2.698,0.313 3.083,0.49 0.385,0.177 10 false CANL 0.958,0.323 1.365,0.5 0.406,0.177 10 false CANH 0.125,0.083 0.333,0.26 0.208,0.177 10 false *a
*a Front view of wire harness connector
(to Navigation Receiver Assembly)


Disconnect the navigation receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F132-9 (CANH) - F132-10 (CANL) Ignition switch off 54 to 69 Ω




OK

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (NAVIGATION RECEIVER ASSEMBLY BRANCH WIRE)

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
U158636C01
0.74,3.469 0.427,2.979 true 2.26,1.198 2.583,0.708 true 1.24,2.083 1.563,1.594 true 1.563,0.385 1.906,0.542 0.344,0.156 10 false F130 0.115,0.083 0.406,0.24 0.292,0.156 10 false *a 1.573,2.469 1.938,2.625 0.365,0.156 10 false F132 2.646,0.604 3.063,0.76 0.417,0.156 10 false +B1 0.208,2.854 0.625,3.01 0.417,0.156 10 false IG 0.781,2.021 1.198,2.177 0.417,0.156 10 false GND1
*a Front view of wire harness connector
(to Navigation Receiver Assembly)


a.

Disconnect the navigation receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F130-4 (+B1) - Body ground Always 11 to 14 V
F132-1 (IG) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F130-7 (GND1) - Body ground Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR