There may be a short circuit between one of the CAN bus lines and +B when no resistance exists between terminal 18 (CA4H) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3, or terminal 17 (CA4L) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3.
| Symptom | Trouble Area |
|---|---|
| No resistance exists between terminal 18 (CA4H) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3, or terminal 17 (CA4L) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3. | ·
Short to +B in CAN main bus line ·
Short to +B in CAN branch line ·
ECM ·
Combination meter assembly ·
Airbag sensor assembly ·
Skid control ECU (brake actuator assembly) ·
Main body ECU (multiplex network body ECU) ·
Power steering ECU assembly ·
Steering angle sensor (spiral cable sub-assembly) ·
Air conditioning amplifier assembly ·
Pre-crash safety city sensor ·
No. 1 junction connector ·
No. 2 junction connector |
Turn the ignition switch off before measuring the resistances of the CAN main wire and the CAN branch wire.
After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not in operation.
Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
Disconnect the cable from the negative (-) battery terminal.
Disconnect the No. 2 junction connector.
| *1 | DLC3 |
| *a | Front view of wire harness connector
(to No. 2 Junction Connector) |
| *b | to Steering Angle Sensor (Spiral Cable Sub-assembly) |
| *c | to Airbag Sensor Assembly |
| *d | to Power Steering ECU Assembly |
| *e | to Combination Meter Assembly |
| *f | to Air Conditioning Amplifier Assembly |
| *g | to Central Gateway ECU (Network Gateway ECU) |
| *h | to No. 1 Junction Connector |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| F83-1 (CANH) - F4-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Steering angle sensor (Spiral cable sub-assembly) |
| F83-12 (CANL) - F4-16 (BAT) | |||
| F83-4 (CANH) - F4-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Airbag sensor assembly |
| F83-15 (CANL) - F4-16 (BAT) | |||
| F83-6 (CANH) - F4-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Power steering ECU assembly |
| F83-17 (CANL) - F4-16 (BAT) | |||
| F83-7 (CANH) - F4-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Combination meter assembly |
| F83-18 (CANL) - F4-16 (BAT) | |||
| F83-8 (CANH) - F4-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Air conditioning amplifier assembly |
| F83-19 (CANL) - F4-16 (BAT) | |||
| F83-9 (CANH) - F4-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Central gateway ECU (network gateway ECU) |
| F83-20 (CANL) - F4-16 (BAT) | |||
| F83-10 (CANH) - F4-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | No. 1 junction connector |
| F83-21 (CANL) - F4-16 (BAT) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (No. 1 junction connector main line) | B |
| NG (ECU or sensor bus line) | C |
| NG (Central gateway ECU (network gateway ECU) branch line) | D |
A
B
C
D
Disconnect the No. 1 junction connector.
| *1 | DLC3 |
| *a | Front view of wire harness connector
(to No. 1 Junction Connector) |
| *b | to Main Body ECU (Multiplex Network Body ECU) |
| *c | to Pre-crash Safety City Sensor |
| *d | to No. 2 Junction Connector |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| F82-1 (CANH) - F4-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Main body ECU (Multiplex network body ECU) |
| F82-12 (CANL) - F4-16 (BAT) | |||
| F82-2 (CANH) - F4-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Pre-crash Safety City Sensor |
| F82-13 (CANL) - F4-16 (BAT) | |||
| F82-4 (CANH) - F4-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | No. 2 junction connector |
| F82-15 (CANL) - F4-16 (BAT) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (No. 2 junction connector main line) | B |
| NG (ECU or sensor bus line) | C |
A
B
C
Disconnect the No. 1 junction connector.
| *1 | DLC3 |
| *a | Front view of wire harness connector
(to No. 1 Junction Connector) |
| *b | to ECM |
| *c | to Skid Control ECU (Brake Actuator Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| A61-9 (CANH) - F4-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | ECM |
| A61-20 (CANL) - F4-16 (BAT) | |||
| A61-10 (CANH) - F4-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Skid control ECU (Brake actuator assembly) |
| A61-21 (CANL) - F4-16 (BAT) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (ECU or sensor bus line) | B |
A
B
Reconnect all wire harness connectors (No. 1 junction connector and No. 2 junction connector).
Disconnect the ECU or sensor connected to the CAN bus line that is shorted to +B.
If the ECU or sensor has multiple connectors, disconnect the connector that includes the CAN bus lines. To determine the ECU or sensor that is connected to the shorted bus line, refer to the terminals of ECU tables (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(w/ Toyota Safety Sense)>TERMINALS OF ECU).
| *1 | DLC3 |
| *a | Component with harness connected
(Central Gateway ECU (Network Gateway ECU)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F139-18 (CA4H) - F4-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| F139-17 (CA4L) - F4-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
If the resistance changes to 6 kΩ or higher when the connector is disconnected from the ECU (or sensor), there may be a short in the ECU (or sensor).
OK
NG