Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(w/ Toyota Safety Sense) › from 2017.01
RM19S0E _57 Power Source / Network _051489 NETWORKING _0307623 CAN COMMUNICATION SYSTEM(w/ Toyota Safety Sense) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Toyota Safety Sense)  Check Bus 2 Line for Short to GND  


DESCRIPTION

There may be a short circuit between one of the CAN bus lines and GND when there is no resistance between terminal 18 (CA4H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 17 (CA4L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3.

Symptom Trouble Area
No resistance exists between terminal 18 (CA4H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 17 (CA4L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3.
·

Short to ground in CAN main bus line

·

Short to ground in CAN branch line

·

ECM

·

Combination meter assembly

·

Airbag sensor assembly

·

Skid control ECU (brake actuator assembly)

·

Main body ECU (multiplex network body ECU)

·

Power steering ECU assembly

·

Steering angle sensor (spiral cable sub-assembly)

·

Air conditioning amplifier assembly

·

Pre-crash safety city sensor

·

No. 1 junction connector

·

No. 2 junction connector



WIRING DIAGRAM

E351547E02
1.292,0.531 1.906,0.729 0.615,0.198 10 false CA4H 1.292,1.094 1.906,1.292 0.615,0.198 10 false CA4L 1.271,2.677 1.885,2.875 0.615,0.198 10 false CANH 1.281,3.24 1.896,3.438 0.615,0.198 10 false CANL 1.26,4.708 1.875,4.906 0.615,0.198 10 false CANH 1.281,5.26 1.896,5.458 0.615,0.198 10 false CANL 0.302,1.448 0.917,1.646 0.615,0.198 10 false F139 0.302,1.615 2.281,2.052 1.979,0.438 10 false Central Gateway ECU (Network Gateway ECU) 0.438,3.594 2.021,4.042 1.583,0.448 10 false Air Conditioning Amplifier Assembly 0.333,5.76 2.302,6.135 1.969,0.375 10 false Power Steering ECU Assembly 0.333,5.594 0.813,5.802 0.479,0.208 10 false F6 1.802,0.438 2.115,0.635 0.313,0.198 10 false 18 1.802,1 2.115,1.198 0.313,0.198 10 false 17 1.823,2.479 2.135,2.677 0.313,0.198 10 false 11 1.823,3.042 2.135,3.24 0.313,0.198 10 false 12 1.823,2.885 2.135,3.083 0.313,0.198 10 false *1 1.823,3.448 2.135,3.646 0.313,0.198 10 false *1 2.229,2.479 2.542,2.677 0.313,0.198 10 false 8 2.229,3.042 2.542,3.24 0.313,0.198 10 false 9 2.177,2.875 2.49,3.073 0.313,0.198 10 false *2 2.177,3.448 2.49,3.646 0.313,0.198 10 false *2 1.792,2.677 2.104,2.875 0.313,0.198 10 false F42 1.792,3.24 2.104,3.438 0.313,0.198 10 false F42 2.146,3.24 2.458,3.438 0.313,0.198 10 false F41 2.146,2.677 2.458,2.875 0.313,0.198 10 false F41 1.802,5.156 2.115,5.354 0.313,0.198 10 false 8 1.802,4.594 2.115,4.792 0.313,0.198 10 false 7 2.917,5.156 3.229,5.354 0.313,0.198 10 false 17 2.99,4.594 3.302,4.792 0.313,0.198 10 false 6 2.917,3.146 3.229,3.344 0.313,0.198 10 false 19 2.99,2.583 3.302,2.781 0.313,0.198 10 false 8 2.917,1 3.229,1.198 0.313,0.198 10 false 20 2.99,0.438 3.302,0.635 0.313,0.198 10 false 9 3.198,7.573 3.51,7.771 0.313,0.198 10 false 21 3.969,7.573 4.281,7.771 0.313,0.198 10 false 10 4.219,6.406 4.531,6.604 0.313,0.198 10 false F83 4.219,6.573 6.094,6.823 1.875,0.25 10 false No. 2 Junction Connector 5.135,5.604 5.729,5.823 0.594,0.219 10 false F30 5.135,5.771 7.01,6.24 1.875,0.469 10 false Steering Angle Sensor (Spiral Cable Sub-assembly) 5.26,3.563 5.854,3.781 0.594,0.219 10 false F16 5.271,3.729 7.021,4.021 1.75,0.292 10 false Airbag Sensor Assembly 5.135,1.583 7.094,1.896 1.958,0.313 10 false Combination Meter Assembly 5.125,1.417 5.719,1.635 0.594,0.219 10 false F1 4.219,0.438 4.531,0.635 0.313,0.198 10 false 7 4.219,1 4.531,1.198 0.313,0.198 10 false 18 5.354,0.438 5.667,0.635 0.313,0.198 10 false 32 5.354,1 5.667,1.198 0.313,0.198 10 false 31 5.354,2.583 5.667,2.781 0.313,0.198 10 false 13 5.354,3.146 5.667,3.344 0.313,0.198 10 false 22 4.219,2.583 4.531,2.781 0.313,0.198 10 false 4 4.219,3.146 4.531,3.344 0.313,0.198 10 false 15 4.219,4.594 4.531,4.792 0.313,0.198 10 false 1 4.219,5.156 4.531,5.354 0.313,0.198 10 false 12 5.427,4.594 5.74,4.792 0.313,0.198 10 false 4 5.427,5.156 5.74,5.354 0.313,0.198 10 false 3 5.656,4.698 6.271,4.896 0.615,0.198 10 false CANH 5.656,5.26 6.271,5.458 0.615,0.198 10 false CANL 5.656,2.677 6.271,2.875 0.615,0.198 10 false CANH 5.646,0.438 6.26,0.635 0.615,0.198 10 false CANH 5.656,3.24 6.271,3.438 0.615,0.198 10 false CANL 5.656,1 6.271,1.198 0.615,0.198 10 false CANL 6.177,0.833 6.792,1.031 0.615,0.198 10 false 120Ω 0.25,7.417 3.083,7.74 2.833,0.323 10 false *2: for Manual Air Conditioning System 0.25,7.063 3.083,7.385 2.833,0.323 10 false *1: for Automatic Air Conditioning System

E351548E01
1.208,1.083 1.823,1.281 0.615,0.198 10 false CA1P 1.208,1.646 1.823,1.844 0.615,0.198 10 false CA1N 1.188,4.167 1.802,4.365 0.615,0.198 10 false CANH 1.198,4.729 1.813,4.927 0.615,0.198 10 false CANL 0.667,4.552 1.281,4.75 0.615,0.198 10 false 120Ω 0.646,2 1.26,2.198 0.615,0.198 10 false L11 0.635,2.167 1.688,2.615 1.052,0.448 10 false Pre-crash Safety City Sensor 0.948,5.177 1.563,5.375 0.615,0.198 10 false A83 0.948,5.344 1.563,5.542 0.615,0.198 10 false ECM 1.719,0.99 1.969,1.188 0.25,0.198 10 false 5 1.719,1.542 1.969,1.74 0.25,0.198 10 false 11 1.719,4.167 1.969,4.365 0.25,0.198 10 false 13 1.719,4.729 1.969,4.927 0.25,0.198 10 false 26 2.792,1.083 3.094,1.26 0.302,0.177 10 false F82 2.792,1.646 3.094,1.823 0.302,0.177 10 false F82 3.219,0.802 3.521,0.979 0.302,0.177 10 false F82 3.74,0.802 4.042,0.979 0.302,0.177 10 false F82 4.104,1.083 4.406,1.26 0.302,0.177 10 false A61 4.115,4.833 4.417,5.01 0.302,0.177 10 false F82 4.115,4.271 4.417,4.448 0.302,0.177 10 false F82 4.104,1.646 4.406,1.823 0.302,0.177 10 false A61 2.792,4.271 3.094,4.448 0.302,0.177 10 false A61 2.792,4.833 3.094,5.01 0.302,0.177 10 false A61 3.146,0.615 3.396,0.813 0.25,0.198 10 false 15 3.885,0.615 4.135,0.813 0.25,0.198 10 false 4 2.875,0.896 3.125,1.094 0.25,0.198 10 false 2 2.833,1.448 3.083,1.646 0.25,0.198 10 false 13 2.833,4.646 3.083,4.844 0.25,0.198 10 false 20 2.875,4.083 3.125,4.281 0.25,0.198 10 false 9 4.156,0.896 4.406,1.094 0.25,0.198 10 false 10 4.156,1.448 4.406,1.646 0.25,0.198 10 false 21 5.271,0.99 5.521,1.188 0.25,0.198 10 false 25 5.271,1.552 5.521,1.75 0.25,0.198 10 false 14 4.188,4.083 4.438,4.281 0.25,0.198 10 false 1 4.156,4.646 4.406,4.844 0.25,0.198 10 false 12 5.271,4.167 5.521,4.365 0.25,0.198 10 false 14 5.271,4.729 5.521,4.927 0.25,0.198 10 false 13 5.573,1.083 6.188,1.281 0.615,0.198 10 false CANH 5.573,4.271 6.188,4.469 0.615,0.198 10 false CANH 5.573,1.646 6.188,1.844 0.615,0.198 10 false CANL 5.573,4.833 6.188,5.031 0.615,0.198 10 false CANL 4.188,3.021 5.948,3.271 1.76,0.25 10 false No. 1 Junction Connector 5.219,2.135 6.792,2.615 1.573,0.479 10 false Skid Control ECU (Brake Actuator Assembly) 5.219,1.969 5.833,2.167 0.615,0.198 10 false A55 5.146,5.313 6.833,5.771 1.688,0.458 10 false Main Body ECU (Multiplex Network Body ECU) 5.146,5.146 5.76,5.344 0.615,0.198 10 false F76

CAUTION / NOTICE / HINT

NOTICE:
·

Turn the ignition switch off before measuring the resistances of the CAN main wire and the CAN branch wire.

·

After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not in operation.

·

Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.



HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 2 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the No. 2 junction connector.


c.
U161114C03
1.552,1.531 0.833,0.813 true 1.771,1.542 1.052,0.635 true 1.177,1.552 0.708,1.438 true 1.167,1.698 0.76,1.698 true 1.885,1.531 2.552,0.604 true 2.01,1.531 2.552,0.875 true 2.24,1.531 2.583,1.417 true 1.552,1.75 0.813,2.302 true 1.896,1.75 2.573,2.615 true 2.01,1.75 2.573,2.365 true 2.25,1.75 2.583,1.833 true 1.781,1.76 1.042,2.531 true 2.135,1.531 2.583,1.167 true 2.125,1.74 2.583,2.083 true 1.635,3.271 1.208,2.906 true 1.667,0.208 2.021,0.438 0.354,0.229 10 false F83 1.708,2.49 1.969,2.656 0.26,0.167 10 false F4 0.104,0.063 0.615,0.396 0.51,0.333 10 false *a 0.958,2.833 1.302,3 0.344,0.167 10 false CG 0.156,1.333 0.708,1.49 0.552,0.156 10 false CANH*b 0.198,1.604 0.729,1.76 0.531,0.156 10 false CANL*b 0.104,2.688 0.323,2.865 0.219,0.177 10 false *1 0.302,0.708 0.875,0.896 0.573,0.188 10 false CANH*c 0.51,0.521 1.104,0.667 0.594,0.146 10 false CANH*d 2.583,0.5 3.146,0.677 0.563,0.177 10 false CANH*e 2.583,0.771 3.135,0.927 0.552,0.156 10 false CANH*f 2.656,1.313 3.271,1.552 0.615,0.24 10 false CANH*h 0.281,2.229 0.823,2.385 0.542,0.156 10 false CANL*c 0.51,2.458 1.042,2.625 0.531,0.167 10 false CANL*d 2.604,2.51 3.135,2.698 0.531,0.188 10 false CANL*e 2.604,2.271 3.188,2.417 0.583,0.146 10 false CANL*f 2.656,1.729 3.25,1.969 0.594,0.24 10 false CANL*h 2.656,1.063 3.25,1.25 0.594,0.188 10 false CANH*g 2.656,1.979 3.25,2.167 0.594,0.188 10 false CANL*g
*1 DLC3
*a Front view of wire harness connector
(to No. 2 Junction Connector)
*b to Steering Angle Sensor (Spiral Cable Sub-assembly)
*c to Airbag Sensor Assembly
*d to Power Steering ECU Assembly
*e to Combination Meter Assembly
*f to Air Conditioning Amplifier Assembly
*g to Central Gateway ECU (Network Gateway ECU)
*h to No. 1 Junction Connector


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F83-1 (CANH) - F4-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Steering angle sensor (Spiral cable sub-assembly)
F83-12 (CANL) - F4-4 (CG)
F83-4 (CANH) - F4-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Airbag sensor assembly
F83-15 (CANL) - F4-4 (CG)
F83-6 (CANH) - F4-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Power steering ECU assembly
F83-17 (CANL) - F4-4 (CG)
F83-7 (CANH) - F4-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Combination meter assembly
F83-18 (CANL) - F4-4 (CG)
F83-8 (CANH) - F4-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Air conditioning amplifier assembly
F83-19 (CANL) - F4-4 (CG)
F83-9 (CANH) - F4-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Central gateway ECU (network gateway ECU)
F83-20 (CANL) - F4-4 (CG)
F83-10 (CANH) - F4-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher No. 1 junction connector
F83-21 (CANL) - F4-4 (CG)


Result
Result Proceed to
OK A
NG (No. 1 junction connector main line) B
NG (ECU or sensor bus line) C
NG (Central gateway ECU (network gateway ECU) branch line) D



A

REPLACE NO. 2 JUNCTION CONNECTOR

B

2.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 1 JUNCTION CONNECTOR)

C

4.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU, SENSOR)

D

REPAIR OR REPLACE CAN BRANCH LINE CONNECTED TO CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

2.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 1 JUNCTION CONNECTOR)
a.

Disconnect the No. 1 junction connector.


b.
U161116C03
1.188,1.542 0.792,1.385 true 1.177,1.708 0.833,1.708 true 1.552,1.531 2.427,0.948 true 1.552,1.74 2.448,2.354 true 1.615,3.302 1.219,2.906 true 1.313,1.531 0.833,1.063 true 1.313,1.74 0.833,2 true 1.656,0.198 2.01,0.427 0.354,0.229 10 false F82 1.719,2.49 2.198,2.719 0.479,0.229 10 false F4 0.104,0.063 0.615,0.396 0.51,0.333 10 false *a 0.958,2.792 1.313,2.948 0.354,0.156 10 false CG 0.219,1.292 0.792,1.448 0.573,0.156 10 false CANH*b 0.323,1.625 0.875,1.781 0.552,0.156 10 false CANL*b 0.104,2.667 0.313,2.844 0.208,0.177 10 false *1 2.469,0.844 3.073,1.031 0.604,0.188 10 false CANH*d 2.49,2.281 3.104,2.438 0.615,0.156 10 false CANL*d 0.292,0.938 0.917,1.104 0.625,0.167 10 false CANH*c 0.281,1.906 0.896,2.083 0.615,0.177 10 false CANL*c
*1 DLC3
*a Front view of wire harness connector
(to No. 1 Junction Connector)
*b to Main Body ECU (Multiplex Network Body ECU)
*c to Pre-crash Safety City Sensor
*d to No. 2 Junction Connector


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F82-1 (CANH) - F4-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Main body ECU (Multiplex network body ECU)
F82-12 (CANL) - F4-4 (CG)
F82-2 (CANH) - F4-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Pre-crash Safety City Sensor
F82-13 (CANL) - F4-4 (CG)
F82-4 (CANH) - F4-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher No. 2 junction connector
F82-15 (CANL) - F4-4 (CG)


Result
Result Proceed to
OK A
NG (No. 2 junction connector main line) B
NG (ECU or sensor bus line) C



A

3.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 1 JUNCTION CONNECTOR)

B

REPAIR OR REPLACE CAN MAIN BUS LINE (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)

C

4.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU, SENSOR)
3.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 1 JUNCTION CONNECTOR)
a.

Disconnect the No. 1 junction connector.


b.
U161118C03
2.115,1.531 2.552,0.729 true 2.24,1.531 2.552,0.948 true 2.115,1.729 2.573,2.406 true 2.24,1.74 2.573,2.167 true 1.625,3.219 1.177,2.833 true 1.646,0.208 2,0.438 0.354,0.229 10 false A61 1.75,2.469 2.104,2.698 0.354,0.229 10 false F4 0.104,0.063 0.615,0.396 0.51,0.333 10 false *a 0.927,2.708 1.292,2.865 0.365,0.156 10 false CG 2.583,0.615 3.167,0.792 0.583,0.177 10 false CANH*b 2.615,2.323 3.177,2.49 0.563,0.167 10 false CANL*b 0.104,2.667 0.292,2.823 0.188,0.156 10 false *1 2.594,0.844 3.188,1.031 0.594,0.188 10 false CANH*c 2.615,2.083 3.177,2.25 0.563,0.167 10 false CANL*c
*1 DLC3
*a Front view of wire harness connector
(to No. 1 Junction Connector)
*b to ECM
*c to Skid Control ECU (Brake Actuator Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
A61-9 (CANH) - F4-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher ECM
A61-20 (CANL) - F4-4 (CG)
A61-10 (CANH) - F4-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Skid control ECU (Brake actuator assembly)
A61-21 (CANL) - F4-4 (CG)


Result
Result Proceed to
OK A
NG (ECU or sensor bus line) B



A

REPLACE NO. 1 JUNCTION CONNECTOR

B

4.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU, SENSOR)
4.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU, SENSOR)
a.

Reconnect all wire harness connectors (No. 1 junction connector and No. 2 junction connector).


b.

Disconnect the ECU or sensor connected to the CAN bus line that is shorted to ground.

HINT:

If the ECU or sensor has multiple connectors, disconnect the connector that includes the CAN bus lines. To determine the ECU or sensor that is connected to the shorted bus line, refer to the terminals of ECU tables (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(w/ Toyota Safety Sense)>TERMINALS OF ECU).



c.
U161138C03
1.667,1.135 1.073,1.833 true 1.76,1.135 2.365,1.833 true 1.135,2.771 1.615,3.208 true 0.802,1.854 1.344,2.01 0.542,0.156 10 false CA4H 2.156,1.854 2.698,2.01 0.542,0.156 10 false CA4L 0.833,2.667 1.219,2.875 0.385,0.208 10 false CG 1.563,0.271 1.917,0.448 0.354,0.177 10 false F139 1.646,2.573 1.927,2.792 0.281,0.219 10 false F4 0.104,0.073 0.406,0.271 0.302,0.198 10 false *a 0.104,2.563 0.406,2.76 0.302,0.198 10 false *1
*1 DLC3
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F139-18 (CA4H) - F4-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
F139-17 (CA4L) - F4-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher


HINT:

If the resistance changes to 200 Ω or higher when the connector is disconnected from the ECU (or sensor), there may be a short in the ECU (or sensor).




OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BUS LINE OR CONNECTOR