Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(w/ Toyota Safety Sense) › from 2017.01
RM19S0E _57 Power Source / Network _051489 NETWORKING _0307623 CAN COMMUNICATION SYSTEM(w/ Toyota Safety Sense) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Toyota Safety Sense)  Front Camera Module Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Front Camera Module Communication Stop Mode Either condition is met:
·

Communication stop for "Front Camera Module" is indicated on the "Communication Bus Check" screen of the GTS.

(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Front Camera Module Communication Stop Mode" are output.

(Click here)


·

Power source or inside Pre-crash safety city sensor

·

Pre-crash safety city sensor branch wire or connector

·

Pre-crash safety city sensor



WIRING DIAGRAM

C328843E05
1.229,0.719 1.656,0.885 0.427,0.167 10 false CANH 1.229,1.156 1.656,1.323 0.427,0.167 10 false CANL 0.427,1.583 0.833,1.75 0.406,0.167 10 false F82 5.531,0.625 5.74,0.792 0.208,0.167 10 false 5 5.75,0.708 6.177,0.875 0.427,0.167 10 false CA1P 5.75,1.177 6.177,1.344 0.427,0.167 10 false CA1N 5.74,2.958 6.167,3.125 0.427,0.167 10 false GND 5.479,1.073 5.688,1.24 0.208,0.167 10 false 11 1.729,0.625 1.906,0.792 0.177,0.167 10 false 2 1.698,1.083 1.885,1.25 0.188,0.167 10 false 13 2.01,2.198 3.354,2.375 1.344,0.177 10 false from IG1 NO. 1 Relay 5.75,2.208 6.177,2.375 0.427,0.167 10 false IG1 5.531,2.115 5.74,2.281 0.208,0.167 10 false 7 5.479,2.854 5.688,3.021 0.208,0.167 10 false 10 0.417,1.76 2.031,2.083 1.615,0.323 10 false No. 1 Junction Connector 5.625,3.563 6.01,3.729 0.385,0.167 10 false L11 5.625,3.729 6.698,4.188 1.073,0.458 10 false Pre-crash Safety City Sensor 4.167,2.365 5.177,2.604 1.01,0.24 10 false ECU-IG NO. 1

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Turn the ignition switch off before measuring the resistances between CAN bus main wires and between CAN bus branch wires.

·

Turn the ignition switch off before inspecting CAN bus wires for a ground short.

·

After the ignition switch is turned off, check that the key reminder warning system are not operating.

·

Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.

·

If the pre-crash safety city sensor has been replaced, or the windshield glass has been replaced or removed/installed, be sure to perform Recognition Camera/Target Position Memory and Recognition Camera Axis Adjust (See page Vehicle Interior>PRE-CRASH SAFETY>FRONT SENSOR>ADJUSTMENT (SEQUENTIAL RECOGNITION)).



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (PRE-CRASH SAFETY CITY SENSOR BRANCH WIRE)
U161144C03
1.969,1.052 2.5,0.854 true 1.969,1.365 2.5,1.563 true 0.094,0.063 0.458,0.406 0.365,0.344 10 false *a 2.542,1.49 3,1.646 0.458,0.156 10 false CA1N 2.542,0.75 3,0.906 0.458,0.156 10 false CA1P 1.615,0.25 1.917,0.427 0.302,0.177 10 false L11
*a Front view of wire harness connector
(to Pre-crash Safety City Sensor)


a.

Disconnect the pre-crash safety city sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
L11-5 (CA1P) - L11-11 (CA1N) Ignition switch off 54 to 69 Ω




OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (PRE-CRASH SAFETY CITY SENSOR BRANCH WIRE)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
U161145C03
1.792,1.365 1.573,1.781 true 1.313,1.365 1.083,1.781 true 0.094,0.063 0.458,0.406 0.365,0.344 10 false *a 1.365,1.802 1.823,1.958 0.458,0.156 10 false GND 1.615,0.25 1.896,0.427 0.281,0.177 10 false L11 0.927,1.802 1.385,1.958 0.458,0.156 10 false IG1
*a Front view of wire harness connector
(to Pre-crash Safety City Sensor)


a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
L11-7 (IG1) - Body ground Ignition switch ON 11 to 14 V



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L11-10 (GND) - Body ground Always Below 1 Ω




OK

REPLACE PRE-CRASH SAFETY CITY SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR