Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(w/ Toyota Safety Sense) › from 2017.01
RM19S0E _57 Power Source / Network _051489 NETWORKING _0307623 CAN COMMUNICATION SYSTEM(w/ Toyota Safety Sense) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Toyota Safety Sense)  Open in Bus 3 Main Bus Line  


DESCRIPTION

There may be an open circuit in one of the bus 3 main lines when the resistance between terminals 6 (CA3H) and 21 (CA3L) of the central gateway ECU (network gateway ECU) is 70 Ω or higher.

Symptom Trouble Area
Resistance between terminals 6 (CA3H) and 21 (CA3L) of central gateway ECU (network gateway ECU) is 70 Ω or higher.
·

CAN main bus line or connector

·

Central gateway ECU (network gateway ECU)

·

No. 1 junction connector



This malfunction is not related to the lines of a CAN main bus branch or to ECUs or sensors connected a CAN main bus branch.

WIRING DIAGRAM

C346805E24
0.656,4.604 2.604,5.135 1.948,0.531 10 false Central Gateway ECU (Network Gateway ECU) 5.271,4.542 6.938,4.781 1.667,0.24 10 false No. 1 Junction Connector 0.958,1.323 1.729,1.521 0.771,0.198 10 false 120 Ω 0.969,3.771 1.74,3.969 0.771,0.198 10 false 120 Ω 1.563,0.979 2.177,1.177 0.615,0.198 10 false CA3H 1.583,1.458 2.198,1.656 0.615,0.198 10 false CA3L 1.563,3.427 2.177,3.625 0.615,0.198 10 false CAYH 1.594,3.906 2.208,4.104 0.615,0.198 10 false CAYL 2.125,0.969 2.281,1.167 0.156,0.198 10 false 6 2.094,1.458 2.406,1.656 0.313,0.198 10 false 21 2.083,3.406 2.396,3.604 0.313,0.198 10 false 19 2.083,3.885 2.396,4.083 0.313,0.198 10 false 20 5.313,0.948 5.469,1.146 0.156,0.198 10 false 9 5.271,1.417 5.583,1.615 0.313,0.198 10 false 20 5.271,3.427 5.552,3.677 0.281,0.25 10 false 11 5.281,3.885 5.594,4.083 0.313,0.198 10 false 22 0.667,4.427 1.125,4.625 0.458,0.198 10 false F139 5.271,4.375 5.729,4.573 0.458,0.198 10 false F82

CAUTION / NOTICE / HINT

NOTICE:
·

Turn the ignition switch off before measuring the resistances of the CAN main wire and the CAN branch wire.

·

After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not in operation.

·

Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.



HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Remove the central gateway ECU (network gateway ECU) (See page Power Source / Network>NETWORKING>NETWORK GATEWAY ECU>REMOVAL).


b.
U161127C02
1.125,0.958 0.833,0.573 true 2.354,1.604 1.552,1.219 true 1.708,1.604 1.417,1.219 true 0.927,1.594 1.219,1.208 true 0.146,0.063 0.323,0.229 0.177,0.167 10 false *a 0.427,0.479 0.875,0.635 0.448,0.156 10 false CA3H 1.552,0.281 1.969,0.5 0.417,0.219 10 false F139 0.646,1.625 1.094,1.781 0.448,0.156 10 false CA3L 2.198,1.625 2.646,1.781 0.448,0.156 10 false CAYH 1.531,1.625 1.979,1.781 0.448,0.156 10 false CAYL
*a Component without harness connected
(Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F139-6 (CA3H) - F139-21 (CA3L) Always 108 to 132 Ω
F139-19 (CAYH) - F139-20 (CAYL) Always 108 to 132 Ω




OK

2.CHECK FOR OPEN IN CAN BUS LINES (NO. 1 JUNCTION CONNECTOR)

NG

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

2.CHECK FOR OPEN IN CAN BUS LINES (NO. 1 JUNCTION CONNECTOR)
a.

Reinstall the central gateway ECU (network gateway ECU) (See page Power Source / Network>NETWORKING>NETWORK GATEWAY ECU>INSTALLATION).


b.

Disconnect the cable from the negative (-) battery terminal.


c.
U161125C02
2.104,1.323 2.688,0.76 true 2.344,1.333 2.656,1.104 true 1.729,1.896 2.052,1.542 true 2.656,1.896 2.333,1.542 true 0.365,1.313 0.719,1.49 0.354,0.177 10 false F82 2.75,0.646 3.344,0.802 0.594,0.156 10 false CANH*c 2.74,1 3.333,1.156 0.594,0.156 10 false CANH*b 1.219,1.865 1.813,2.021 0.594,0.156 10 false CANL*c 2.698,1.896 3.292,2.052 0.594,0.156 10 false CANL*b 0.115,0.083 0.323,0.292 0.208,0.208 10 false *a
*a Front view of wire harness connector
(to No. 1 Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU) (CA3H and CA3L Terminal)
*c to Central Gateway ECU (Network Gateway ECU) (CAYH and CAYL Terminal)


Disconnect the No. 1 junction connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F82-9 (CANH) - F82-20 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU) (CA3H and CA3L terminal)
F82-11 (CANH) - F82-22 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU) (CAYH and CAYL terminal)




OK

REPLACE NO. 1 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 1 JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))