Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(w/ Toyota Safety Sense) › from 2017.01
RM19S0E _57 Power Source / Network _051489 NETWORKING _0307623 CAN COMMUNICATION SYSTEM(w/ Toyota Safety Sense) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Toyota Safety Sense)  Check Bus 3 Line for Short to GND  


DESCRIPTION

There may be a short circuit between one of the CAN bus lines and GND when there is no resistance between terminal 6 (CA3H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 21 (CA3L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3.

Symptom Trouble Area
No resistance exists between terminal 6 (CA3H) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3, or terminal 21 (CA3L) of the central gateway ECU (network gateway ECU) and terminal 4 (CG) of the DLC3.
·

Short to ground in CAN main bus line

·

Short to ground in CAN branch line

·

Central gateway ECU (network gateway ECU)

·

Radio and display receiver assembly*1

·

Navigation receiver assembly*2

·

No. 1 junction connector



*1: for Radio and Display Type

*2: for Navigation Receiver Type


WIRING DIAGRAM

E351561E01
1.063,0.813 1.677,1.01 0.615,0.198 10 false CA3H 1.094,1.281 1.5,1.49 0.406,0.208 10 false CA3L 3.844,0.813 4.094,1.01 0.25,0.198 10 false 9 3.792,1.281 4.042,1.479 0.25,0.198 10 false 20 3.781,4.938 4.031,5.135 0.25,0.198 10 false 11 3.781,5.427 4.031,5.625 0.25,0.198 10 false 22 1.583,0.813 1.833,1.01 0.25,0.198 10 false 6 1.583,1.292 1.833,1.49 0.25,0.198 10 false 21 1.542,4.917 1.792,5.115 0.25,0.198 10 false 19 1.563,5.417 1.813,5.615 0.25,0.198 10 false 20 1.042,4.938 1.656,5.135 0.615,0.198 10 false CAYH 1.063,5.417 1.677,5.615 0.615,0.198 10 false CAYL 0.51,5.25 1.125,5.448 0.615,0.198 10 false 120 Ω 0.5,1.156 1.115,1.354 0.615,0.198 10 false 120 Ω 0.188,5.896 0.802,6.094 0.615,0.198 10 false F139 0.177,6.052 2.167,6.5 1.99,0.448 10 false Central Gateway ECU (Network Gateway ECU) 3.76,5.844 4.375,6.042 0.615,0.198 10 false F82 3.75,6 5.5,6.25 1.75,0.25 10 false No. 1 Junction Connector 4.896,2.854 5.146,3.052 0.25,0.198 10 false 10 4.896,3.333 5.146,3.531 0.25,0.198 10 false 21 5.51,2.76 5.76,2.958 0.25,0.198 10 false 10 5.906,2.771 6.156,2.969 0.25,0.198 10 false 10 5.563,3.26 5.813,3.458 0.25,0.198 10 false 9 5.927,3.26 6.177,3.458 0.25,0.198 10 false 9 5.448,2.948 5.781,3.146 0.333,0.198 10 false F127 5.813,2.938 6.146,3.135 0.333,0.198 10 false F132 5.823,3.417 6.156,3.615 0.333,0.198 10 false F132 5.458,3.427 5.792,3.625 0.333,0.198 10 false F127 5.51,3.125 5.76,3.323 0.25,0.198 10 false *1 5.542,3.646 5.792,3.844 0.25,0.198 10 false *1 5.906,3.125 6.156,3.323 0.25,0.198 10 false *2 5.927,3.635 6.177,3.833 0.25,0.198 10 false *2 6.24,2.948 6.854,3.146 0.615,0.198 10 false CANH 6.26,3.438 6.875,3.635 0.615,0.198 10 false CANL 5.375,3.958 7.115,4.531 1.74,0.573 10 false Radio and Display Receiver Assembly*1 or Navigation Receiver Assembly*2 4.302,6.479 6.635,6.729 2.333,0.25 10 false *2: for Navigation Receiver Type 1.896,6.458 4.229,6.708 2.333,0.25 10 false *1: for Radio and Display Type

CAUTION / NOTICE / HINT

NOTICE:
·

Turn the ignition switch off before measuring the resistances of the CAN main wire and the CAN branch wire.

·

After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not in operation.

·

Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.



HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 1 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the No. 1 junction connector.


c.
U161131C02
2.24,1.531 2.75,0.917 true 2.115,1.531 2.75,0.5 true 2.375,1.531 2.75,1.25 true 2.24,1.74 2.583,2.25 true 2.115,1.74 2.25,2.417 true 2.375,1.729 2.75,2 true 1.615,3.281 0.969,2.875 true 1.625,0.25 1.969,0.427 0.344,0.177 10 false F136 2.823,0.823 3.417,0.99 0.594,0.167 10 false CANH*c 2.833,1.177 3.427,1.344 0.594,0.167 10 false CANH*d 2.823,0.396 3.417,0.563 0.594,0.167 10 false CANH*b 2.573,2.271 3.167,2.438 0.594,0.167 10 false CANL*c 2.823,1.979 3.417,2.146 0.594,0.167 10 false CANL*d 2.042,2.448 2.635,2.615 0.594,0.167 10 false CANL*b 0.146,0.167 0.427,0.344 0.281,0.177 10 false *a 0.146,2.802 0.427,2.979 0.281,0.177 10 false *1 0.698,2.792 0.958,2.969 0.26,0.177 10 false CG 1.698,2.646 1.958,2.823 0.26,0.177 10 false F4
*1 DLC3
*a Front view of wire harness connector
(to No. 1 Junction Connector)
*b Central Gateway ECU (Network Gateway ECU) (CA3H and CA3L Terminal)
*c to Radio and Display Receiver Assembly (for Radio and Display Type) or Navigation Receiver Assembly (for Navigation Receiver Type)
*d Central Gateway ECU (Network Gateway ECU) (CAYH and CAYL Terminal)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F82-9 (CANH) - F4-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Central gateway ECU (network gateway ECU) (CA3H and CA3L terminal)
F82-20 (CANL) - F4-4 (CG)
F82-10 (CANH) - F4-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Radio and display receiver assembly*1 or Navigation receiver assembly*2
F82-21 (CANL) - F4-4 (CG)
F82-11 (CANH) - F4-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher Central gateway ECU (network gateway ECU) (CAYH and CAYL terminal)
F82-22 (CANL) - F4-4 (CG)


*1: for Radio and Display Type

*2: for Navigation Receiver Type


Result
Result Proceed to
OK A
NG (ECU or sensor bus line) B



A

REPLACE NO. 1 JUNCTION CONNECTOR

B

2.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU, SENSOR)
2.CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU, SENSOR)
a.

Reconnect all wire harness connectors (No. 1 junction connector).


b.

Disconnect the ECU or sensor connected to the CAN bus line that is shorted to ground.

HINT:

If the ECU or sensor has multiple connectors, disconnect the connector that includes the CAN bus lines. To determine the ECU or sensor that is connected to the shorted bus line, refer to the terminals of ECU tables (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(w/ Toyota Safety Sense)>TERMINALS OF ECU).



c.
U161136C02
1.375,0.979 0.802,0.51 true 1.438,1.135 0.802,1.833 true 1,2.771 1.615,3.198 true 0.302,0.427 0.844,0.583 0.542,0.156 10 false CA3H 0.302,1.729 0.844,1.885 0.542,0.156 10 false CA3L 0.688,2.677 1.073,2.885 0.385,0.208 10 false CG 1.521,0.25 1.917,0.417 0.396,0.167 10 false F139 1.635,2.563 1.948,2.75 0.313,0.188 10 false F4 0.104,0.073 0.406,0.271 0.302,0.198 10 false *a 0.104,2.563 0.406,2.76 0.302,0.198 10 false *1
*1 DLC3
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F139-6 (CA3H) - F4-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
F139-21 (CA3L) - F4-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher


HINT:

If the resistance changes to 200 Ω or higher when the connector is disconnected from the ECU (or sensor), there may be a short in the ECU (or sensor).




OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BUS LINE OR CONNECTOR