Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor) › from 2017.01
RM19S0E _58 Vehicle Interior _051495 SUPPLEMENTAL RESTRAINT SYSTEMS _0248314 AIRBAG SYSTEM(w/ VSC/Built-in Type Yaw Rate Sensor) J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(w/ VSC/Built-in Type Yaw Rate Sensor)  TC and CG Terminal Circuit  


DESCRIPTION

DTC output mode is set by connecting terminals TC and CG of the DLC3.

The DTCs are displayed by blinking the SRS warning light.

HINT:
·

Make sure that DTCs which relate to the CAN communication system are not output. If any of these DTCs are output, check the CAN communication system.


·

When a warning light keeps blinking, a short to ground in the wiring of terminal TC of the DLC3 or an internal ground short in an ECU is suspected.

·

The DTC output mode signal is transmitted through the CAN to each ECU including the airbag sensor assembly. Thus if no systems enter DTC output mode, the ECM may have a malfunction.



WIRING DIAGRAM

C243297E21
0.552,1.979 0.917,2.208 0.365,0.229 10 false A83 0.552,2.146 0.938,2.385 0.385,0.24 10 false ECM 5.604,3.542 5.792,3.698 0.188,0.156 10 false F4 5.604,3.698 6,3.865 0.396,0.167 10 false DLC3 5.604,1.5 5.865,1.667 0.26,0.167 10 false F16 5.604,1.677 7.156,1.854 1.552,0.177 10 false Airbag Sensor Assembly 1.188,4.344 2.958,4.51 1.771,0.167 10 false : CAN Communication Line 5.49,2.917 5.594,3.094 0.104,0.177 10 false 4 5.406,2.552 5.583,2.729 0.177,0.177 10 false 13 5.667,3.01 5.896,3.177 0.229,0.167 10 false CG 5.667,2.646 5.885,2.802 0.219,0.156 10 false TC 1.094,1.531 1.323,1.698 0.229,0.167 10 false TC 1.385,1.427 1.615,1.625 0.229,0.198 10 false 23

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (DLC3 - ECM)
a.

Turn the ignition switch off.


b.

Disconnect the connector from the ECM.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F4-13 (TC) -
A83-23 (TC)
Always Below 1 Ω




OK

2.CHECK HARNESS AND CONNECTOR (CG OF DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (CG OF DLC3 - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F4-4 (CG) -
Body ground
Always Below 1 Ω




OK

3.CHECK HARNESS AND CONNECTOR (TC OF ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (TC OF ECM)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A83-23 (TC) -
Body ground
Always 1 MΩ or higher




OK

4.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE ECM
a.

Replace the ECM.


b.

Check for DTCs of the ECM.


Result
Result Proceed to
Normal code is output A
DTC is output (for 1NZ-FE) B
DTC is output (for 2NZ-FE) C
DTC output mode is set (except airbag sensor assembly) E



A

END (ECM WAS DEFECTIVE)

B

C

D