Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › from 2017.01
RM19S0E _54 Brake _051475 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0248226 ANTI-LOCK BRAKE SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  ABS Warning Light Remains ON  


DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter via CAN communication.

If any of the following is detected, the ABS warning light remains on:

·

The skid control ECU connectors are disconnected from the brake actuator assembly.

·

There is a malfunction in the skid control ECU (brake actuator assembly) internal circuit.

·

There is an open in the harness between the combination meter and the skid control ECU (brake actuator assembly).

·

The ABS control system is defective.


HINT:

In some cases, the intelligent tester cannot be used when the skid control ECU (brake actuator assembly) is abnormal.


WIRING DIAGRAM

C243294E02
0.87,1.178 1.210,1.317 0.340,0.140 10 CPU 1.744,0.671 2.276,0.810 0.532,0.140 10 CAN I/F 1.038,1.853 1.358,1.991 0.321,0.138 10 ABS 1.773,2.423 1.949,2.579 0.176,0.156 10 IG 0.577,2.748 2.421,2.912 1.843,0.164 10 Combination Meter Assembly 3.875,2.443 4.811,2.603 0.936,0.160 10 ECU-IG NO. 2 5.663,1.421 5.762,1.577 0.099,0.156 10 1 5.845,1.516 6.262,1.667 0.417,0.152 10 GND1 5.585,2.212 5.778,2.368 0.193,0.156 10 34 5.849,2.324 6.095,2.480 0.246,0.156 10 IG1 5.456,2.747 7.141,3.107 1.684,0.360 10 Skid Control ECU (Brake Actuator Assembly) 5.456,2.563 5.729,2.713 0.272,0.150 10 A55 1.165,3.349 2.893,3.493 1.729,0.144 10 : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU(brake actuator assembly) connector is securely connected.

OK:

The connector is securely connected.




OK

2.CHECK CAN COMMUNICATION SYSTEM

NG

CONNECT CONNECTOR TO ECU CORRECTLY

2.CHECK CAN COMMUNICATION SYSTEM
a.

Result
Result Proceed to
DTC is not output A
DTC is output B


A

3.INSPECT BATTERY

B

3.INSPECT BATTERY
a.

Check the battery voltage.

Standard voltage:

11 to 14 V


Result
Result Proceed to
OK A
NG (for 1NZ-FE) B
NG (for 2NZ-FE) C



A

4.CHECK TERMINAL VOLTAGE (IG1 TERMINAL)

B

C

4.CHECK TERMINAL VOLTAGE (IG1 TERMINAL)
a.

Disconnect the skid control ECU (brake actuator assembly) connector.


b.

Turn the ignition switch to ON.


c.
U158340E01
1.625,0.133 1.920,0.314 0.295,0.181 10 A55 0.125,0.109 0.316,0.272 0.191,0.163 10 *a 2.074,1.924 2.326,2.062 0.252,0.137 10 IG1 2.297,1.324 2.197,1.907 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage :
Tester Connection Switch Condition Specified Condition
A55-34 (IG1) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid control ECU)


d.

Turn the ignition switch off.



OK

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.
U158341E01
1.625,0.133 1.920,0.314 0.295,0.181 10 A55 0.125,0.109 0.316,0.272 0.191,0.163 10 *a 0.018,0.935 0.437,1.072 0.419,0.137 10 GND1 1.151,0.998 0.535,1.037 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance :
Tester Connection Condition Specified Condition
A55-1 (GND1) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Skid control ECU)


b.

Reconnect the skid control ECU (brake actuator assembly) connector.



OK

6.READ VALUE USING GTS (ABS WARNING LIGHT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)

6.READ VALUE USING GTS (ABS WARNING LIGHT)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


e.

According to the display on the GTS, read the Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
ABS Warning Light ABS warning light / OFF or ON OFF -


f.

When performing the ABS Warning Light Active Test, check ABS Warning Light in the Data List.


ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
ABS Warning Light ABS warning light Warning light ON/OFF Observe the combination meter.

Result
Result Proceed to
Data List Display Data List Display when Performing Active Test ON/OFF Operation
ON Changes between ON and OFF A
Does not change between ON and OFF B
OFF Changes between ON and OFF A
Does not change between ON and OFF B


A

7.REPLACE COMBINATION METER ASSEMBLY

B

7.REPLACE COMBINATION METER ASSEMBLY
a.

Turn the ignition switch off.


b.

Replace the combination meter assembly (See page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL).



NEXT

8.CHECK COMBINATION METER ASSEMBLY
8.CHECK COMBINATION METER ASSEMBLY
a.

Connect the GTS to the DLC3.


b.

Perform Active Test of the combination meter assembly using the GTS (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).

OK:

The ABS warning light turns on or off in accordance with the GTS.


Result
Result
OK
NG



OK

END

NG