Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor) › from 2017.01
RM19S0E _54 Brake _051475 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0248235 VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)  C1232  Acceleration Sensor Stuck Malfunction  C1243  Acceleration Sensor Stuck Malfunction  C1245  Acceleration Sensor Output Malfunction  C1279  Acceleration Sensor Output Voltage Malfunction (Test Mode DTC)  C1473  Yaw Rate Sensor (Test Mode DTC)  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives signals from the yaw rate and deceleration sensor (yaw rate sensor) via the CAN communication system.

The yaw rate and deceleration sensor (yaw rate sensor) has a built in deceleration sensor and detects the vehicle's condition using 2 circuits (GL1, GL2). If there is trouble in the bus lines between the yaw rate and deceleration sensor (yaw rate sensor) and the CAN communication system, the DTCs U0123 (Lost Communication with Yaw Rate Sensor Module) and U0124 (Lost Communication with Lateral Acceleration Sensor Module) are output.

These DTCs are also output when calibration has not been completed.

DTCs C1279 and C1473 can be cleared when the yaw rate and deceleration sensor (yaw rate sensor) sends a yaw rate and/or deceleration signal or the Test Mode ends. DTCs C1279 and C1473 are output only in the Test Mode.

DTC No. DTC Detection Condition Trouble Area
C1232 At a vehicle speed of 10 km/h (6 mph) or more, either GL1 or GL2 (input signal) does not change for 30 seconds or more.
·

Yaw rate and deceleration sensor (Yaw rate sensor)

·

Yaw rate and deceleration sensor (Yaw rate sensor) circuit


C1243 While the vehicle speed changes from 30 km/h (19 mph) to 0 km/h (0 mph), the condition that the values of GL1 and GL2 do not change 0.0294 G or more occurs 16 times or more.
·

Yaw rate and deceleration sensor (Yaw rate sensor)

·

Yaw rate and deceleration sensor (Yaw rate sensor) circuit


C1245 At a vehicle speed of 30 km/h (19 mph) or more, the difference between the forward and backward G calculated from the acceleration sensor value and that calculated from the vehicle speed exceeds 0.35 G for 60 seconds or more.
·

Yaw rate and deceleration sensor (Yaw rate sensor)

·

Yaw rate and deceleration sensor (Yaw rate sensor) circuit

·

Sensor installation


C1279 Detected only during Test Mode.
·

Yaw rate and deceleration sensor (Yaw rate sensor)

·

Sensor installation


C1473 Detected only during Test Mode. Yaw rate and deceleration sensor (Yaw rate sensor)

WIRING DIAGRAM

C248747E03
5.208,3.323 6.771,3.75 1.563,0.427 10 false Skid Control ECU (Brake Actuator Assembly) 0.708,4.167 2.385,4.344 1.677,0.177 10 false : CAN Communication line 2.531,1.896 3.583,2.052 1.052,0.156 10 false ECU-IG NO. 1 1,1.75 1.271,1.906 0.271,0.156 10 false IG 1.26,1.625 1.438,1.781 0.177,0.156 10 false 4 1.26,2.594 1.438,2.75 0.177,0.156 10 false 1 0.875,2.688 1.271,2.844 0.396,0.156 10 false GND 0.26,3.531 2.427,3.979 2.167,0.448 10 false Yaw Rate and Deceleration Sensor (Yaw Rate Sensor) 0.26,3.354 0.635,3.531 0.375,0.177 10 false F122

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the brake actuator assembly, perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:

When DTC U0123, U0124 and/or U0126 is output together with DTC C1232, C1243 and/or C1245, inspect and repair the trouble areas indicated by DTC U0123, U0124 and/or U0126 first (See Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)>U0073page ).


PROCEDURE

1.CHECK DTC

b.

At a speed of 30 km/h (19 mph) or more, drive the vehicle, turn the steering wheel, and decelerate (depress the brake pedal) the vehicle.



d.

Check if DTCs for zero point calibration of the yaw rate sensor undone (C1210) or for zero point calibration of the deceleration sensor undone (C1336) are output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC (relating to yaw rate and deceleration sensor) is output A
DTC (relating to CAN communication system) is output B
DTC (C1210 and/or C1336) are output C



A

2.CHECK YAW RATE AND DECELERATION SENSOR (YAW RATE SENSOR) INSTALLATION

B

C

2.CHECK YAW RATE AND DECELERATION SENSOR (YAW RATE SENSOR) INSTALLATION
a.

Turn the ignition switch off.


b.

Check that the yaw rate and deceleration sensor (yaw rate sensor) has been installed properly (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>YAW RATE AND DECELERATION SENSOR>INSTALLATION).

OK:

The sensor should be tightened to the specified torque.

The sensor should not be tilted.




OK

REPLACE YAW RATE AND DECELERATION SENSOR (YAW RATE SENSOR)

NG

INSTALL YAW RATE AND DECELERATION SENSOR (YAW RATE SENSOR) CORRECTLY