Steering angle sensor signals are sent to the skid control ECU (brake actuator assembly) via the CAN communication system. When there is a malfunction in the CAN communication system, it will be detected by the steering angle sensor zero point malfunction diagnostic function.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| C1434 | Normal communication between the skid control ECU and the steering angle sensor and abnormal steering angle sensor zero point. | ·
Steering angle sensor power supply ·
Steering angle sensor (Spiral cable sub-assembly) ·
Skid control ECU (Brake actuator assembly) |
Refer to DTC C1432 (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)>C1432).
Do not remove the steering sensor from the spiral cable sub-assembly.
When replacing the spiral cable sub-assembly, confirm that the replacement part is of the correct specification.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
When DTC U0073, U0123, U0124 and/or U0126 is output together with DTC C1434, inspect and repair the trouble areas indicated by DTC U0073, U0123, U0124 and/or U0126 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)>U0073).
When the speed sensor or the yaw rate and deceleration sensor (yaw rate sensor) has trouble, DTCs for the steering angle sensor (spiral cable sub-assembly) may be output even when the steering angle sensor is normal. When DTCs for the speed sensor or yaw rate and deceleration sensor (yaw rate sensor) are output together with DTCs for the steering angle sensor (spiral cable sub-assembly), inspect and repair the speed sensor and yaw rate and deceleration sensor (yaw rate sensor) first, and then inspect and repair the steering angle sensor (spiral cable sub-assembly).
Turn the ignition switch off.
Turn the ignition switch to ON again and check that no CAN communication system DTC is output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(w/o Toyota Safety Sense)>DIAGNOSIS SYSTEM).
Start the engine.
Drive the vehicle and turn the steering wheel to the right and left at a speed of 35 km/h (22 mph) and check that no speed sensor or yaw rate and acceleration sensor DTCs are output (See pageBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)>DIAGNOSTIC TROUBLE CODE CHART )
| Result | Proceed to |
|---|---|
| No CAN communication system, speed sensor, or yaw rate and acceleration sensor DTCs are output | A |
| CAN communication system DTC is output | B |
| Speed sensor or yaw rate and acceleration sensor DTC is output | C |
If there is a malfunction in any of the speed sensors or the yaw rate and deceleration sensor (yaw rate sensor), an abnormal value may be output although the steering angle sensor (spiral cable sub-assembly) sensor is normal.
If speed sensor and yaw rate and deceleration sensor (yaw rate sensor) DTCs are output simultaneously, repair these two sensors first and inspect the steering angle sensor (spiral cable sub-assembly).
A
B
C
OK
NG
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F30-2 (ESS) - Body ground | Always | Below 1 Ω |
If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)>PROBLEM SYMPTOMS TABLE).
| *a | Front view of wire harness connector
(to Steering angle sensor) |
Reconnect the steering angle sensor connector.
Reinstall the steering wheel and the column cover lower.
OK
NG