Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor) › from 2017.01
RM19S0E _54 Brake _051475 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0248235 VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor) J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)  TS and CG Terminal Circuit  


DESCRIPTION

In Test Mode (signal check), a malfunction in the speed sensor that cannot be detected when the vehicle is stopped can be detected while driving.

Sensor check mode can be entered by connecting terminals TS and CG of the DLC3 and turning the ignition switch from off to ON.

WIRING DIAGRAM

C240013E05
0.063,1.854 0.26,2.01 0.198,0.156 10 false F6 0.063,2.01 2.021,2.177 1.958,0.167 10 false Power Steering ECU Assembly 1.104,1.552 1.323,1.708 0.219,0.156 10 false TS 1.396,1.458 1.51,1.604 0.115,0.146 10 false 6 5.385,1.49 6.938,2.031 1.552,0.542 10 false Skid Control ECU (Brake Actuator Assembly) 5.656,2.656 5.854,2.813 0.198,0.156 10 false TS 5.417,2.563 5.594,2.719 0.177,0.156 10 false 12 5.656,3.042 5.896,3.188 0.24,0.146 10 false CG 5.469,2.948 5.563,3.094 0.094,0.146 10 false 4 5.708,3.594 5.917,3.75 0.208,0.156 10 false F4 5.958,3.594 6.354,3.75 0.396,0.156 10 false DLC3 1.198,4.375 2.917,4.521 1.719,0.146 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:

If the power steering ECU assembly or steering column assembly has been replaced, perform the torque sensor zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)>CALIBRATION).


PROCEDURE

2.INSPECT DLC3

A

3.CHECK HARNESS AND CONNECTOR (TS of DLC3 - POWER STEERING ECU ASSEMBLY)

B

5.INSPECT POWER STEERING ECU ASSEMBLY
3.CHECK HARNESS AND CONNECTOR (TS of DLC3 - POWER STEERING ECU ASSEMBLY)
a.

Turn the ignition switch off.


b.

Disconnect the power steering ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F4-12 (TS) - F6-6 (TS) Always Below 1 Ω
F4-12 (TS) - Body ground Always 10 kΩ or higher



d.

Reconnect the power steering ECU connector.



OK

4.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)

OK

5.INSPECT POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT POWER STEERING ECU ASSEMBLY
U126761E01
0.169,0.087 0.473,0.237 0.304,0.151 10 *a 1.946,0.168 2.251,0.318 0.304,0.151 10 CG 1.55,1.839 1.768,1.990 0.217,0.151 10 TS 0.234,1.293 0.442,1.474 0.208,0.181 10 F4 1.678,1.463 1.678,1.814 false 1.694,0.801 1.694,0.251 1.694,0.251 1.893,0.251 false

a.

Turn the ignition switch off.


b.

Using SST, connect terminals TS and CG of the DLC3.


c.

Turn the ignition switch to ON.


d.

Check that the PS warning light is blinking.

Text in Illustration
*a Front view of DLC3


Result
Result Proceed to
The PS warning light is not blinking A
The PS warning light is blinking B


A

CHECK POWER STEERING ECU ASSEMBLY

B