The skid control ECU (brake actuator assembly) receives the signals from the ECM, steering angle sensor (spiral cable sub-assembly), and yaw rate and deceleration sensor (airbag sensor assembly) via the CAN communication system.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| U0073 | When any of the following is detected:
1.
When the IG1 terminal voltage is between 10 and 17.4 V, after the output of data from the skid control ECU (brake actuator assembly) is completed, the sending continues for 5 seconds or more. 2.
The condition that bus OFF state occurs once or more within 0.1 seconds occurs 10 times in succession. (Sent signals cannot be received.) 3.
When the IG1 terminal voltage is between 10 and 17.4 V, a delay in receiving data from the yaw rate sensor and steering angle sensor continues for 1 second or more. 4.
When the IG1 terminal voltage is between 10 and 17.4 V, the following occurs 10 times in succession. -
The condition that a delay in receiving data from the yaw rate sensor and steering angle sensor occurs more than once within 5 seconds. |
CAN communication system |
| U0100 | When the IG1 terminal voltage is between 10 and 17.4 V, and the vehicle speed is 15 km/h (9 mph) or more, data cannot be received by the ECM for 2 seconds or more. | CAN communication system |
| U0124 | When either of the following is detected:
1.
When the IG1 terminal voltage is between 10 and 17.4 V, and the vehicle speed is 7 km/h or more, data from the acceleration sensor cannot be received for 1 second or more. 2.
When the IG1 terminal voltage is between 10 and 17.4 V, the following occurs 10 times in succession. -
The condition that data from the deceleration sensor cannot be received occurs once or more within 5 seconds. |
CAN communication system |
| U0126 | When either of the following is detected:
1.
When the IG1 terminal voltage is between 10 and 17.4 V, data from the steering angle sensor cannot be received for 1 second or more. 2.
When the IG1 terminal voltage is between 10 and 17.4 V, the following occurs 10 times in succession. -
The condition that data from the steering angle sensor cannot be received occurs once or more within 5 seconds. |
CAN communication system |
Using the GTS, check for any momentary interruption in the wire harness and connector corresponding to a DTC (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)>CHECK FOR INTERMITTENT PROBLEMS).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| EFI Communication Open | EFI communication open detection / Normal or Error | Normal: Normal
Error: Momentary interruption |
- |
| Yaw Rate Open | Yaw rate sensor open detection / Normal or Error | Normal: Normal
Error: Momentary interruption |
- |
| Steering Open | Steering sensor open detection / Normal or Error | Normal: Normal
Error: Momentary interruption |
- |
| Result | Proceed to |
|---|---|
| There is a constant open circuit | A |
| There are no momentary interruptions | B |
| There are momentary interruptions | C |
Perform the above inspection before removing the sensor and connector.
A
B
C
Turn the ignition switch off.
Check if each sensor or ECM connector is securely connected.
Each connector is securely connected.
OK
NG
Turn the ignition switch off.
Record the output DTCs (for ABS, VSC, and CAN communication) (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)>DTC CHECK / CLEAR).
If the CAN communication system DTC and the relevant sensor DTCs are output simultaneously, troubleshoot the relevant sensor DTCs (for ABS and VSC) after the CAN communication system returns to normal.
| Result | Proceed to |
|---|---|
| DTC (relating to CAN communication system) is output (w/o Toyota Safety Sense) | A |
| DTC (relating to CAN communication system) is output (w/ Toyota Safety Sense) | B |
| DTC (relating to ABS and/or VSC system) is output | C |
| DTC is not output | D |
A
B
C
D
Turn the ignition switch off.
Repair or replace the harness or connector.
Check for any momentary interruption between the skid control ECU (brake actuator assembly) and each sensor or ECM (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)>CHECK FOR INTERMITTENT PROBLEMS).
Check that there is no momentary interruption.
NEXT
Turn the ignition switch off.
Start the engine.
Drive the vehicle and turn the steering wheel to the right and left at a speed of 15 km/h (9 mph) or more.
Check that no CAN communication system DTC is output.
w/o Toyota Safety Sense: See pagePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(w/o Toyota Safety Sense)>DIAGNOSIS SYSTEM
w/ Toyota Safety Sense: See pagePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(w/ Toyota Safety Sense)>DIAGNOSIS SYSTEM
If ABS and VSC DTCs are output, record them.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC is output (relating to ABS and/or VSC system) | B |
| DTC is output (relating to CAN communication system) (w/o Toyota Safety Sense) | C |
| DTC is output (relating to CAN communication system) (w/ Toyota Safety Sense) | D |
The CAN communication system must be normal when repairing each sensor DTC (for ABS and VSC).
A
B
C
D