Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(w/ Toyota Safety Sense) › from 2017.01
RM19S0E _57 Power Source / Network _051489 NETWORKING _0307623 CAN COMMUNICATION SYSTEM(w/ Toyota Safety Sense) Y

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Toyota Safety Sense)  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

PRECAUTIONS WHEN TROUBLESHOOTING


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

·

If the CAN communication system is malfunctioning, check the contact pressure of the terminals in connectors, as insufficient terminal contact pressure may be the cause.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE

·

Refer to Diagnosis System for the DTCs for the CAN communication system.

·

Refer to troubleshooting of each system if DTCs regarding the CAN communication system are not output.

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



a.

CAN communication DTCs are output for CAN main bus and CAN branch malfunctions as well as for internal malfunctions or power source malfunctions of ECUs or sensors for systems using CAN communication. Therefore, when DTCs for internal malfunctions or power source malfunctions of corresponding systems are output at the same time as CAN communication DTCs, troubleshoot according to the internal malfunction and power source malfunction DTCs.


b.

An open in a branch for ECUs or sensors that are connected to the CAN main bus can be checked by performing a communication bus check using the GTS. (This inspection is possible when all main bus lines are normal.)


c.

If there was a communication error, the probable ECU or sensor for which communication stopped can be determined using the combination of communication DTCs (DTCs that start with U) that are output.


d.

When an open circuit is detected, before disconnecting related connectors for inspection, push in on the connector body to check that the connector is not loose or disconnected.


e.

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
HINT:
·

If the ignition switch can be turned to ON (the power source mode can be changed to ON) when the vehicle is brought in for repair, check for DTCs and check the illumination condition of the indicators in the combination meter assembly and the basic operation of the vehicle (such as steering operation) promptly.

·

Do not turn the ignition switch off until the inspection of the vehicle is finished, as some fail-safe functions are canceled when the ignition switch is turned off.

·

If the ignition switch cannot be turned to ON (the power source mode cannot be changed to ON) when the vehicle is brought in, measure the voltage of the battery. If the voltage is below 11 V, recharge or replace the battery before performing troubleshooting.

·

If the ignition switch cannot be turned to ON even though the battery voltage is normal, repair this malfunction before performing troubleshooting.




Result:
Result
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS
2.CUSTOMER PROBLEM ANALYSIS
HINT:
·

When troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.

·

Ask the customer if the vehicle is/was equipped with additional devices such as a theft deterrent device or monitor. (If equipped, explain the customer that the additional devices will be removed before performing troubleshooting as the malfunction cannot be checked properly.)



a.

It is useful to confirm the symptoms and the conditions in which the vehicle was operating at the time when a malfunction occurred. This helps to narrow down the malfunctioning part.

HINT:
·

What was affected (system, part or meter warning indicators)

·

What happened (details of the malfunction)

·

When (occurrence date and time, frequency and if it recurs or not)

·

Under what kind of situation did the problem occur (driving and operating condition at the occurrence and weather)

·

Road type or condition (city, suburb, paved road, unpaved road, highway, etc.)

·

Return conditions (what made the vehicle return to normal. Example: ignition switch was turned off)

Points to be confirmed
Symptom
·

Electric power steering

-

Normal

-

A little heavier than usual

-

There was no assist


·

Air conditioning

-

Whether the air conditioning system operated

-

Whether the blower fan operated


·

Wireless door lock function and smart entry function

-

Whether the lock/unlock function operated

-

Whether the illumination was turned on when the key was brought into a smart detection area


·

Operation of other systems of concern


Meter warning lights
·

Illumination of warning lights and the order in which they illuminated

-

Check engine (MIL)

-

ABS

-

SLIP

-

Brake

-

EPS

-

SRS

-

Others


·

Meter display

-

Speedometer







Result:
Result
NEXT



NEXT

3.CHECK GTS OPERATION
3.CHECK GTS OPERATION
HINT:

Read the GTS operators manual before use.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>GENERAL INFORMATION


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check that the GTS and ECUs can communicate with the ignition switch ON.

HINT:
·

If communication is impossible, the GTS screen will indicate an error.

·

If communication between the GTS and ECUs is impossible, either the GTS or vehicle has a malfunction.

·

When communication between the GTS and the vehicle is impossible, but communication is possible when the GTS is connected to another vehicle, the vehicle has the malfunction. Inspect the ECU power source circuits (in this case perform steps 22 to 23 first). In addition, check that the BAT terminal of the DLC3 receives battery voltage (11 V or more).

·

If communication between the GTS and ECUs is still impossible even when the GTS is connected to another vehicle, the GTS has the malfunction. Perform the self tests described in the GTS operators manual. (The GTS may be malfunctioning or its battery may be discharged.)




Result:
Result Proceed to
OK (Communication between the GTS and the vehicle is possible.) A
OK (Communication between the GTS and the vehicle is impossible but communication is possible when connected to another vehicle.) B
NG (Communication is not possible between the GTS and the vehicle, nor between the GTS and another vehicle.) C



A

4.CHECK DTC (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

B

22.CHECK V BUS MAIN LINE

C

Refer to GTS operator's manual

4.CHECK DTC (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Central Gateway / Trouble Codes.

OK:

DTC B1003 is not output.



Result:
Proceed to
OK
NG



OK

5.CHECK DTC

NG

6.REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)
5.CHECK DTC
a.

Using the GTS, perform All Codes to read current and history DTCs and record them.

NOTICE:
·

CAN communication DTCs are output when there is an open or short in any of the communication lines. Any problems with the power source of a corresponding ECU or sensor, or problems in the ECU, the sensor itself also cause these DTCs to be output.

·

If a CAN communication line connector is disconnected with the ignition switch ON, the ECUs of the corresponding system and related systems store a DTC.



HINT:
·

If an open in a CAN main bus line, a short between the CAN bus lines (CANH and CANL) or a +B or ground short in a CAN bus occurs, DTCs of almost all ECUs and sensors on the CAN bus may be output (or a message indicating a communication error may be displayed on the GTS screen). In this case, check the resistance of the CAN bus (steps 10 to 15) first.

·

If an open occurs in just one of the lines of a CAN branch, DTCs which are not related to malfunctioning parts may be output (DTCs may be displayed randomly), or a message indicating a communication error may be displayed on the GTS.




b.

Read the freeze frame data using the GTS and record it.


Result:
Result
NEXT



NEXT

8.PERFORM COMMUNICATION MALFUNCTION CHECK (CONNECTION STATUS CHECK USING GTS)
6.REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)
a.

Replace the central gateway ECU (network gateway ECU)

Click herePower Source / Network>NETWORKING>NETWORK GATEWAY ECU>REMOVAL

HINT:

DTC B1003 is stored when a malfunction is detected in the non-volatile storage of the central gateway ECU (network gateway ECU). As DTC B1003 is not related to a communication malfunction, continue with troubleshooting to find the cause of the communication malfunction after replacing the central gateway ECU (network gateway ECU).



Result:
Proceed to
NEXT



NEXT

7.CHECK DTC
7.CHECK DTC
a.

Using the GTS, perform Health Check to read current and history DTCs and record them.

NOTICE:
·

CAN communication DTCs are output when there is an open or short in any of the communication lines. Any problems with the power source of a corresponding ECU or sensor, or problems in the ECU or sensor itself also cause these DTCs to be output.

·

If a CAN communication line connector is disconnected with the Ignition switch ON, the ECUs of the corresponding system and related systems store a DTC.



HINT:
·

If an open in a CAN main bus line, a short between the CAN bus lines (CANH and CANL) or a short to ground or +B in a CAN bus occurs, DTCs of almost all ECUs and sensors on the CAN bus may be output (or a message indicating a communication error may be displayed on the GTS screen). In this case, check the resistance of the CAN bus (steps 10 to 15) first.

·

If an open occurs in just one of the lines of a CAN branch, DTCs which are not related to malfunctioning parts may be output (DTCs may be displayed randomly), or a message indicating a communication error may be displayed on the GTS.




b.

Read the freeze frame data using the GTS and record it.


Result:
Proceed to
NEXT



NEXT

8.PERFORM COMMUNICATION MALFUNCTION CHECK (CONNECTION STATUS CHECK USING GTS)
8.PERFORM COMMUNICATION MALFUNCTION CHECK (CONNECTION STATUS CHECK USING GTS)
a.

Select "Communication Malfunction Check" from the screen on the GTS.


b.

Record all the DTCs stored for ECUs and sensors.


Result:
Result
NEXT



NEXT

9.PERFORM CAN BUS CHECK (CONNECTION STATUS CHECK USING GTS)
9.PERFORM CAN BUS CHECK (CONNECTION STATUS CHECK USING GTS)
a.

Based on the vehicle equipment and specifications, confirm the systems that use CAN communication.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(w/ Toyota Safety Sense)>DIAGNOSIS SYSTEM


b.

Select "CAN Bus Check" from the screen on the GTS.


c.

Observe the screen for approximately 2 minutes to check the ECUs and sensors displayed on the screen.


Result:
Result
NEXT



NEXT

10.CHECK BUS 2 MAIN LINE (CANH - CANL)
10.CHECK BUS 2 MAIN LINE (CANH - CANL)
NOTICE:

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.


HINT:

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.


a.
C355653C04
1.458,0.354 1.917,0.615 0.458,0.26 1.271,1.74 1.656,1.146 true 2.125,1.75 1.75,1.156 true 0.135,0.125 0.448,0.323 0.313,0.198 10 false *a 1.542,0.396 2.156,0.594 0.615,0.198 10 false F139 1.01,1.781 1.625,1.979 0.615,0.198 10 false CA4H 2.01,1.771 2.625,1.969 0.615,0.198 10 false CA4L
*a Component with harness connected (Central Gateway ECU (Network Gateway ECU))


Disconnect the cable from the negative (-) battery terminal.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F139-18 (CA4H) - F139-17 (CA4L) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result Proceed to
OK A
NG (70 Ω or higher) B
NG (Below 54 Ω) C



A

11.CHECK FOR SHORT TO GND IN BUS 2 (CANH, CANL - CG)

B

C

11.CHECK FOR SHORT TO GND IN BUS 2 (CANH, CANL - CG)
a.
C355654C10
1.49,0.292 1.906,0.563 0.417,0.271 1.5,2.531 1.917,2.802 0.417,0.271 1.219,1.781 1.656,1.115 true 2.25,1.74 1.771,1.115 true 1.167,2.771 1.583,3.167 true 0.135,0.052 0.448,0.25 0.313,0.198 10 false *a 1.552,0.354 1.948,0.552 0.396,0.198 10 false F139 0.958,1.792 1.354,1.99 0.396,0.198 10 false CA4H 2.115,1.781 2.51,1.979 0.396,0.198 10 false CA4L 1.625,2.583 2.021,2.781 0.396,0.198 10 false F4 0.906,2.677 1.302,2.875 0.396,0.198 10 false CG 0.177,2.51 0.49,2.708 0.313,0.198 10 false *1
*1 DLC3
*a Component with harness connected (Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F139-18 (CA4H) - F4-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
F139-17 (CA4L) - F4-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

12.CHECK FOR SHORT TO +B IN BUS 2 (CANH, CANL - BAT)

NG

12.CHECK FOR SHORT TO +B IN BUS 2 (CANH, CANL - BAT)
a.
C355654C11
1.51,0.302 1.938,0.563 0.427,0.26 1.479,2.563 1.906,2.823 0.427,0.26 1.26,1.74 1.656,1.135 true 2.177,1.729 1.76,1.125 true 2.573,4.177 2.354,3.75 true 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a 1.563,0.344 1.948,0.552 0.385,0.208 10 false F139 1.073,1.76 1.458,1.969 0.385,0.208 10 false CA4H 2.073,1.76 2.458,1.969 0.385,0.208 10 false CA4L 1.604,2.604 1.99,2.813 0.385,0.208 10 false F4 2.573,4.198 2.958,4.406 0.385,0.208 10 false BAT 0.125,2.469 0.438,2.667 0.313,0.198 10 false *1
*1 DLC3
*a Component with harness connected (Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F139-18 (CA4H) - F4-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F139-17 (CA4L) - F4-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.CHECK BUS 3 MAIN LINE (CANH - CANL)

NG

13.CHECK BUS 3 MAIN LINE (CANH - CANL)
NOTICE:

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.


HINT:

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.


a.
C364705C01
1.469,0.115 1.969,0.365 0.5,0.25 1.385,0.979 1,0.448 true 1,1.667 1.417,1.125 true 1.563,0.156 2.177,0.354 0.615,0.198 10 false F139 0.573,0.344 1.188,0.542 0.615,0.198 10 false CA3H 0.802,1.708 1.417,1.906 0.615,0.198 10 false CA3L 0.115,0.063 0.365,0.313 0.25,0.25 10 false *a
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F139-6 (CA3H) - F139-21 (CA3L) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result Proceed to
OK A
NG (70 Ω or higher) B
NG (Below 54 Ω) C



A

14.CHECK FOR SHORT TO GND IN BUS 3 (CANH, CANL - CG)

B

C

14.CHECK FOR SHORT TO GND IN BUS 3 (CANH, CANL - CG)
a.
C364708C01
1.458,0.302 1.958,0.552 0.5,0.25 1.917,2.583 2.417,2.833 0.5,0.25 1,1.75 1.417,1.135 true 1,0.417 1.385,0.969 true 1.583,3.188 1.25,2.667 true 1.531,0.333 2.146,0.531 0.615,0.198 10 false F139 2.083,2.615 2.313,2.833 0.229,0.219 10 false F4 0.99,2.563 1.604,2.76 0.615,0.198 10 false CG 0.594,0.323 1.208,0.521 0.615,0.198 10 false CA3H 0.792,1.792 1.406,1.99 0.615,0.198 10 false CA3L 0.115,0.094 0.365,0.292 0.25,0.198 10 false *a 0.115,2.344 0.365,2.542 0.25,0.198 10 false *1
*1 DLC3
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F139-6 (CA3H) - F4-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
F139-21 (CA3L) - F4-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Result
OK
NG



OK

15.CHECK FOR SHORT TO +B IN BUS 3 (CANH, CANL - BAT)

NG

15.CHECK FOR SHORT TO +B IN BUS 3 (CANH, CANL - BAT)
a.
C364708C02
1.458,0.302 1.958,0.552 0.5,0.25 1.917,2.583 2.417,2.833 0.5,0.25 1,1.75 1.417,1.135 true 1,0.417 1.385,0.969 true 2.667,4.167 2.396,3.76 true 1.531,0.333 2.146,0.531 0.615,0.198 10 false F139 2.083,2.615 2.313,2.833 0.229,0.219 10 false F4 2.604,4.219 3.219,4.417 0.615,0.198 10 false BAT 0.594,0.323 1.208,0.521 0.615,0.198 10 false CA3H 0.792,1.792 1.406,1.99 0.615,0.198 10 false CA3L 0.115,0.094 0.365,0.292 0.25,0.198 10 false *a 0.115,2.344 0.365,2.542 0.25,0.198 10 false *1
*1 DLC3
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F139-6 (CA3H) - F4-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F139-21 (CA3L) - F4-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Result
OK
NG



OK

16.CHECK RESULT OF CAN BUS CHECK (CONNECTION STATUS CHECK USING GTS)

NG

16.CHECK RESULT OF CAN BUS CHECK (CONNECTION STATUS CHECK USING GTS)
a.

Inspect or repair the probable malfunctioning part based on the check result of step 9 (the step in which CAN bus check was performed).


Result of CAN Bus Check (Connection Status Check Using GTS):
Result Proceed to
All ECUs and sensors connected to the CAN communication system are displayed as normal on the screen.
(CAN bus circuit is currently normal.)
A
One of the ECUs and sensors connected to the bus 2 or bus 3, is displayed as communication stop on the screen.
(Open in ECU or sensor branch lines, or communication is interrupted.)
B
In addition to ECUs and sensors which are connected to the bus 2 but are displayed as communication stop on the screen, there are ECUs or sensors for which the detection status changes (changes between detected and not detected) during the inspection.
(Open in one side of ECU or sensor branch lines.)
C
In addition to ECUs and sensors which are connected to the bus 3 but are displayed as communication stop on the screen, there are ECUs or sensors for which the detection status changes (changes between detected and not detected) during the inspection.
(Open in one side of ECU or sensor branch lines.)
D


NOTICE:
·

Non-installed ECUs or sensors will not be displayed. Do not mistake them for being in communication stop mode.

·

It may be possible to select buses that do not have ECUs or sensors from the bus selection pull-down menu on the GTS. This is not a malfunction. (This occurs when optional devices are not on a sub bus that is monitored by a gateway function equipped ECU.)



HINT:
·

Regarding CAN Bus Check, refer to How to Interpret CAN Bus Check Screen.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(w/ Toyota Safety Sense)>DIAGNOSIS SYSTEM

·

If the detection status of ECUs changes during the inspection, one of the branch lines of a connected ECU or sensor may be open. (Signals from the ECU or sensor that has an open in one of its branch lines create electrical noise, affecting response to the GTS and whether or not the ECUs and sensors are displayed.)

·

Regarding the communication stop mode for ECUs connected to sub bus 1, refer to the inspection procedure for the DTCs that indicate a communication stop.




A

17.CHECK RESULT OF CHECK COMMUNICATION MALFUNCTION DTCs (SELECT THE MALFUNCTIONING BUS)

B

C

D

17.CHECK RESULT OF CHECK COMMUNICATION MALFUNCTION DTCs (SELECT THE MALFUNCTIONING BUS)
a.

Inspect or repair the probable malfunctioning part based on the check result of step 7 (the step in which checking for communication malfunction DTCs was performed).

HINT:
·

When checking for communication DTCs, refer to How to Interpret Communication DTCs (DTCs that start with U).

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(w/ Toyota Safety Sense)>DIAGNOSIS SYSTEM

·

If communication DTCs are stored, and all ECUs and sensors connected to the CAN communication system are displayed as normal on the Communication Bus Check (CAN bus check) screen of the GTS, a past malfunction that is currently not occurring is suspected.

·

When a CAN branch of the CAN communication system is malfunctioning, because the ECUs and sensors related to it detect the malfunction, the problem area can be determined using the combination of DTCs that are output.




Result:
Result
NEXT



NEXT

18.DTC COMBINATION TABLE (CANH - CANL)
18.DTC COMBINATION TABLE (CANH - CANL)
a.

Confirm the problem according to the combination of output DTCs regarding the CAN communication system.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(w/ Toyota Safety Sense)>DIAGNOSIS SYSTEM

Result:
Result Proceed to
Combination of DTCs is not in DTC Combination Table A
Combination of DTCs is in DTC Combination Table B


HINT:

CAN communication system history DTCs may indicate the problem if CAN communication system DTCs are output and all ECUs and sensors connected to the CAN communication system are displayed on "Communication Bus Check" of the GTS.




A

19.IDENTIFICATION OF PROBLEM (PAST MALFUNCTION IN MAIN BUS)

B

19.IDENTIFICATION OF PROBLEM (PAST MALFUNCTION IN MAIN BUS)
a.

Connect the cable to the negative (-) battery terminal.


b.

Clear the DTCs using the GTS.


c.

Perform the tests in Symptom Simulation to check the wire harnesses and connectors including those for main bus lines.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING


d.

Based on the results of the check, inspect the parts that output DTCs to determine the malfunctioning part.

HINT:

If DTCs are output, do not turn the ignition switch off.



Result:
Result
NEXT



NEXT

20.REPAIR OR REPLACEMENT
20.REPAIR OR REPLACEMENT
Result:
Result
NEXT



NEXT

21.CONFIRMATION TEST
21.CONFIRMATION TEST
Result:
Result
NEXT



NEXT

END

22.CHECK V BUS MAIN LINE
NOTICE:

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.


HINT:

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.


a.

Disconnect the cable from the negative (-) battery terminal.


b.
C366082C01
1.417,0.167 1.917,0.417 0.5,0.25 1.979,0.917 2.396,0.5 true 1.5,1.885 1.917,1.469 true 2.323,1.469 2.74,1.885 true 1.135,0.5 1.552,0.917 true 0.083,0.073 0.396,0.229 0.313,0.156 10 false *1 2.469,0.385 3.083,0.583 0.615,0.198 10 false CANH 1.063,1.781 1.677,1.979 0.615,0.198 10 false CANL 2.813,1.781 3.229,2.01 0.417,0.229 10 false BAT 0.854,0.385 1.469,0.583 0.615,0.198 10 false CG 1.583,0.198 2.198,0.396 0.615,0.198 10 false F4
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F4-6 (CANH) - F4-14 (CANL) Cable disconnected from negative (-) battery terminal 54 to 66 Ω
F4-6 (CANH) - F4-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
F4-14 (CANL) - F4-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
F4-6 (CANH) - F4-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F4-14 (CANL) - F4-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher



Result:
Proceed to
OK
NG



OK

23.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CENTRAL GATEWAY ECU - DLC3)

23.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
U161134C03
0.448,0.99 0.25,1.833 true 2.979,0.99 3.125,1.771 true 0.75,1.833 0.563,1.208 true 0.854,0.25 0.677,0.917 true 1.167,1.833 0.76,1.208 true 0.073,0.042 0.24,0.198 0.167,0.156 10 false *a 1.552,0.167 1.958,0.365 0.406,0.198 10 false F139 0.063,1.875 0.469,2.021 0.406,0.146 10 false BATT 2.979,1.813 3.344,1.958 0.365,0.146 10 false GND 0.667,1.865 1.073,2.01 0.406,0.146 10 false IG1 0.896,0.156 1.302,0.302 0.406,0.146 10 false ACC 1.094,1.875 1.5,2.021 0.406,0.146 10 false IG2
*a Front view of wire harness connector
(to Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F139-10 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F139-1 (BATT) - Body ground Always 11 to 14 V
F139-2 (ACC) - Body ground Ignition switch ACC 11 to 14 V
F139-11 (IG1) - Body ground Ignition switch ON 11 to 14 V
F139-12 (IG2) - Body ground Ignition switch ON 11 to 14 V



Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)