Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › from 2017.01
RM19S0E _59 Vehicle Exterior _051505 LIGHTING (EXT) _0248415 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Taillight Relay Circuit  


DESCRIPTION

The main body ECU controls the TAIL relay.

WIRING DIAGRAM

E367517E01
1.104,1.24 2.938,1.438 1.833,0.198 10 false from Battery 0.063,2.26 1.531,2.75 1.469,0.49 10 false to Headlight Assembly (Clearance Lights) 0.063,2.844 1.677,3.375 1.615,0.531 10 false to Rear Combination Light Assembly (Taillights) 0.063,3.448 1.635,4.396 1.573,0.948 10 false to Rear Light Assembly (Taillights)*1 and License Plate Lights 3.104,1.271 3.417,1.469 0.313,0.198 10 false 3F 3.115,1.052 3.271,1.25 0.156,0.198 10 false 1 4.396,1.969 5.01,2.167 0.615,0.198 10 false TAIL 4.146,2.479 5.677,2.677 1.531,0.198 10 false TAIL NO. 2 3.125,3.438 6.135,3.75 3.01,0.313 10 false Instrument Panel Junction Block Assembly 5.76,3.865 6.99,4.104 1.229,0.24 10 false Main Body ECU 5.542,1.24 5.854,1.438 0.313,0.198 10 false MB 5.563,1.042 5.875,1.24 0.313,0.198 10 false 14 3.083,2.313 3.396,2.51 0.313,0.198 10 false 3C 3.104,2.885 3.417,3.083 0.313,0.198 10 false 3D 3.125,2.115 3.281,2.313 0.156,0.198 10 false 2 3.104,2.708 3.396,2.99 0.292,0.281 10 false 10 0.406,4.417 3.615,4.615 3.208,0.198 10 false *1: for LED Headlight 5.865,1.24 6.479,1.438 0.615,0.198 10 false TRLY

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body / Main Body / Active Test.


e.

According to the display on the GTS, perform the Active Test.

Main Body
Tester Display Test Part Control Range Diagnostic Note
Taillight Relay Taillight relay OFF or ON -

OK:

TAIL relay operates. (Clearance lights, taillights and license plate lights illuminate.)




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BATTERY)
2.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BATTERY)
E367518C01
0.5,1.073 1,1.333 0.5,0.26 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 0.688,1.125 1,1.323 0.313,0.198 10 false 3F
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)


a.

Disconnect the 3F instrument panel junction block assembly connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3F-1 - Body ground Always 11 to 14 V




OK

3.REPLACE MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE MAIN BODY ECU
a.


NEXT

4.PERFORM ACTIVE TEST USING GTS
4.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body / Main Body / Active Test.


e.

According to the display on the GTS, perform the Active Test.

Main Body
Tester Display Test Part Control Range Diagnostic Note
Taillight Relay Taillight relay OFF or ON -

OK:

TAIL relay operates. (Clearance lights, taillights and license plate lights illuminate.)




OK

END (MAIN BODY ECU WAS DEFECTIVE)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY