Home › Vehicle Exterior › WIPER / WASHER › REAR WIPER MOTOR › from 2017.01
RM19S0E _59 Vehicle Exterior _051504 WIPER / WASHER _0248406 REAR WIPER MOTOR A

WIPER / WASHER  REAR WIPER MOTOR  INSTALLATION  


PROCEDURE

Hide 85143R 1.INSTALL REAR WIPER MOTOR GROMMET

a.
E358677C02
1.354,0.469 1.708,1.073 1.708,1.073 2.125,0.469 true 1.625,1.125 1.938,1.281 0.313,0.156 10 false *a
*a Lip


Apply MP grease to the entire surface of the rear wiper motor grommet lip.

HINT:

Make sure that the hole does not clog with grease and the grooves on the lip are filled with grease.



b.
E358654C02
1.771,0.781 2.177,0.448 true 2.229,0.333 2.542,0.531 0.313,0.198 10 false *a
*a Alignment Mark


Install the rear wiper motor grommet.

HINT:

Install the rear wiper motor grommet with its alignment mark facing up.



Hide 85110R 2.INSTALL REAR WIPER MOTOR ASSEMBLY

a.

Insert the shaft of the rear wiper motor assembly through the rear wiper motor grommet, and temporarily install the rear wiper motor assembly with the 3 bolts.


b.
E358652N02
1.292,0.667 1.417,0.813 0.125,0.146 10 true 1 2.813,1.604 2.938,1.75 0.125,0.146 10 true 2 0.531,1.49 0.656,1.635 0.125,0.146 10 true 3

Fully tighten the 3 bolts in the order shown in the illustration.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


c.

Connect the connector.


Hide 3.INSTALL REAR WIPER ARM AND BLADE ASSEMBLY

a.

Turn the ignition switch on.


b.

Operate the rear wiper motor assembly and stop at the automatic stop (park) position.


c.

Turn the ignition switch off.


d.
E358655C02
1.031,1.073 1.615,1.073 true 1.813,3.125 2.26,3.24 true 0.302,3.833 0.604,3.375 true 0.833,1 1.146,1.198 0.313,0.198 10 false *b 2.313,3.156 2.625,3.354 0.313,0.198 10 false *c 0.125,3.75 0.438,3.948 0.313,0.198 10 false *a
*a Wire Brush
*b Wiper Arm Serration
*c Wiper Pivot Serration


When reusing the rear wiper arm:

i.

Clean the wiper arm serrations to remove any burrs, dirt, etc.

NOTICE:

Do not grind down the wiper arm serrations.




e.

Temporarily install the rear wiper arm and blade assembly.


f.
E358656C02
1.167,2.5 1.427,2.698 false 0.531,2.24 0.688,2.438 0.156,0.198 10 false A 0.531,2.552 0.688,2.75 0.156,0.198 10 false A 1.5,2.635 1.833,2.875 0.333,0.24 10 false *a
*a Alignment Mark


Align the rear wiper arm and blade assembly as shown in the illustration and install it with the nut.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)

HINT:

Hold the rear wiper arm hinge by hand while tightening the nut.


Reference Measurement:
Area Measurement
A 20.0 mm (0.787 in.)



g.

Turn the ignition switch on.


h.

Operate the rear wiper motor assembly while spraying washer fluid on the glass. Make sure that the rear wipers function properly and the wipers do not come into contact with the vehicle body.


i.

Turn the ignition switch off.


j.

Raise the rear wiper arm 2 times and check that the tip of the rear wiper blade is within the range shown in the illustration.


Hide 85292A 4.INSTALL REAR WIPER ARM HEAD CAP

a.

Engage the 2 guides and 2 claws to install the rear wiper arm head cap.

NOTICE:

Push down on the rear wiper arm head cap until a click sound can be heard.



Hide 67751 5.INSTALL BACK DOOR TRIM BOARD