Wear protective gloves. Sharp areas on the parts may injure your hands.
The procedure described below is for the LHD side. Use the same procedure for both the LHD and RHD side, unless otherwise specified.
72211
1.INSTALL SEAT TRACK ADJUSTING HANDLE
Engage the 2 hooks to install the seat track adjusting handle to the separate type front seat cushion spring assembly.
71849
2.INSTALL SEAT ADJUSTER COVER CAP
Install the 2 seat adjuster cover caps.
71640S
3.INSTALL SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY
Install the separate type front seatback spring assembly with the 4 bolts.
71537H
4.INSTALL SEAT CUSHION EDGE PROTECTOR RH
Engage the 2 guides to install the seat cushion edge protector RH.
Install the screw.
71538B
5.INSTALL SEAT CUSHION EDGE PROTECTOR LH
Engage the 2 guides to install the seat cushion edge protector LH.
Install the screw.
71873
6.INSTALL FRONT SEAT CUSHION LOWER SHIELD RH
Engage the clip to install the screw.
Engage the hook to install the front seat cushion lower shield RH as shown in the illustration.
71874
7.INSTALL FRONT SEAT CUSHION LOWER SHIELD LH
Engage the 2 clips.
Engage the hook to install the front seat cushion lower shield LH as shown in the illustration.
71875G
8.INSTALL RECLINING ADJUSTER INSIDE COVER RH
Engage the guide to install the reclining adjuster inside cover RH.
71876G
9.INSTALL RECLINING ADJUSTER INSIDE COVER LH
Engage the guide to install the reclining adjuster inside cover LH.
71873
10.INSTALL FRONT SEAT CUSHION LOWER SHIELD
Engage the 2 claws to install the front seat cushion lower shield.
71499B
11.INSTALL SEAT CUSHION SPRING DAMPER
Install the seat cushion spring damper with the 2 nuts.
73910A
12.INSTALL FRONT SEAT SIDE AIRBAG ASSEMBLY
Install the front seat side airbag assembly with 2 new nuts.
The nuts must not be reused.
Make sure that the separate type front seatback spring assembly is not deformed. If it is, replace it with a new one.
Engage the 2 clamps.
71074S
13.INSTALL SEPARATE TYPE FRONT SEATBACK COVER
For vehicles with side airbags, the side airbags may not be activated normally unless the separate type front seatback cover is securely installed.
Check that the strap is not twisted after installing the bracket.
Install the bracket securely.
Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 6 new hog rings.
| *1 | New Hog Ring |
| *2 | Hog Ring Pliers |
Be careful not to damage the cover.
When installing the hog rings, take care to minimize wrinkles as much as possible.
14.INSTALL SEATBACK COVER WITH PAD
Temporarily install the front seatback cover with pad.
Install the front seatback cover bracket with the 2 nuts.
For vehicles with side airbags, the side airbags may not be activated normally unless the front seatback cover is securely installed.
Check that the strap is not twisted after installing the bracket.
Install the bracket securely.
for Sport Package:
Fasten the 2 zippers.
Align the protruding portion of the front seat headrest support with the installation groove of the front seatback spring assembly.
| *a | Protruding |
Engage the 4 claws to install the 2 front seat headrest supports.
| *1 | Hog Ring |
| *a | Hog Ring Pliers |
Using hog ring pliers, install 2 new hog rings.
Do not soil or scratch the front seatback cover.
Using hog ring pliers, install 3 new hog rings.
| *1 | New Hog Ring |
| *2 | Hog Ring Pliers |
Do not soil or scratch the front seatback cover.
71072S
15.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER
Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 14 new hog rings.
| *1 | New Hog Ring |
| *2 | Hog Ring Pliers |
Be careful not to damage the separate type front seat cushion pad.
When installing the hog rings, take care to minimize wrinkles as much as possible.
Using hog ring pliers, install the 2 new hog rings.
| *1 | New Hog Ring |
| *2 | Hog Ring Pliers |
Be careful not to damage the cover.
When installing the hog rings, take care to minimize wrinkles as much as possible.
16.INSTALL SEAT CUSHION COVER WITH PAD
Engage the 5 hooks to temporarily install the seat cushion cover with pad.
Engage the 2 hooks.
Engage the 7 clamps to install the front seat side airbag wire harness.
Engage the 4 hooks to install the seat cushion cover with pad.
Fasten the hook and loop fastener.
Connect the seatback cover band.
71862
17.INSTALL FRONT SEAT CUSHION INNER SHIELD
Engage the 2 claws to install the front seat cushion inner shield.
71812D
18.INSTALL FRONT SEAT CUSHION SHIELD
Engage the clip and 2 claws to install the front seat cushion shield.
Install the screw.
72494
19.INSTALL VERTICAL ADJUSTING HANDLE
Install the vertical adjusting handle with the screw.
72526A
20.INSTALL RECLINING ADJUSTER RELEASE HANDLE
Engage the claw to install the reclining adjuster release handle.
71910A
21.INSTALL FRONT SEAT HEADREST ASSEMBLY
Install the front seat headrest assembly.
73240
22.INSTALL FRONT SEAT INNER BELT ASSEMBLY