CHECK COMBINATION METER ASSEMBLY
Disconnect the F1 combination meter assembly connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F1-40 (B) - Body ground | L - Body ground | Combination meter +B line | Always | 11 to 14 V |
| F1-39 (IG+) - Body ground | P - Body ground | Combination meter IG line | Ignition switch ON | 11 to 14 V |
| F1-21 (ET) - Body ground | BR - Body ground | Ground | Always | Below 1 Ω |
If the result is not as specified, there may be a malfunction on the wire harness side.
Reconnect the F1 combination meter assembly connector.
Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F1-7 (P/SB) - Body ground | P - Body ground | Front passenger seat belt signal | Front passenger seat occupied, seat belt fastened | Below 1 V |
| Front passenger seat occupied, seat belt unfastened | 11 to 14 V | |||
| F1-24 (RLSB) - Body ground | V - Body ground | Rear seat belt LH signal | Rear seat belt LH fastened | Below 1 V |
| Rear seat belt LH unfastened | 11 to 14 V | |||
| F1-25 (RCSB) - Body ground | R - Body ground | Rear seat center belt signal | Rear seat center belt fastened | Below 1 V |
| Rear seat center belt unfastened | 11 to 14 V | |||
| F1-26 (RRSB) - Body ground | BE - Body ground | Rear seat belt RH signal | Rear seat belt RH fastened | Below 1 V |
| Rear seat belt RH unfastened | 11 to 14 V | |||
| F1-1 (RLMT) - Body ground | GR - Body ground | Rear seat belt LH warning signal | Rear seat belt LH fastened | Below 1 V |
| Rear seat belt LH unfastened | 11 to 14 V | |||
| F1-2 (RCMT) - Body ground | G - Body ground | Rear seat center belt warning signal | Rear seat center belt fastened | Below 1 V |
| Rear seat center belt unfastened | 11 to 14 V | |||
| F1-3 (RRMT) - Body ground | B - Body ground | Rear seat belt RH warning signal | Rear seat belt RH fastened | Below 1 V |
| Rear seat belt RH unfastened | 11 to 14 V |
If the result is not as specified, the meter may have a malfunction.
CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
| *A | Main Body ECU 1 Connector Type | - | - |
| *1 | Instrument Panel Junction Block Assembly | *2 | Main Body ECU (Multiplex Network Body ECU) |
| *A | Main Body ECU 2 Connector Type | - | - |
| *1 | Instrument Panel Junction Block Assembly | *4 | Main Body ECU (Multiplex Network Body ECU) |
Remove the main body ECU from the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| MB-2 (FLCY) - Body ground | - | Front door courtesy light switch LH signal | Front door LH open | Below 1 Ω |
| Front door LH closed | 10 kΩ or higher | |||
| MB-11 (GND1) - Body ground | - | Ground | Always | Below 1 Ω |
| MB-29 (ACC) - Body ground | - | Ignition power supply | Ignition switch ACC | 11 to 14 V |
| MB-30 (BECU) - Body ground | - | Battery (ECU power source) | Always | 11 to 14 V |
| MB-32 (IG) - Body ground | - | Ignition power supply | Ignition switch ON | 11 to 14 V |
| F76-6 (RCTY) - Body ground | G - Body ground | Rear door courtesy light switch signal | Rear door open | Below 1 Ω |
| Rear door closed | 10 kΩ or higher | |||
| F76-24 (LCTY) - Body ground | L - Body ground | Rear door courtesy light switch signal | Rear door open | Below 1 Ω |
| Rear door closed | 10 kΩ or higher | |||
| F76-19 (FRCY) - Body ground | Y - Body ground | Front door courtesy light switch RH signal | Front door RH open | Below 1 Ω |
| Front door RH closed | 10 kΩ or higher |
If the result is not as specified, there may be a malfunction on the wire harness side.
Install the main body ECU to the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION).
Measure the voltage and check for pulse according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| 3D-34 (DBKL) - Body ground | W - Body ground | Driver seat belt warning signal | Driver seat belt fastened | 11 to 14 V |
| Driver seat belt unfastened | Below 1 V | |||
| F76-13 (CANL) - Body ground | W - Body ground | CAN communication line | Ignition switch ON | Pulse generation |
| F76-14 (CANH) - Body ground | R - Body ground | CAN communication line | Ignition switch ON | Pulse generation |
If the result is not as specified, the main body ECU may have a malfunction.