Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM › from 2017.10
RM19S0E _58 Vehicle Interior _051497 SEAT BELT _0248348 SEAT BELT WARNING SYSTEM J

SEAT BELT  SEAT BELT WARNING SYSTEM  Rear Seat Belt Warning Light Malfunction  


DESCRIPTION

When a rear door is opened and closed (the rear door courtesy light switch turns on and off) with the ignition switch ON, or when the ignition switch is turned from off to ON, the rear seat belt warning light in the telltale light assembly turns on to inform the driver of the rear seat belt condition. If a rear seat belt is fastened or unfastened, the warning light changes to indicate the current rear seat belt condition.

WIRING DIAGRAM

E376638E02
1.188,0.917 1.5,1.115 0.313,0.198 10 false K3 1.25,2.333 1.563,2.531 0.313,0.198 10 false K4 1.167,1.083 2.74,1.458 1.573,0.375 10 false Rear Door Courtesy Light Switch Assembly LH 1.25,2.5 2.813,2.927 1.563,0.427 10 false Rear Door Courtesy Light Switch Assembly RH 4.5,2.688 6.167,3.083 1.667,0.396 10 false Main Body ECU (Multiplex Network Body ECU) 4.5,2.469 4.958,2.667 0.458,0.198 10 false F76 4.833,0.75 5.448,0.948 0.615,0.198 10 false LCTY 4.833,2.083 5.448,2.281 0.615,0.198 10 false RCTY 4.583,0.635 4.896,0.833 0.313,0.198 10 false 24 4.594,1.938 4.75,2.104 0.156,0.167 10 false 6 0.75,3.167 4.417,3.365 3.667,0.198 10 false : CAN Communication Line 2.469,0.667 2.625,0.865 0.156,0.198 10 false 1 2.479,1.969 2.635,2.167 0.156,0.198 10 false 1

B446183E05
0.26,1.74 1.198,2.104 0.938,0.365 10 false from IG1 NO. 1 Relay 1.688,2 2.271,2.177 0.583,0.177 10 false GAUGE 2.802,1.854 3.25,2.021 0.448,0.167 10 false LAPB 2.813,2.313 3.26,2.479 0.448,0.167 10 false E 2.615,1.76 2.781,1.938 0.167,0.177 10 false 4 2.625,2.219 2.792,2.396 0.167,0.177 10 false 8 2.76,2.625 3.208,2.792 0.448,0.167 10 false F141 2.76,2.76 4.24,2.969 1.479,0.208 10 false Telltale Light Assembly 4.208,1.719 4.677,1.885 0.469,0.167 10 false RLID 4.208,2.063 4.646,2.24 0.438,0.177 10 false RCID 4.188,2.417 4.635,2.615 0.448,0.198 10 false RRID 4.615,1.615 4.938,1.781 0.323,0.167 10 false 5 4.635,1.958 4.958,2.125 0.323,0.167 10 false 6 4.615,2.344 4.938,2.51 0.323,0.167 10 false 7 5.271,1.604 5.448,1.76 0.177,0.156 10 false 1 5.281,1.958 5.604,2.125 0.323,0.167 10 false 2 5.281,2.344 5.604,2.51 0.323,0.167 10 false 3 5.448,1.698 5.896,1.865 0.448,0.167 10 false RLMT 5.458,2.042 5.906,2.208 0.448,0.167 10 false RCMT 5.458,2.417 5.906,2.583 0.448,0.167 10 false RRMT 5.458,3.083 5.906,3.25 0.448,0.167 10 false RLSB 5.469,5.427 5.917,5.594 0.448,0.167 10 false RRSB 5.458,3.969 5.906,4.135 0.448,0.167 10 false RCSB 5.198,2.979 5.521,3.146 0.323,0.167 10 false 24 5.208,5.302 5.531,5.469 0.323,0.167 10 false 26 5.208,3.865 5.531,4.031 0.323,0.167 10 false 25 2.563,2.979 2.729,3.156 0.167,0.177 10 false 2 2.573,3.865 2.74,4.042 0.167,0.177 10 false 4 0.479,2.99 0.646,3.167 0.167,0.177 10 false 3 0.479,3.875 0.646,4.052 0.167,0.177 10 false 5 0.927,3.229 2.406,3.438 1.479,0.208 10 false Rear Seat Inner Belt LH 0.979,4.135 2.458,4.344 1.479,0.208 10 false Rear Seat Center Belt 0.281,4.833 3.188,5.052 2.906,0.219 10 false Rear Seat Inner with Center Belt Assembly LH 0.281,4.688 0.573,4.854 0.292,0.167 10 false K51 3.49,5.313 3.656,5.49 0.167,0.177 10 false 2 4.615,5.313 4.781,5.49 0.167,0.177 10 false 1 2.885,5.74 3.177,5.906 0.292,0.167 10 false K52 2.875,5.885 5.052,6.104 2.177,0.219 10 false Rear Seat Inner Belt Assembly RH 5.271,5.885 5.563,6.052 0.292,0.167 10 false F1 5.271,6.021 7.115,6.229 1.844,0.208 10 false Combination Meter Assembly 0.51,6.438 2.354,6.646 1.844,0.208 10 false : CAN Communication Line 2.094,2.948 2.708,3.146 0.615,0.198 10 false LBR+ 0.656,2.948 1.271,3.146 0.615,0.198 10 false LBR- 2.104,3.854 2.719,4.052 0.615,0.198 10 false CBR+ 0.667,3.833 1.281,4.031 0.615,0.198 10 false CBR- 4.188,5.302 4.802,5.5 0.615,0.198 10 false RBR+ 3.646,5.302 4.26,5.5 0.615,0.198 10 false RBR-

CAUTION / NOTICE / HINT

NOTICE:
·

Since the seat belt warning system has functions that use CAN communication, first confirm that there is no malfunction in the communication system by inspecting the CAN communication functions in accordance with How to Proceed with Troubleshooting. Then conduct the following troubleshooting procedure.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.READ VALUE USING GTS (REAR DOOR COURTESY LIGHT SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

According to the display on the GTS, read the Data List.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
RR Door Courtesy SW Rear door courtesy light switch LH and RH signal / ON or OFF ON: Rear door LH or RH opened
OFF: Rear door LH and RH closed
-
RL Door Courtesy SW Rear door courtesy light switch LH and RH signal / ON or OFF ON: Rear door LH or RH opened
OFF: Rear door LH and RH closed
-

OK:

Normal conditions listed above are displayed.




OK

2.READ VALUE USING GTS (REAR SEAT BELT BUCKLE SWITCH)

NG

2.READ VALUE USING GTS (REAR SEAT BELT BUCKLE SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body / Combination Meter / Data List.


e.

According to the display on the GTS, read the Data List.

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
2nd-Row Seatbelt Buckle (R) Rear seat belt buckle RH signal / ON or OFF ON: Rear seat belt RH fastened
OFF: Rear seat belt RH unfastened
-
2nd-Row Seatbelt Buckle (L) Rear seat belt buckle LH signal / ON or OFF ON: Rear seat belt LH fastened
OFF: Rear seat belt LH unfastened
-
2nd-Row Seatbelt Buckle (C) Rear seat center belt buckle signal / ON or OFF ON: Rear seat center belt fastened
OFF: Rear seat center belt unfastened
-

OK:

Normal conditions listed above are displayed.


Result:
Result Proceed to
OK A
NG (LH or center side) B
NG (RH side) C




A

3.INSPECT TELLTALE LIGHT ASSEMBLY

B

6.INSPECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH

C

8.INSPECT REAR SEAT INNER BELT ASSEMBLY RH
3.INSPECT TELLTALE LIGHT ASSEMBLY
a.

Remove the telltale light assembly (See page Vehicle Exterior>LIGHTING (EXT)>HAZARD WARNING SWITCH>REMOVAL).


b.

Check that the rear passenger seat belt left indicator illuminates.

i.
E376667C01
1.458,1.74 1.896,1.958 0.438,0.219 1.938,2.531 2.354,2.302 true 1.01,3.042 1.427,2.813 true 0.26,1.76 0.573,1.958 0.313,0.198 10 false *a 2.406,2.177 3.021,2.417 0.615,0.24 10 false LAPB 0.688,3.021 1.302,3.26 0.615,0.24 10 false RLID 1.521,1.76 2.135,2 0.615,0.24 10 false F141
*a Component without harness connected
(Telltale Light Assembly)


Apply battery voltage to the telltale light assembly and check that the rear passenger seat belt left indicator illuminates.

OK:
Measurement Condition Specified Condition
Battery positive (+) → F141-4 (LAPB)
Battery negative (-) → F141-5 (RLID)
illuminates


HINT:

If the result is not as specified, replace the telltale light assembly.




c.

Check that the rear passenger seat belt center indicator illuminates.

i.
E376666C01
1.479,1.74 1.875,1.948 0.396,0.208 1.958,2.521 2.385,2.302 true 1.104,3.073 1.594,2.823 true 0.281,1.729 0.594,1.927 0.313,0.198 10 false *a 0.75,3.052 1.271,3.24 0.521,0.188 10 false RCID 2.427,2.146 2.948,2.333 0.521,0.188 10 false LAPB 1.531,1.75 2.052,1.938 0.521,0.188 10 false F141
*a Component without harness connected
(Telltale Light Assembly)


Apply battery voltage to the telltale light assembly and check that the rear passenger seat belt left indicator illuminates.

OK:
Measurement Condition Specified Condition
Battery positive (+) → F141-4 (LAPB)
Battery negative (-) → F141-6 (RCID)
illuminates


HINT:

If the result is not as specified, replace the telltale light assembly.




d.

Check that the rear passenger seat belt left indicator illuminates.

i.
E376668C01
1.479,1.75 1.875,1.958 0.396,0.208 1.958,2.531 2.354,2.354 true 1.771,2.813 2.25,3.094 true 0.281,1.771 0.594,1.927 0.313,0.156 10 false *a 2.406,2.229 3.01,2.49 0.604,0.26 10 false LAPB 2.271,3.083 2.875,3.344 0.604,0.26 10 false RRID 1.531,1.771 2.135,2.031 0.604,0.26 10 false F141
*a Component without harness connected
(Telltale Light Assembly)


Apply battery voltage to the telltale light assembly and check that the rear passenger seat belt left indicator illuminates.

OK:
Measurement Condition Specified Condition
Battery positive (+) → F141-4 (LAPB)
Battery negative (-) → F141-5 (RRID)
illuminates


HINT:

If the result is not as specified, replace the telltale light assembly.





OK

4.CHECK HARNESS AND CONNECTOR (TELLTALE LIGHT ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

REPLACE TELLTALE LIGHT ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (TELLTALE LIGHT ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the F141 telltale light assembly connector.


b.

Disconnect the F1 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F1-1 (RLMT) - F141-5 (RLID) Always Below 1 Ω
F1-2 (RCMT) - F141-6 (RCID) Always Below 1 Ω
F1-3 (RRMT) - F141-7 (RRID) Always Below 1 Ω
F141-8 (E) - Body ground Always Below 1 Ω
F1-1 (RLMT) or F141-5 (RLID) - Body ground Always 10 kΩ or higher
F1-2 (RCMT) or F141-6 (RCID) - Body ground Always 10 kΩ or higher
F1-3 (RRMT) or F141-7 (RRID) - Body ground Always 10 kΩ or higher




OK

5.CHECK TELLTALE LIGHT ASSEMBLY (REAR SEAT BELT WARNING LIGHT SOURCE VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK TELLTALE LIGHT ASSEMBLY (REAR SEAT BELT WARNING LIGHT SOURCE VOLTAGE)
E376643C04
1.51,0.313 1.927,0.552 0.417,0.24 1.979,1.271 2.281,1.719 true 2.333,1.667 2.74,1.844 0.406,0.177 10 false LAPB 1.552,0.354 1.896,0.51 0.344,0.156 10 false F141 0.208,0.167 0.521,0.365 0.313,0.198 10 false *a
*a Front view of wire harness connector (to Telltale Light Assembly)


a.

Connect the combination meter assembly connector to the combination meter assembly.


b.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F141-4 (LAPB) - Body ground Ignition switch ON 11 to 14 V




OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH
a.

Remove the rear seat inner with center belt assembly LH (See page Vehicle Interior>SEAT BELT>REAR SEAT INNER BELT ASSEMBLY(for LH Side)>REMOVAL).


b.

Inspect the rear seat inner with center belt assembly LH (See page Vehicle Interior>SEAT BELT>REAR SEAT INNER BELT ASSEMBLY(for LH Side)>INSPECTION).



OK

7.CHECK HARNESS AND CONNECTOR (REAR SEAT INNER WITH CENTER BELT LH - COMBINATION METER ASSEMBLY AND BODY GROUND)

NG

REPLACE REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH

7.CHECK HARNESS AND CONNECTOR (REAR SEAT INNER WITH CENTER BELT LH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the K51 rear seat inner with center belt assembly LH connector.


b.

Disconnect the F1 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K51-2(LBR+) - F1-24 (RLSB) Always Below 1 Ω
K51-3(LBR-) - Body ground Always Below 1 Ω
K51-2(LBR+) or F1-24 (RLSB) - Body ground Always 10 kΩ or higher
K51-4(CBR+) - F1-25 (RCSB) Always Below 1 Ω
K51-5(CBR-) - Body ground Always Below 1 Ω
K51-4(CBR+) or F1-25 (RCSB) - Body ground Always 10 kΩ or higher




OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT REAR SEAT INNER BELT ASSEMBLY RH
a.

Remove the rear seat inner belt assembly RH (See page Vehicle Interior>SEAT BELT>REAR SEAT INNER BELT ASSEMBLY(for RH Side)>REMOVAL).


b.

Inspect the rear seat inner belt assembly RH (See page Vehicle Interior>SEAT BELT>REAR SEAT INNER BELT ASSEMBLY(for RH Side)>INSPECTION).



OK

9.CHECK HARNESS AND CONNECTOR (REAR SEAT INNER BELT ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND)

NG

9.CHECK HARNESS AND CONNECTOR (REAR SEAT INNER BELT ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the K52 rear seat inner belt assembly RH connector.


b.

Disconnect the F1 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K52-1(RBR+) - F1-26 (RRSB) Always Below 1 Ω
K52-2(RBR-) - Body ground Always Below 1 Ω
K52-1(RBR+) or F1-26 (RRSB) - Body ground Always 10 kΩ or higher




OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR