Home › Engine / Hybrid System › 1NZ-FE ENGINE CONTROL › SFI SYSTEM (for Sedan)

DTC    P0115    Engine Coolant Temperature Circuit Malfunction

DTC    P0117    Engine Coolant Temperature Circuit Low Input

DTC    P0118    Engine Coolant Temperature Circuit High Input


DESCRIPTION

A thermistor is built into the Engine Coolant Temperature (ECT) sensor, of which the resistance value varies according to the ECT.
The structure of the sensor and its connection to the ECM are the same as those of the Intake Air Temperature (IAT) sensor.

HINT:
When any of DTCs P0115, P0117 and P0118 are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECT is estimated to be 80°C (176°F) by the ECM. Fail-safe mode continues until a pass condition is detected.


DTC No.
DTC Detection Condition
Trouble Area
P0115
Open or short in ECT sensor circuit for 0.5 seconds (1 trip detection logic)
  1. Open or short in ECT sensor circuit
  2. ECT sensor
  3. ECM
P0117
Short in ECT sensor circuit for 0.5 seconds (1 trip detection logic)
  1. Short in ECT sensor circuit
  2. ECT sensor
  3. ECM
P0118
Open in ECT sensor circuit for 0.5 seconds (1 trip detection logic)
  1. Open in ECT sensor circuit
  2. ECT sensor
  3. ECM

HINT:
When any of these DTCs are output, check the ECT by entering the following menus on the Techstream: Powertrain / Engine and ECT / Data List / Coolant Temp.


Temperature Displayed
Malfunction
-40°C (-40°F)
Open circuit
140°C (284°F) or higher
Short circuit

WIRING DIAGRAM


A112566E03


INSPECTION PROCEDURE

HINT:
  1. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  2. If DTC P0117 is stored, check that the engine does not overheat (the DTC P0117 may be stored due to engine overheating).

1.READ VALUE USING TECHSTREAM (ENGINE COOLANT TEMPERATURE)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Read the value displayed on the Techstream.

    Standard Value:
    80°C to 100°C (167°F to 212°F) with warm engine.


    Result 
    Temperature Displayed
    Proceed To
    -40°C (-40°F)
    A
    140°C (284°F) or higher
    B
    80°C to 100°C (167°F to 212°F)
    C

    HINT:
    1. If there is an open circuit, the Techstream indicates -40°C (-40°F).
    2. If there is a short circuit, the Techstream indicates 140°C (284°F) or higher.



B
Go to step 4

C
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


2.READ VALUE USING TECHSTREAM (CHECK FOR OPEN IN WIRE HARNESS)
A107691E07
  1. Disconnect the C19 Engine Coolant Temperature (ECT) sensor connector.

  1. Connect terminals 1 and 2 of the ECT sensor connector on the wire harness side.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Read the value displayed on the Techstream.

    Standard Value:
    140°C (284°F) or higher.

  1. Reconnect the ECT sensor connector.



NG
Go to step 3
OK

CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)  

3.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
A112602E01
  1. Disconnect the C19 ECT sensor connector.

  1. Disconnect the C20 ECM connector.

  1. Check the resistance.

    Standard resistance:
    Tester Connections
    Specified Conditions
    THW (C19-2) - THW (C20-97)
    Below 1 Ω
    E2 (C19-1) - ETHW (C20-96)

  1. Reconnect the ECT sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

GOOD CONNECTION TO ECM. IF OK, REPLACE ECM (Click here)  

4.READ VALUE USING TECHSTREAM (CHECK FOR SHORT IN WIRE HARNESS)
A084869E26
  1. Disconnect the C19 ECT sensor connector.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Read the value displayed on the Techstream.

    Standard Value:
    -40°C (-40°F)

  1. Reconnect the ECT sensor connector.



NG
Go to step 5
OK

REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)  

5.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
A112602E02
  1. Disconnect the C19 ECT sensor connector.

  1. Disconnect the C20 ECM connector.

  1. Check the resistance.

    Standard resistance:
    Tester Connections
    Specified Conditions
    THW (C19-2) or THW (C20-97) - Body ground
    10 kΩ or higher

  1. Reconnect the ECT sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)