Home › Engine / Hybrid System › 1NZ-FE ENGINE CONTROL › SFI SYSTEM (for Sedan)

DTC    P0120    Throttle / Pedal Position Sensor / Switch "A" Circuit Malfunction

DTC    P0121    Throttle / Pedal Position Sensor / Switch "A" Circuit Range / Performance Problem

DTC    P0122    Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input

DTC    P0123    Throttle / Pedal Position Sensor / Switch "A" Circuit High Input

DTC    P0220    Throttle / Pedal Position Sensor / Switch "B" Circuit

DTC    P0222    Throttle / Pedal Position Sensor / Switch "B" Circuit Low Input

DTC    P0223    Throttle / Pedal Position Sensor / Switch "B" Circuit High Input

DTC    P2135    Throttle / Pedal Position Sensor / Switch "A" / "B" Voltage Correlation


DESCRIPTION

HINT:
These DTCs relate to the Throttle Position (TP) sensor.

The TP sensor is mounted on the throttle with motor body assembly, and detects the opening angle of the throttle valve. This sensor is a non-contact type, and uses Hall-effect elements, in order to yield accurate signals, even in extreme driving conditions, such as at high speeds as well as very low speeds.
The TP sensor has two sensor circuits which each transmits a signal, VTA1 and VTA2. VTA1 is used to detect the throttle valve angle and VTA2 is used to detect malfunctions in VTA1. The sensor signal voltages vary between 0 V and 5 V in proportion to the throttle valve opening angle, and are transmitted to the VTA terminals of the ECM.
As the valve closes, the sensor output voltage decreases and as the valve opens, the sensor output voltage increases. The ECM calculates the throttle valve opening angle according to these signals and controls the throttle actuator in response to driver inputs. These signals are also used in calculations such as air-fuel ratio correction, power increase correction and fuel cut control.

A208679E42


DTC No.
DTC Detection Condition
Trouble Area
P0120
Output voltage of VTA1 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds or more when accelerator pedal depressed
(1 trip detection logic)
  1. Throttle with motor body assembly
  2. ECM
P0121
Difference between VTA1 and VTA2 voltages less than 0.8 V, or more than 1.6 V for 2 seconds (1 trip detection logic)
  1. Throttle with motor body assembly
  2. TP sensor circuit
  3. ECM
P0122
Output voltage of VTA1 0.2 V or less for 2 seconds or more when accelerator pedal depressed
(1 trip detection logic)
  1. Throttle with motor body assembly
  2. Short in VTA1 circuit
  3. Open in VC circuit
  4. ECM
P0123
Output voltage of VTA1 4.535 V or more for 2 seconds or more when accelerator pedal depressed
(1 trip detection logic)
  1. Throttle with motor body assembly
  2. Open in VTA1 circuit
  3. Open in E2 circuit
  4. Short between VC and VTA1 circuits
  5. ECM
P0220
Output voltage of VTA2 quickly fluctuates beyond lower and upper malfunction thresholds for 2 seconds or more when accelerator pedal depressed
(1 trip detection logic)
  1. Throttle with motor body assembly
  2. ECM
P0222
Output voltage of VTA2 1.75 V or less for 2 seconds or more when accelerator pedal depressed
(1 trip detection logic)
  1. Throttle with motor body assembly
  2. Short in VTA2 circuit
  3. Open in VC circuit
  4. ECM
P0223
Output voltage of VTA2 4.8 V or more, and VTA1 between 0.2 V and 2.02 V for 2 seconds or more when accelerator pedal depressed
(1 trip detection logic)
  1. Throttle with motor body assembly
  2. Open in VTA2 circuit
  3. Open in E2 circuit
  4. Short between VC and VTA2 circuits
  5. ECM
P2135
Either condition (a) or (b) met (1 trip detection logic):
(a) Difference between output voltages of VTA1 and VTA2 0.02 V or less for 0.5 seconds or more
(b) Output voltage of VTA1 0.2 V or less, and VTA2 1.75 V or less, for 0.4 seconds or more
  1. Short between VTA1 and VTA2 circuits
  2. Throttle with motor body assembly
  3. ECM

HINT:
  1. When any of these DTCs are output, check the throttle valve opening angle by entering the following menus on the Techstream: Powertrain / Engine and ECT / Data List / Throttle Position No.1 and Throttle Position No.2.
  1. Throttle Position No.1 denotes the VTA1 signal, and Throttle Position No.2 denotes the VTA2 signal.

    Reference (Normal Condition):

    Techstream Display
    Accelerator Pedal Fully Released
    Accelerator Pedal Fully Depressed
    Throttle Position No.1
    0.5 to 1.1 V
    3.2 to 4.8 V
    Throttle Position No.2
    2.1 to 3.1 V
    4.6 to 4.9 V


CONFIRMATION DRIVING PATTERN


A198824E01

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Start the engine.
  7. With the vehicle stationary, fully depress and release the accelerator pedal [B].
  8. Idle the engine for 2 seconds or more [C].
  9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].
  10. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  12. Input the DTC: P0120, P0121, P0122, P0123, P0220, P0222, P0223 or P2135.
  13. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the result shows INCOMPLETE or N/A, perform steps [B] through [D] again.


FAIL-SAFE

When any of these DTCs, or other DTCs relating to ETCS (Electronic Throttle Control System) malfunctions, are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts off the current to the throttle actuator, and the throttle valve is returned to a 6° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel cut) and ignition timing, in accordance with the accelerator pedal opening angle, to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.
Fail-safe mode continues until a pass condition is detected, and the ignition switch is then turned to OFF.

WIRING DIAGRAM


A256690E06


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.READ VALUE USING TECHSTREAM (THROTTLE POSITION NO.1 AND THROTTLE POSITION NO.2)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Throttle Position No.1 and Throttle Position No.2.

  1. Check the values displayed on the Techstream.

    Result 
    When Accelerator Pedal Released
    When Accelerator Pedal Depressed
    Trouble Areas
    Proceed to
    Throttle Position No.1
    Throttle Position No.2
    Throttle Position No.1
    Throttle Position No.2
    0 V to 0.2 V
    0 V to 0.2 V
    0 V to 0.2 V
    0 V to 0.2 V
    VC circuit open
    A
    4.5 V to 4.9 V
    4.5 V to 4.9 V
    4.5 V to 4.9 V
    4.5 V to 4.9 V
    E2 circuit open
    0 V to 0.2 V,
    or 4.5 V to 4.9 V
    2.1 V to 3.1 V
    (Fail-safe)
    0 V to 0.2 V,
    or 4.5 V to 4.9 V
    2.1 V to 3.1 V
    (Fail-safe)
    VTA1 circuit open or ground short
    0.6 V to 1.4 V
    (Fail-safe)
    0 V to 0.2 V,
    or 4.5 V to 4.9 V
    0.6 V to 1.4 V
    (Fail-safe)
    0 V to 0.2 V,
    or 4.5 V to 4.9 V
    VTA2 circuit open or ground short
    0.5 V to 1.1 V
    2.1 V to 3.1 V
    3.2 V to 4.8 V
    (Not fail-safe)
    4.6 V to 4.9 V
    (Not fail-safe)
    TP sensor circuit normal
    B

HINT:
  1. DTC P0121 is stored when the VTA1 and VTA2 output voltages are not consistent with the sensor characteristics. Therefore, check the freeze frame data when this DTC is stored. Use the following formula to confirm the relative differences in voltage.

    Characteristic Sensor Output:
    VTA2 x 0.8 is approximately equal to VTA1 + 1.11 V
    VTA1: Throttle Position No. 1.
    VTA2: Throttle Position No. 2.

  2. If DTC P0121 is output, proceed to the "Check Harness and Connector (Throttle with Motor Body Assembly- ECM)".



B
Go to step 5
A


2.CHECK HARNESS AND CONNECTOR (THROTTLE WITH MOTOR BODY ASSEMBLY - ECM)
A107944E76
  1. Disconnect the C17 throttle with motor body assembly connector.

  1. Disconnect the C20 ECM connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connections
    Specified Conditions
    VC (C17-5) - VCTA (C20-67)
    Below 1 Ω
    VTA (C17-6) - VTA1 (C20-115)
    VTA2 (C17-4) - VTA2 (C20-114)
    E2 (C17-3) - ETA (C20-91)

    Standard resistance (Check for short):
    Tester Connections
    Specified Conditions
    VC (C17-5) or VCTA (C20-67) - Body ground
    10 kΩ or higher
    VTA (C17-6) or VTA1 (C20-115) - Body ground
    VTA2 (C17-4) or VTA2 (C20-114) - Body ground

  1. Reconnect the throttle with motor body assembly connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT ECM (VC VOLTAGE)
A107895E99
  1. Disconnect the C17 throttle with motor body assembly connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage between the terminals of the throttle with motor body assembly connector.

    Standard voltage:
    Tester Connections
    Specified Conditions
    VC (C17-5) - E2 (C17-3)
    4.5 to 5.5 V

  1. Reconnect the throttle with motor body assembly connector.



NG
REPLACE ECM (Click here)
OK


4.REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY
  1. Replace the throttle with motor body assembly (Click here).


NEXT


5.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

  1. Read DTCs.

    Result 
    Display (DTC Output)
    Proceed To
    P0120, P0121, P0122, P0123, P0220, P0222, P0223, and/or P2135
    A
    No output
    B



B
END
A

REPLACE ECM (Click here)