DTC P0505 Idle Control System Malfunction |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0505 | Idling speed continues to vary greatly from the target idling speed (2 trip detection logic). |
|

| Related DTCs | P0505: Idle Speed Control Function |
| Required Sensors/Components (Main) | Electronic throttle control system |
| Required Sensors/Components (Related) | Crankshaft position sensor Engine coolant temperature sensor Vehicle speed sensor |
| Frequency of Operation | Once per driving cycle |
| Duration | 5 seconds |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | P0010 (Camshaft Timing Oil Control Valve) P0011 (VVT System - Advance) P0012 (VVT System - Retard) P0016 (VVT System - Misalignment) P0031, P0032, P101D (Air Fuel Ratio Sensor Heater) P0102, P0103 (Mass Air Flow Meter) P0115, P0117, P0118 (Engine Coolant Temperature Sensor) P0125 (Insufficient Coolant Temperature for Closed Loop Fuel Control) P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle Position Sensor) P0171, P0172 (Fuel System) P0301 - P0304 (Misfire) P0335 (Crankshaft Position Sensor) P0340 (Camshaft Position Sensor) P0351 - P0354 (Igniter) P0451, P0452, P0453 (EVAP System) P0500 (Vehicle Speed Sensor) P0705 (Shift Lever Position Switch) P0973, P0974, P0976, P0977 (Shift Solenoid Valve) P219A (Air Fuel Ratio Imbalance) P2195, P2196, P2237, P2238, P2239, P2252, P2253, P014C, P014D, P015A, P015B (Air Fuel Ratio Sensor) |
| Engine | Running |
| Either condition is met | 1 or 2 |
| 1. Both of following conditions A and B met | - |
| A. Engine speed - Target engine speed | Less than -100 rpm, or more than 150 rpm (A/C off and NSW off) Less than -100 rpm, or more than 200 rpm (A/C on or NSW on) |
| B. IAC flow rate learned value | 0.55 L/sec. or less, or 4.5 L/sec. or more for 5 seconds or more |
| 2. Both of following conditions C and D met | - |
| C. Frequency that both of following conditions (a) and (b) met | 5 times or more |
| (a) Engine speed - Target engine speed | Less than -100 rpm, or more than 150 rpm (A/C off and NSW off) Less than -100 rpm, or more than 200 rpm (A/C on or NSW on) |
| (b) Vehicle condition | Stopped after being driven at 10 km/h (6.25 mph) or more |
| D. Amount of change of IAC flow rate learned value | +2.01 L/sec. or more, or -2.53 L/sec. or less |

| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0505) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed to |
| DTC P0505 is output | A |
| DTC P0505 and other DTCs are output | B |
|
| ||||
| A | |
| 2.CHECK PCV HOSE CONNECTIONS |
Check the PCV hose connections (Click here).
|
| ||||
| OK | |
| 3.CHECK INTAKE SYSTEM |
Check the intake system for vacuum leaks (Click here).
|
| ||||
| OK | |
| 4.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY (THROTTLE VALVE) |
Check the throttle body with motor assembly condition.
|
| ||||
| OK | |
| 5.CONFIRM WHETHER DTC OUTPUT RECURS |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the Techstream on.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed to |
| DTC P0505 is output | A |
| No DTC is output | B |
|
| ||||
| A | ||
| ||