Home › Engine / Hybrid System › 1NZ-FE ENGINE CONTROL › SFI SYSTEM (for Sedan)

DTC    P0560    System Voltage


DESCRIPTION

The battery supplies electricity to the ECM even when the ignition switch is in the OFF position. This power allows the ECM to store data such as DTC history, freeze frame data and fuel trim values. If the battery voltage falls below a minimum level, these memories are cleared and the ECM determines that there is a malfunction in the power supply circuit. When the engine is next started, the ECM illuminates the MIL and stores the DTC.

DTC No.
DTC Detection Condition
Trouble Area
P0560
Open in ECM back up power source circuit
(1 trip detection logic)
  1. Open in back up power source circuit
  2. Battery
  3. Battery terminals
  4. EFI fuse
  5. ECM

HINT:
If DTC P0560 is stored, the ECM does not store other DTCs or the data stored in the ECM are partly erased.


WIRING DIAGRAM


A112571E01


INSPECTION PROCEDURE

NOTICE:
  1. After turning ignition switch off, waiting may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK FUSE (EFI FUSE)
A112606E01
  1. Remove the EFI fuse from the engine room relay block.

  1. Check the resistance of the EFI fuse.

    Standard resistance:
    Below 1 Ω

  1. Reinstall the EFI fuse.



NG
CHECK FOR SHORTS IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK


2.CHECK HARNESS AND CONNECTOR (ECM - EFI FUSE, EFI FUSE - BATTERY)
A107903E02
  1. Check the harness and the connector between the EFI fuse and ECM.

    1. Remove the EFI fuse from the engine room relay block.

    2. Disconnect the A21 ECM connector.

    3. Check the resistance.

      Standard resistance (Check for open):
      Tester Connections
      Specified Conditions
      EFI fuse (2) - BATT (A21-20)
      Below 1 Ω

      Standard resistance (Check for short):
      Tester Connections
      Specified Conditions
      EFI fuse (2) or BATT (A21-20) - Body ground
      10 kΩ or higher

    4. Reconnect the ECM connector.

    5. Reinstall the EFI fuse.

  1. Check the harness and the connector between the EFI fuse and battery.

    1. Remove the EFI fuse from the engine room relay block.

    2. Disconnect the positive battery terminal.

    3. Check the resistance.

      Standard resistance (Check for open):
      Tester Connections
      Specified Conditions
      Battery positive terminal - EFI fuse (1)
      Below 1 Ω

      Standard resistance (Check for short):
      Tester Connections
      Specified Conditions
      Battery positive terminal or EFI fuse (1) - Body ground
      10 kΩ or higher

    4. Reconnect the positive battery terminal.

    5. Reinstall the EFI fuse.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT BATTERY
  1. Check that the battery is not depleted (Click here).

    OK:
    Battery is not depleted



NG
REPLACE BATTERY
OK


4.CHECK BATTERY TERMINAL
  1. Check that the battery terminals are not loose or corroded.

    OK:
    Battery terminals are not loose or corroded



NG
REPAIR OR REPLACE BATTERY TERMINAL
OK


5.CHECK WHETHER DTC OUTPUT RECURS (DTC P0560)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the Techstream off.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Wait for 5 seconds or more.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.

    Result 
    Display (DTC Output)
    Proceed To
    P0560
    A
    No output
    B



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A

REPLACE ECM (Click here)