DTC P0420 Catalyst System Efficiency Below Threshold (Bank 1) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0420 | The oxygen storage capacity value is less than the standard value under active air fuel ratio control (2 trip detection logic). |
|

| *1 | Exhaust Manifold Assembly | *2 | Air Fuel Ratio Sensor |
| *3 | Front Exhaust Pipe Assembly | *4 | Heated Oxygen Sensor |
| *5 | Tail Exhaust Pipe Assembly | *6 | TWC: Front Catalyst |
| *7 | TWC: Rear Catalyst | - | - |
| Related DTCs | P0420: Catalyst Deterioration |
| Required Sensors/Components (Main) | Air fuel ratio sensor Heated oxygen sensor |
| Required Sensors/Components (Related) | Intake air temperature sensor Mass air flow meter Crankshaft position sensor Engine coolant temperature sensor |
| Frequency of Operation | Once per driving cycle |
| Duration | Approximately 30 seconds |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | P0010 (Camshaft Timing Oil Control Valve) P0011 (VVT System - Advance) P0012 (VVT System - Retard) P0016 (VVT System - Misalignment) P0031, P0032, P101D (Air Fuel Ratio Sensor Heater) P0037, P0038, P102D (Heated Oxygen Sensor Heater) P0136, P0137, P0138, P0139, P0607 (Rear Oxygen Sensor) P0102, P0103 (Mass Air Flow Meter) P0115, P0117, P0118 (Engine Coolant Temperature Sensor) P0125 (Insufficient Coolant Temperature for Closed Loop Fuel Control) P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle Position Sensor) P0171, P0172 (Fuel System) P0301 - P0304 (Misfire) P0335 (Crankshaft Position Sensor) P0340 (Camshaft Position Sensor) P0351 - P0354 (Igniter) P0500 (Vehicle Speed Sensor) P219A (Air Fuel Ratio Imbalance) P2195, P2196, P2237, P2238, P2239, P2252, P2253, P014C, P014D, P015A, P015B (Air Fuel Ratio Sensor) |
| Battery voltage | 11 V or higher |
| Intake air temperature | -10°C (14°F) or higher |
| Engine coolant temperature | 75°C (167°F) or higher |
| Atmospheric pressure | 76 kPa(abs) [570 mmHg(abs)] or higher |
| Idling | OFF |
| Engine speed | Less than 4000 rpm |
| Air fuel ratio sensor status | Activated |
| Fuel system status | Closed loop |
| Engine load | 10% or more, and less than 90%: for Automatic Transaxle 10% or more, and less than 80%: for Manual Transaxle |
| All of the following conditions are met | Condition 1, 2 and 3 |
| 1. Mass air flow rate | 1.7 gm/sec or more, and less than 40 gm/sec: for Automatic Transaxle 1.3 gm/sec or more, and less than 40 gm/sec: for Manual Transaxle |
| 2. Front catalyst temperature (estimated) | 620°C (1148°F) or higher, and less than 805°C (1481°F): for Automatic Transaxle 590°C (1094°F) or higher, and less than 800°C (1472°F): for Manual Transaxle |
| 3. Rear catalyst temperature (estimated) | 480°C (896°F) or higher, and less than 750°C (1382°F): for Automatic Transaxle 470°C (878°F) or higher, and less than 750°C (1382°F): for Manual Transaxle |
| Shift position | 3rd or higher |
| Oxygen Storage Capacity (OSC) of Three-Way Catalytic Converter (TWC) | Less than 0.10742 g |
| Monitor ID | Test ID | Scaling | Unit | Description |
| $21 | $A9 | Multiply by 0.0003 | No dimension | Oxygen storage capacity of catalyst bank 1 |



| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0420) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed to |
| DTC P0420 is output | A |
| DTC P0420 and other DTCs are output | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE INJECTION VOLUME FOR A/F SENSOR) |
Connect the Techstream to the DLC3.
Start the engine and warm it up.
Turn the Techstream on.
Run the engine at an engine speed of 2500 rpm for approximately 90 seconds.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.
Perform the Active Test operation with the engine idling (press the 12.5 or -12.5 button to change the fuel injection volume).
Monitor the voltage outputs of the air fuel ratio sensor and heated oxygen sensor (AFS Voltage B1S1 and O2S B1S2) displayed on the Techstream.
| Techstream Display (Sensor) | Injection Volume | Status | Voltage |
| AFS Voltage B1S1 (Air fuel ratio) | 12.5% | Rich | Below 3.1 V |
| -12.5% | Lean | Higher than 3.4 V | |
| O2S B1S2 (Heated oxygen) | 12.5% | Rich | Higher than 0.55 V |
| -12.5% | Lean | Below 0.4 V |
| Status AFS Voltage B1S1 | Status O2S B1S2 | Actual air fuel ratio, air fuel ratio sensor and heated oxygen sensor condition | Misfire | Main Suspected Trouble Area | Proceed to |
| Lean/Rich | Lean/Rich | Normal | - |
| A |
| Lean | Lean/Rich | Air fuel ratio sensor malfunction | - | Air fuel ratio sensor | B |
| Rich | Lean/Rich | Air fuel ratio sensor malfunction | - | Air fuel ratio sensor | |
| Lean/Rich | Lean | Heated oxygen sensor malfunction | - |
| C |
| Lean/Rich | Rich | Heated oxygen sensor malfunction | - |
| |
| Lean | Lean | Actual air fuel ratio lean | May occur |
| D |
| Rich | Rich | Actual air fuel ratio rich | - |
|
|
| ||||
|
| ||||
|
| ||||
| A | |
| 3.CHECK FOR EXHAUST GAS LEAK |
Check for exhaust gas leaks.
|
| ||||
| OK | |
| 4.REPLACE FRONT EXHAUST PIPE ASSEMBLY (TWC: FRONT CATALYST AND REAR CATALYST) |
Replace the front exhaust pipe assembly (TWC: front catalyst and rear catalyst) (Click here).
| NEXT | ||
| ||
| 5.REPLACE AIR FUEL RATIO SENSOR (BANK 1 SENSOR 1) |
Replace the air fuel ratio sensor (bank 1 sensor 1) (Click here).
|
| ||||
| 6.CHECK FOR EXHAUST GAS LEAK |
Check for exhaust gas leaks.
|
| ||||
| OK | |
| 7.REPLACE HEATED OXYGEN SENSOR (BANK 1 SENSOR 2) |
Replace the heated oxygen sensor (bank 1 sensor 2) (Click here).
|
| ||||
| 8.CHECK FOR EXHAUST GAS LEAK |
Check the exhaust gas leaks.
|
| ||||
| OK | |
| 9.CHECK CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO |
Check the cause of extremely rich or lean actual air fuel ratio, referring to the DTC P0171 Inspection Procedure .
|
| ||||
| 10.REPAIR OR REPLACE EXHAUST GAS LEAK POINT |
Repair or replace exhaust gas leak point (Click here).
| NEXT | |
| 11.CHECK WHETHER DTC OUTPUT RECURS (DTC P0420) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the Techstream on.
Start the engine.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed to |
| DTC P0420 is output | A |
| DTC is not output (No pending DTCs output) | B |
|
| ||||
| A | |
| 12.REPLACE FRONT EXHAUST PIPE ASSEMBLY (TWC: FRONT CATALYST AND REAR CATALYST) |
Replace the front exhaust pipe assembly (TWC: front catalyst and rear catalyst) (Click here).
| NEXT | ||
| ||