Home › Engine / Hybrid System › 1NZ-FE ENGINE CONTROL › SFI SYSTEM (for Sedan)

DTC    P0031    Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1)

DTC    P0032    Oxygen (A/F) Sensor Heater Control Circuit High (Bank 1 Sensor 1)


DESCRIPTION

The A/F sensor generates a voltage* that corresponds to the actual air-fuel ratio. This sensor voltage is used to provide the ECM with feedback so that it can control the air-fuel ratio. The ECM determines the deviation from the stoichiometric air-fuel ratio level, and regulates the fuel injection time. If the A/F sensor malfunctions, the ECM is unable to control the air-fuel ratio accurately.
The A/F sensor is of the planar type and is integrated with the heater, which heats the solid electrolyte (zirconia element). This heater is controlled by the ECM. When the intake air volume is low (the exhaust gas temperature is low), a current flows into the heater to heat the sensor, in order to facilitate accurate air-fuel ratio detection. In addition, the sensor and heater portions are narrower than the conventional type. The heat generated by the heater is conducted to the solid electrolyte through the alumina, and therefore the sensor activation is accelerated.
In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a TWC is used. For the most efficient use of the TWC, the air-fuel ratio must be precisely controlled so that it is always close to the stoichiometric level.
*: Value changes inside the ECM. Since the A/F sensor is the current output element, a current is converted into a voltage inside the ECM. Any measurements taken at the A/F sensor or ECM connectors will show a constant voltage.

A107164E06

HINT:
  1. Although the DTC titles say the oxygen sensor, these DTCs relate to the Air-Fuel Ratio (A/F) sensor.
  2. Sensor 1 refers to the sensor mounted in front of the Three-Way Catalytic Converter (TWC) and located near the engine assembly.
  3. When either of these DTCs are stored, the ECM enters fail-safe mode. The ECM turns off the A/F sensor heater in fail-safe mode. Fail-safe mode continues until the ignition switch is turned to OFF.

  4. The ECM provides a pulse width modulated control circuit to adjust the current through the heater. The A/F sensor heater circuit uses a relay on the +B side of the circuit.


    A112568E01


DTC No.
DTC Detection Condition
Trouble Area
P0031
Air-Fuel Ratio (A/F) sensor heater current less than 0.8 A
(1 trip detection logic)
  1. Open in A/F sensor heater circuit
  2. A/F sensor heater (sensor 1)
  3. Integration relay (EFI relay)
  4. ECM
P0032
Air-Fuel Ratio (A/F) sensor heater current fail
(1 trip detection logic)
  1. Short in A/F sensor heater circuit
  2. A/F sensor heater (sensor 1)
  3. Integration relay (EFI relay)
  4. ECM

CONFIRMATION DRIVING PATTERN


A198819E23

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Start the engine and idle it for 5 minutes or more [B].
  7. With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of 3000 rpm for 1 minute [C].
  8. Idle the engine for 5 minutes or more [D].
  9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [E].
  10. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  12. Input the DTC: P0031 or P0032.
  13. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [E] again.


WIRING DIAGRAM


A239481E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
  1. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  2. Refer to "Data List / Active Test" [A/F Heater Duty #1] (Click here).
  3. Sensor 1 refers to the sensor closest to the engine assembly.
  4. Sensor 2 refers to the sensor farthest away from the engine assembly.
  5. Change the fuel injection volume using the Control the Injection Volume function provided in the Active Test and monitor the air fuel ratio sensor output voltage . If the sensor output voltage does not change (almost no reaction) while performing the Active test, the sensor may be malfunctioning.

1.INSPECT AIR-FUEL RATIO SENSOR (HEATER RESISTANCE)
A085152E32
  1. Disconnect the C23 A/F sensor connector.

  1. Measure the resistance of the A/F sensor connector.

    Standard resistance:
    Tester Connections
    Specified Conditions
    HA1A (1) - +B (2)
    1.8 Ω to 3.4 Ω at 20°C (68°F)
    HA1A (1) - A1A- (4)
    10 kΩ or higher

  1. Reconnect the A/F sensor connector.



NG
REPLACE AIR-FUEL RATIO SENSOR (Click here)
OK


2.CHECK TERMINAL VOLTAGE (+B OF A/F SENSOR)
A079114E11
  1. Disconnect the C23 A/F sensor connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage between the terminals of the C23 A/F sensor connector and body ground.

    Standard voltage:
    Tester Connections
    Specified Conditions
    +B (C23-2) - Body ground
    11 to 14 V

    Result 
    Result
    Proceed to
    NG
    A
    OK
    B

  1. Reconnect the A/F sensor connector.



B
Go to step 5
A


3.INSPECT INTEGRATION RELAY (EFI RELAY)
A107921E05
  1. Remove the integration relay from the engine room relay block.

  1. Inspect the EFI fuse.

    1. Remove the EFI fuse from the integration relay.

    2. Measure the EFI fuse resistance.

      Standard resistance:
      Below 1 Ω

    3. Reinstall the EFI fuse.

  1. Inspect the EFI relay.

    1. Measure the EFI relay resistance.

      Standard resistance:
      Tester Connections
      Specified Conditions
      1C-1 - 1A-4
      10 kΩ or higher
      Below 1 Ω
      (Apply battery voltage between terminals 1A-2 and 1A-3)

  1. Reinstall the integration relay.



NG
REPLACE INTEGRATION RELAY
OK


4.CHECK HARNESS AND CONNECTOR (A/F SENSOR - EFI RELAY)
A112603E01
  1. Disconnect the C23 A/F sensor connector.

  1. Remove the integration relay from the engine room Relay Block (R/B).

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connections
    Specified Conditions
    +B (C23-2) - Engine room R/B (1A-4)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connections
    Specified Conditions
    +B (C23-2) or Engine room
    R/B (1A-4) - Body ground
    10 kΩ or higher

  1. Reconnect the A/F sensor connector.

  1. Reinstall the integration relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK ECM POWER SOURCE CIRCUIT (Click here)  

5.CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM)
A112605E01
  1. Disconnect the C23 A/F sensor connector.

  1. Disconnect the C20 ECM connector.

  1. Check the resistance.

    Standard resistance (Check for open):
    Tester Connections
    Specified Conditions
    HA1A (C23-1) - HA1A (C20-109)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connections
    Specified Conditions
    HA1A (C23-1) or HA1A (C20-109) - Body ground
    10 kΩ or higher

  1. Reconnect the A/F sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK WHETHER DTC OUTPUT RECURS (DTC P0031 OR P0032)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

  1. Read DTCs.


Result 
Display (DTC Output)
Proceed To
No output
A
P0031 or P0032
B


B
REPLACE ECM (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)