DTC P014C A/F Sensor Slow Response - Rich to Lean Bank 1 Sensor 1 |
DTC P014D A/F Sensor Slow Response - Lean to Rich Bank 1 Sensor 1 |
DTC P015A A/F Sensor Delayed Response - Rich to Lean Bank 1 Sensor 1 |
DTC P015B A/F Sensor Delayed Response - Lean to Rich Bank 1 Sensor 1 |
| DTC No. | DTC Detection Condition | Trouble Area |
| P014C | The "Rich to Lean response rate deterioration level*" value is standard or less (2 trip detection logic). |
|
| P014D | The "Lean to Rich response rate deterioration level*" value is standard or more (2 trip detection logic). | |
| P015A | The "Rich to Lean delay level*" value is standard or more (2 trip detection logic). | |
| P015B | The "Lean to Rich delay level*" value is standard or more (2 trip detection logic). |

| Related DTCs | P014C: Air fuel ratio sensor (bank 1) slow response (rich to lean) P014D: Air fuel ratio sensor (bank 1) slow response (lean to rich) P015A: Air fuel ratio sensor (bank 1) delayed response (rich to lean) P015B: Air fuel ratio sensor (bank 1) delayed response (lean to rich) |
| Required Sensors/Components (Main) | Air fuel ratio sensor |
| Required Sensors/Components (Related) | Vehicle speed sensor, crankshaft position sensor |
| Frequency of Operation | Once per driving cycle |
| Duration | 10 to 15 seconds |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | None |
| Active air fuel ratio control | Performing |
| Active air fuel ratio control is performed when the following conditions met | - |
| Battery voltage | 11 V or higher |
| Engine coolant temperature | 75°C (167°F) or higher |
| Idle | OFF |
| Engine speed | 1500 rpm or more, and less than 3100 rpm |
| Air fuel ratio sensor status | Activated |
| Fuel-cut | OFF |
| Engine load | 10% or more, and less than 70% |
| Shift position | 2 or more |
| Catalyst monitor | Not yet |
| Mass air flow | 7 gm/sec or more, and less than 17 gm/sec |
| Rich to Lean Response rate deterioration level | 0.0443 V or less |
| Lean to Rich Response rate deterioration level | -0.0338 V or higher |
| Rich to Lean delay level | 327.68 ms or more |
| Lean to Rich delay level | 327.68 ms or more |
| Monitor ID | Test ID | Scaling | Unit | Description |
| $01 | $93 | Multiply by 0.00012 | V | Rich to Lean response rate deterioration level |
| Monitor ID | Test ID | Scaling | Unit | Description |
| $01 | $94 | Multiply by 0.00012 | V | Lean to Rich response rate deterioration level |
| Monitor ID | Test ID | Scaling | Unit | Description |
| $01 | $95 | Multiply by 0.001 | Second | Rich to Lean delay level |
| Monitor ID | Test ID | Scaling | Unit | Description |
| $01 | $96 | Multiply by 0.001 | Second | Lean to Rich delay level |

| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P014C, P014D, P015A OR P015B) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed to |
| P014C, P014D, P015A or P015B | A |
| P014C, P014D, P015A or P015B and other DTCs | B |
|
| ||||
| A | |
| 2.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE) |
Inspect the air fuel ratio sensor (Click here).
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM) |
Disconnect the air fuel ratio sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| C56-1 (HA1A) - C51-23 (HA1A) | Always | Below 1 Ω |
| C56-3 (A1A+) - C51-133 (A1A+) | Always | Below 1 Ω |
| C56-4 (A1A-) - C51-134 (A1A-) | Always | Below 1 Ω |
| C56-1 (HA1A) or C51-23 (HA1A) - Body ground | Always | 10 kΩ or higher |
| C56-3 (A1A+) or C51-133 (A1A+) - Body ground | Always | 10 kΩ or higher |
| C56-4 (A1A-) or C51-134 (A1A-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.INSPECT AIR FUEL RATIO SENSOR |
Check that the proper air fuel ratio sensor is installed to the vehicle.
|
| ||||
| OK | |
| 5.PERFORM CONFIRMATION DRIVING PATTERN |
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
| NEXT | |
| 6.CHECK WHETHER DTC OUTPUT RECURS (DTC P014C, P014D, P015A OR P015B) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read pending DTCs.
| Result | Proceed to |
| P014C, P014D, P015A or P015B | A |
| No DTCs output (No pending DTCs output) | B |
|
| ||||
| A | |
| 7.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor (Click here).
| NEXT | |
| 8.PERFORM CONFIRMATION DRIVING PATTERN |
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
| NEXT | |
| 9.CHECK WHETHER DTC OUTPUT RECURS (DTC P014C, P014D, P015A OR P015B) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read pending DTCs.
| Result | Proceed to |
| No DTCs output (No pending DTCs output) | A |
| P014C, P014D, P015A or P015B | B |
|
| ||||
| A | ||
| ||