SFI SYSTEM (for Sedan) > Cranking Holding Function Circuit |


| 1.READ VALUE USING TECHSTREAM (STARTER SIGNAL) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Engine and ECT / Starter Signal.
Check the result when the ignition switch is turned to ON and START.
| Ignition Switch Position | Starter Signal |
| ON | OFF |
| START | ON |
| Result | Proceed to |
| NG | A |
| OK | B |
|
| ||||
| A | |
| 2.INSPECT ECM (STSW VOLTAGE) |
![]() |
Disconnect the A21 ECM connector.
Measure the voltage between the terminals of the ECM connector and body ground while cranking the engine.
| Tester Connections | Specified Conditions |
| STSW (A21-14) - Body ground | 11 to 14 V |
| Result | Proceed to |
| Within standard range(A/T) | A |
| Within standard range (M/T) | B |
| Outside standard range | C |
Reconnect the ECM connector.
|
| ||||
|
| ||||
| A | |
| 3.INSPECT ECM (STAR VOLTAGE) |
![]() |
Disconnect the C27 Park/Neutral Position (PNP) switch connector.
Measure the voltage between the terminals of the PNP switch connector and body ground while cranking the engine.
| Tester Connections | Specified Conditions |
| B (C27-4) - Body ground | 11 to 14 V |
Reconnect the PNP switch connector.
|
| ||||
| OK | |
| 4.INSPECT PARK/NEUTRAL POSITION SWITCH |
![]() |
Disconnect the C27 PNP switch connector.
Check the resistance between each terminal shown below when the shift lever is moved to each range.
| Tester Connections | Shift Position | Specified Conditions |
| PL (6) - RB (2) | P | Below 1 Ω |
| L (5) - B (4) | ||
| RL (1) - RB (2) | R | |
| NL (9) - RB (2) | N | |
| L (5) - B (4) | ||
| DL (7) - RB (2) | D | |
| 2L (3) - RB (2) | 2 | |
| LL (8) - RB (2) | L |
Reconnect the PNP switch connector.
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM) |
![]() |
Disconnect the C27 PNP switch connector.
Disconnect the A21 ECM connector.
Check the resistance.
| Tester Connections | Specified Conditions |
| L (C27-5) - STA (A21-48) | Below 1 Ω |
| Tester Connections | Specified Conditions |
| L (C27-5) or STA (A21-48) - Body ground | 10 kΩ or higher |
Reconnect the PNP switch connector.
Reconnect the ECM connector.
|
| ||||
| OK | ||
| ||
| 6.INSPECT ECM (STAR VOLTAGE) |
![]() |
Disconnect the A16 clutch start switch connector.
Measure the voltage between the terminals of the clutch start switch connector and body ground while cranking the engine.
| Tester Connections | Specified Conditions |
| B (A16-2) - Body ground | 11 to 14 V |
Reconnect the clutch start switch connector.
|
| ||||
| OK | |
| 7.INSPECT CLUTCH START SWITCH |
![]() |
Disconnect the A16 clutch start switch connector.
Check the resistance between the terminals of the clutch start switch.
| Switch Positions | Specified Conditions |
| Pushed in | Below 1 Ω |
| Released | 10 kΩ or higher |
Reconnect the clutch start switch connector.
|
| ||||
| OK | |
| 8.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH - ECM) |
![]() |
Disconnect the A16 clutch start switch connector.
Disconnect the A21 ECM connector.
Check the resistance.
| Tester Connections | Specified Conditions |
| L (A16-1) - STA (A21-48) | Below 1 Ω |
| Tester Connections | Specified Conditions |
| L (A16-1) or STA (A21-48) - Body ground | 10 kΩ or higher |
Reconnect the clutch start switch connector.
Reconnect the ECM connector.
|
| ||||
| OK | ||
| ||
| 9.INSPECT IGNITION SWITCH |
![]() |
Disconnect the D8 ignition switch connector.
Check the resistance between the terminals shown below.
| Key Positions | Tester Connections | Specified Conditions |
| LOCK | - | 10 kΩ or higher |
| ACC | 2 - 4 | Below 1 Ω |
| ON | 1 - 2 - 4 | |
| 5 - 6 | ||
| START | 1 - 3 - 4 | |
| 5 - 6 - 7 |
Reconnect the ignition switch connector.
|
| ||||
| OK | ||
| ||
| 10.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH - PARK/NEUTRAL POSITION SWITCH - ECM) |
![]() |
Disconnect the D8 ignition switch connector.
Disconnect the C27 PNP switch connector.
Disconnect the C20 ECM connector.
Check the resistance.
| Tester Connections | Specified Conditions |
| ST2 (D8-7) - B (C27-4) | Below 1 Ω |
| STAR (C20-52) - B (C27-4) | |
| STAR (C20-52) - L (C27-5) |
| Tester Connections | Specified Conditions |
| ST2 (D8-7) or B (C27-4) - Body ground | 10 kΩ or higher |
| STAR (C20-52) or B (C27-4) - Body ground | |
| STAR (C20-52) or L (C27-5) - Body ground |
Reconnect the ignition switch connector.
Reconnect the PNP switch connector.
Reconnect the ECM connector.
|
| ||||
| OK | ||
| ||
| 11.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH - CLUTCH START SWITCH - ECM) |
![]() |
Disconnect the D8 ignition switch connector.
Disconnect the A16 clutch start switch connector.
Disconnect the C20 ECM connector.
Check the resistance.
| Tester Connections | Specified Conditions |
| ST2 (D8-7) - B (A16-2) | Below 1 Ω |
| STAR (C20-52) - B (A16-2) | |
| STAR (C20-52) - L (A16-1) |
| Tester Connections | Specified Conditions |
| ST2 (D8-7) or B (A16-2) - Body ground | 10 kΩ or higher |
| STAR (C20-52) or B (A16-2) - Body ground | |
| STAR (C20-52) or L (A16-1) - Body ground |
Reconnect the ignition switch connector.
Reconnect the clutch start switch connector.
Reconnect the ECM connector.
|
| ||||
| OK | ||
| ||
| 12.INSPECT BATTERY |
Check that the battery is not depleted (Click here).
|
| ||||
| OK | |
| 13.CHECK BATTERY TERMINAL |
Check that the battery terminals are not loose or corroded.
|
| ||||
| OK | |
| 14.CHECK HARNESS AND CONNECTOR (PNP SWITCH OR CLUTCH START SWITCH - ST RELAY) |
![]() |
Remove the ST relay from the engine room relay block.
Disconnect the C27 PNP switch connector (A/T).
Disconnect the A16 clutch start switch connector (M/T).
Check the resistance.
| Tester Connections | Specified Conditions |
| L (C27-5) - ST relay (2) | Below 1 Ω |
| L (A16-1) - ST relay (2) | |
| ST relay (1) - Body ground |
| Tester Connections | Specified Conditions |
| L (C27-5) or ST relay (2) - Body ground | 10 kΩ or higher |
| L (A16-1) or ST relay (2) - Body ground |
Reinstall the ST relay.
Reconnect the PNP switch connector (A/T).
Reconnect the clutch start switch connector (M/T).
|
| ||||
| OK | ||
| ||