Home › Engine / Hybrid System › 1NZ-FE ENGINE CONTROL › SFI SYSTEM (for Hatchback)

DTC    P0351    Ignition Coil "A" Primary / Secondary Circuit

DTC    P0352    Ignition Coil "B" Primary / Secondary Circuit

DTC    P0353    Ignition Coil "C" Primary / Secondary Circuit

DTC    P0354    Ignition Coil "D" Primary / Secondary Circuit


DESCRIPTION

HINT:
  1. These DTCs indicate malfunctions relating to the primary circuit.
  2. If DTC P0351 is output, check the No. 1 ignition coil (No. 1 cylinder) circuit.
  3. If DTC P0352 is output, check the No. 1 ignition coil (No. 2 cylinder) circuit.
  4. If DTC P0353 is output, check the No. 1 ignition coil (No. 3 cylinder) circuit.
  5. If DTC P0354 is output, check the No. 1 ignition coil (No. 4 cylinder) circuit.

A Direct Ignition System (DIS) is used on this vehicle.
The DIS is a 1-cylinder ignition system in which each cylinder is ignited by one ignition coil and one spark plug is connected to the end of each secondary wiring. A powerful voltage, generated in the secondary wiring, is applied directly to each spark plug. The spark of the spark plugs passes from the center electrode to the ground electrodes.
The ECM determines the ignition timing and transmits the ignition (IGT) signals to each cylinder. Using the IGT signal, the ECM turns the power transistor inside the igniter on and off. The power transistor, in turn, switches on and off the current to the primary coil. When the current to the primary coil is cut off, a powerful voltage is generated in the secondary coil. This voltage is applied to the spark plugs, causing them to spark inside the cylinders. As the ECM cuts the current to the primary coil, the igniter sends back an ignition confirmation (IGF) signal to the ECM for each cylinder ignition.

A256693E04


DTC No.
DTC Detection Condition
Trouble Area
P0351
P0352
P0353
P0354
No IGF signal to the ECM while the engine is running (1 trip detection logic).
  1. Ignition system
  2. Open or short in IGF1 or IGT circuit (1 to 4) between No. 1 ignition coil and ECM
  3. No. 1 ignition coil (No. 1 to No. 4 cylinder)
  4. ECM

  1. A033447E05
  2. Reference: Inspection using an oscilloscope.
  3. While cranking or idling the engine, check the waveform between terminals IGT (1 to 4) and E1, and IGF1 and E1 of the ECM connector.
    ECM Terminal Name
    CH1: Between IGT (1 to 4) and E1
    CH2: Between IGF1 and E1
    Tester Range
    5 V/DIV., 20 ms./DIV.
    Condition
    Idling

MONITOR DESCRIPTION


A212405E16

If the ECM does not receive any IGF signals despite transmitting the IGT signal, it interprets this as a fault in the igniter and stores a DTC.
If the malfunction is not repaired successfully, a DTC is stored 1 second after the engine is next started.

MONITOR STRATEGY


Related DTCs
P0351: Igniter (Cylinder 1) Malfunction
P0352: Igniter (Cylinder 2) Malfunction
P0353: Igniter (Cylinder 3) Malfunction
P0354: Igniter (Cylinder 4) Malfunction
Required Sensors/Components (Main)
Igniter
Required Sensors/Components (Related)
Crankshaft position sensor
Frequency of Operation
Continuous
Duration
-
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
None
Spark cut
Not operating
Either of following conditions met
A or B
A. Engine speed
1500 rpm or less
B. Starter
OFF
Either of following conditions met
C or D
C. Both of following conditions met
-
(a) Engine speed
500 rpm or less
(b) Battery voltage
6 V or higher
D. All of following conditions met
-
(a) Engine speed
More than 500 rpm
(b) Battery voltage
10 V or higher
(c) Number of sparks after CPU reset
5 sparks or more

TYPICAL MALFUNCTION THRESHOLDS


All of the following conditions are met
Condition A, B, C and D
A. Ignition signal fail counter
More than 2 times
B. Time after condition A is met
0.256 seconds or more
C. Ignition signal fail counter after condition B is met
More than 2 times
D. Ignition switch
ON

COMPONENT OPERATING RANGE


Following condition is met
2 times or more
Confirmed ignition signal
Signal input

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on.
  6. Start the engine.
  7. Idle the engine for 10 seconds or more [A].
  8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].
  9. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  11. Input the DTC: P0351, P0352, P0353 or P0354.
  12. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [A] through [B] again.

  13. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM


A259489E03


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK HARNESS AND CONNECTOR (NO. 1 IGNITION COIL - BODY GROUND)
  1. Disconnect the No. 1 ignition coil connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    C47-4 (GND) - Body ground
    Always
    Below 1 Ω
    C48-4 (GND) - Body ground
    Always
    Below 1 Ω
    C49-4 (GND) - Body ground
    Always
    Below 1 Ω
    C50-4 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT TERMINAL VOLTAGE (POWER SOURCE OF NO. 1 IGNITION COIL)


    A115969E95
  1. Disconnect the No. 1 ignition coil connectors.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C47-1 (+B) - C47-4 (GND)
    Ignition switch ON
    11 to 14 V
    C48-1 (+B) - C48-4 (GND)
    Ignition switch ON
    11 to 14 V
    C49-1 (+B) - C49-4 (GND)
    Ignition switch ON
    11 to 14 V
    C50-1 (+B) - C50-4 (GND)
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to No. 1 Ignition Coil)



NG
Go to step 5
OK


3.CHECK HARNESS AND CONNECTOR (NO. 1 IGNITION COIL - ECM)
  1. Disconnect the No. 1 ignition coil connectors.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    C47-2 (IGF) - C51-102 (IGF1)
    Always
    Below 1 Ω
    C48-2 (IGF) - C51-102 (IGF1)
    Always
    Below 1 Ω
    C49-2 (IGF) - C51-102 (IGF1)
    Always
    Below 1 Ω
    C50-2 (IGF) - C51-102 (IGF1)
    Always
    Below 1 Ω
    C47-3 (IGT1) - C51-57 (IGT1)
    Always
    Below 1 Ω
    C48-3 (IGT2) - C51-56 (IGT2)
    Always
    Below 1 Ω
    C49-3 (IGT3) - C51-55 (IGT3)
    Always
    Below 1 Ω
    C50-3 (IGT4) - C51-54 (IGT4)
    Always
    Below 1 Ω
    C47-2 (IGF) or C51-102 (IGF1) - Body ground
    Always
    10 kΩ or higher
    C48-2 (IGF) or C51-102 (IGF1) - Body ground
    Always
    10 kΩ or higher
    C49-2 (IGF) or C51-102 (IGF1) - Body ground
    Always
    10 kΩ or higher
    C50-2 (IGF) or C51-102 (IGF1) - Body ground
    Always
    10 kΩ or higher
    C47-3 (IGT1) or C51-57 (IGT1) - Body ground
    Always
    10 kΩ or higher
    C48-3 (IGT2) or C51-56 (IGT2) - Body ground
    Always
    10 kΩ or higher
    C49-3 (IGT3) or C51-55 (IGT3) - Body ground
    Always
    10 kΩ or higher
    C50-3 (IGT4) or C51-54 (IGT4) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353 OR P0354)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Shuffle the arrangement of the ignition coils (among No. 1 to No. 4 cylinders).

    NOTICE:
    Do not change the location of the connectors.

  1. Perform a simulation test.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    Same DTC output
    A
    Different ignition coil DTC output
    B

    HINT:
    Perform "Inspection After Repair" after replacing the No. 1 ignition coil (Click here).



B
REPLACE NO. 1 IGNITION COIL (Click here)
A

REPLACE ECM (Click here)  

5.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - NO. 1 IGNITION COIL)
  1. Disconnect the No. 1 ignition coil connectors.

  1. Remove the No. 1 integration relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    C47-1 (+B) - 1E-2
    Always
    Below 1 Ω
    C48-1 (+B) - 1E-2
    Always
    Below 1 Ω
    C49-1 (+B) - 1E-2
    Always
    Below 1 Ω
    C50-1 (+B) - 1E-2
    Always
    Below 1 Ω
    C47-1 (+B) or 1E-2 - Body ground
    Always
    10 kΩ or higher
    C48-1 (+B) or 1E-2 - Body ground
    Always
    10 kΩ or higher
    C49-1 (+B) or 1E-2 - Body ground
    Always
    10 kΩ or higher
    C50-1 (+B) or 1E-2 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK ECM POWER SOURCE CIRCUIT (Click here)