Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM (for Sedan)

LIGHTING SYSTEM (for Sedan) > ACC Signal Circuit


DESCRIPTION

This circuit detects the ignition switch ACC or off condition, and sends it to the main body ECU.

WIRING DIAGRAM


E225980E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.READ VALUE USING TECHSTREAM
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Main Body / Data List.

  1. According to the display on the Techstream, read the Data List.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    ACC SW
    Ignition switch signal/
    ON or OFF
    ON: Ignition switch ACC
    OFF: Ignition switch off
    -

    OK:
    Normal conditions listed above are displayed.



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.PERFORM ACTIVE TEST USING TECHSTREAM
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test.

  1. According to the display on the Techstream, perform the Active Test.

    Engine and ECT 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Activate the ACC CUT Relay
    ACC CUT relay
    ON or OFF
    Test possible when engine stopped

    OK:
    ACC CUT relay operating sound occurs.



NG
Go to step 5
OK


3.CHECK HARNESS AND CONNECTOR (ACC CUT RELAY - IGNITION SWITCH)


    E225981E01
  1. Remove the ACC CUT relay.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D45-3 - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *1
    ACC CUT Relay Holder



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (ACC CUT RELAY - MAIN BODY ECU)
  1. Remove the ACC CUT relay.

  1. Disconnect the 4F main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D45-4 - 4F-5
    Always
    Below 1 Ω
    D45-4 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU 

5.INSPECT ACC CUT RELAY
  1. Inspect the ACC CUT relay (Click here).



NG
REPLACE ACC CUT RELAY
OK


6.CHECK HARNESS AND CONNECTOR (ACC CUT RELAY - BATTERY)


    E225981E01
  1. Remove the ACC CUT relay.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D45-2 - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *1
    ACC CUT Relay Holder



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK HARNESS AND CONNECTOR (ACC CUT RELAY - ECM)
  1. Remove the ACC CUT relay.

  1. Disconnect the A21 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D45-1 - A21-13 (ACCR)
    Always
    Below 1 Ω
    D45-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)