DTC P0451 Evaporative Emission Control System Pressure Sensor Range / Performance |
DTC P0452 Evaporative Emission Control System Pressure Sensor / Switch Low Input |
DTC P0453 Evaporative Emission Control System Pressure Sensor / Switch High Input |
| DTC No. | Monitoring Item | Malfunction Detection Condition | Trouble Area | Detection Timing | Detection Logic |
| P0451 | Canister pressure sensor abnormal voltage fluctuation | Sensor output voltage fluctuates frequently in a certain time period. |
|
| 2 trip |
| Canister pressure sensor constant voltage | Sensor output voltage does not vary in a certain time period. |
| 2 trip | ||
| P0452 | Canister pressure sensor low input | EVAP pressure sensor less than 42.11009 kPa(abs) [315.85178 mmHg(abs)] for 0.5 seconds |
| 1 trip | |
| P0453 | Canister pressure sensor high input | EVAP pressure sensor more than 123.76147 kPa(abs) [928.28776 mmHg(abs)] for 0.5 seconds |
| 1 trip |

| Required Sensors/Components | Canister pump module |
| Frequency of Operation | Continuous |
| Duration | 0.5 seconds: P0452 and P0453 Within 2 minutes: P0451 (sensor stuck) Less than 15 seconds: P0451 (sensor noise) |
| MIL Operation | Immediate: P0452 and P0453 2 driving cycles: P0451 |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | None |
| Atmospheric pressure (absolute pressure) | 70 kPa(abs) [525 mmHg(abs)] or higher, and less than 110 kPa(abs) [825 mmHg(abs)] |
| Battery voltage | 10.5 V or higher |
| Intake air temperature | 4.4°C (40°F) or higher, and less than 35°C (95°F) |
| Canister pressure sensor malfunction (P0452, P0453) | Not detected |
| Either of following conditions met | A or B |
| A. Engine condition | Running |
| B. Time after key-off | 5, 7 or 9.5 hours |
| Monitor runs whenever following DTCs not present | None |
| Battery voltage | 10.5 V or higher |
| Intake air temperature | 4.4°C (40°F) or higher, and less than 35°C (95°F) |
| Canister pressure sensor malfunction (P0452, P0453) | Not detected |
| Atmospheric pressure (absolute pressure) | Less than 70 kPa(abs) [525 mmHg(abs)], and 110 kPa(abs) [825 mmHg(abs)] or higher |
| Time after key-off | 5, 7 or 9.5 hours |
| Monitor runs whenever following DTCs not present | None |
| Ignition switch | ON |
| Battery voltage | 8 V or higher |
| Starter | OFF |
| Frequency that EVAP pressure change 0.3 kPa(gauge) [2.25 mmHg(gauge)] or higher | 10 times or more in 10 seconds |
| EVAP pressure change during reference pressure measurement | Below 0.65 kPa(gauge) [4.876 mmHg(gauge)] |
| EVAP pressure | Below 42.11009 kPa(abs) [315.85178 mmHg(abs)] |
| EVAP pressure | Higher than 123.76147 kPa(abs) [928.28776 mmHg(abs)] |
| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.CONFIRM DTC AND EVAP PRESSURE |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON (do not start the engine).
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
Enter the following menus: Powertrain / Engine and ECT / Data List / Vapor Pressure Pump.
Read the EVAP (Evaporative Emission) pressure displayed on the Techstream.
| Display (DTC Output) | Test Result | Suspected Trouble Area | Proceed to |
| P0451 | - | Canister pressure sensor | C |
| P0452 | Below 42.11009 kPa(abs) [315.85178 mmHg(abs)] |
| A |
| P0453 | Higher than 123.76147 kPa(abs) [928.28776 mmHg(abs)] |
| B |
|
| ||||
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM) |
Turn the ignition switch off.
Disconnect the A72 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Suspected Trouble Area | Proceed to |
| A72-35 (PPMP) - Body ground | Always | Below 10 Ω |
| A |
| 10 kΩ or higher |
| B |
|
| ||||
| A | |
| 3.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM) |
Disconnect the J70 canister pump module connector.
Disconnect the A72 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Suspected Trouble Area | Proceed to |
| A72-35 (PPMP) - Body ground | Always | 10 kΩ or higher | Short in canister pressure sensor circuit | A |
| Below 10 Ω | Short in wire harness/connector (ECM - Canister pressure sensor) | B |
|
| ||||
|
| ||||
| 4.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM) |
![]() |
Disconnect the canister pump module connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| J70-8 (SGND) - Body ground | Always | 100 Ω or less |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J70-6 (VCC) - Body ground | Ignition switch ON | 4.5 to 5.5 V |
| J70-7 (VOUT) - Body ground | Ignition switch ON | 4.5 to 5.5 V |
| Test Result | Suspected Trouble Area | Proceed to |
| Voltage and resistance within standard ranges | Open in canister pressure sensor circuit | A |
| Voltage and/or resistance outside standard ranges | Open in wire harness/connector (ECM - Canister pressure sensor) | B |
| *a | Front view of wire harness connector (to Canister Pump Module) |
|
| ||||
| A | |
| 5.REPLACE CANISTER |
Replace the canister (Click here).

| *1 | Fuel Tank Vent Hose | *2 | Air Inlet Port (behind Filler Pipe Flange Plate) |
| *3 | Vent Hose | *4 | Fuel Tank |
| *5 | Canister | *6 | Canister Filter |
| *a | Inspection Area (Check for disconnection and/or cracks) | - | - |
|
| ||||
| 6.REPAIR OR REPLACE HARNESS OR CONNECTOR (CANISTER - ECM) |
|
| ||||
| 7.REPLACE ECM |
Replace the ECM (Click here).
| NEXT | |
| 8.CHECK WHETHER DTC OUTPUT RECURS (AFTER REPAIR) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the Techstream on.
Perform the Evaporative System Check using the Techstream, referring to the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0451, P0452 or P0453.
Check the DTC judgment result.
| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| NEXT | ||
| ||