Home › Engine / Hybrid System › 1NZ-FE ENGINE CONTROL › SFI SYSTEM (for Sedan)

DTC    P0500    Vehicle Speed Sensor "A"


DESCRIPTION

The vehicle speed is detected using the No. 1 vehicle speed sensor. The No. 1 vehicle speed sensor transmits a 4-pulse signal for every revolution of the rotor shaft, which is rotated by the transaxle output shaft via the driven gear. The 4-pulse signal is converted into a more precise rectangular waveform by the waveform shaping circuit inside the combination meter. The signal is then transmitted to the ECM. The ECM determines the vehicle speed based on the frequency of the pulse signal.

A112641E02


DTC No.
DTC Detection Condition
Trouble Area
P0500
While vehicle being driven, no vehicle speed sensor signal transmitted to ECM
(1 trip detection logic: Automatic transaxle)
(2 trip detection logic: Manual transaxle)
  1. Open or short in speed signal circuit
  2. Vehicle speed sensor
  3. Combination meter
  4. ECM
  5. Wire harness or connector

WIRING DIAGRAM


A234470E04


INSPECTION PROCEDURE

HINT:
  1. Various systems use the vehicle speed signal distributed from the combination meter. Check all the components possibly related to speed signal.
  2. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK OPERATION OF SPEEDOMETER
  1. Drive the vehicle and check whether the operation of the speedometer in the combination meter is normal.

    OK:
    The operation of the speedometer is normal.

    HINT:
    1. The vehicle speed sensor is operating normally if the speedometer reading is normal.
    2. If the speedometer does not operate, check it by following the procedure described in Speedometer Malfunction (Click here).



NG
GO TO MALFUNCTION IN SPEEDOMETER
OK


2.READ VALUE USING TECHSTREAM (VEHICLE SPEED)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Vehicle Speed.

  1. Drive the vehicle.

  1. Read the value displayed on the Techstream.

    OK:
    Vehicle speeds displayed on the Techstream and speedometer display are equal.



NG
Go to step 3
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)
  1. Disconnect the combination meter connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    D1-16 - A21-8 (SPD)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    D1-16 or A21-8 (SPD) - Body ground
    Always
    10 kΩ or higher

    HINT:
    If the wire has a short, check the speed signal circuit in other systems related to the vehicle speed signal (e.g. tire pressure warning system, audio system, etc.).

  1. Reconnect the combination meter connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (OTHER SYSTEMS RELATED TO SPEED SIGNAL)
OK


4.CHECK COMBINATION METER (VOLTAGE)
A239097E01
  1. Disconnect the combination meter connector.

    HINT:
    Disconnect the ECU connectors on the other systems related to the speed signal (but the ECM connectors must be connected).

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D1-16 - Body ground
    Ignition switch ON
    4.5 to 5.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Combination Meter)

  1. Reconnect the combination meter connector.



NG
REPLACE ECM (Click here)
OK


5.INSPECT COMBINATION METER (SPD SIGNAL OUTPUT WAVEFORM)


    A112586E03
  1. Remove the combination meter assembly (Click here).

  1. Connect the combination meter connector.

  1. Move the shift lever to the neutral position.

  1. Jack up the vehicle.

  1. Turn the ignition switch to ON.

  1. Check the voltage between the terminal of the combination meter and the body ground while the wheel is turned slowly.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D1-16 - Body ground
    Ignition switch ON
    (Turn wheel slowly)
    Voltage generated intermittently

    Text in Illustration  
    *a
    Component with wire harness connected
    (Combination Meter)
    *b
    Turn Wheel

    HINT:
    The output voltage should fluctuate up and down, similarly to the diagram, when the wheel is turned slowly.

  1. Reinstall the combination meter assembly (Click here).



NG
Go to step 6
OK

REPLACE ECM (Click here)  

6.INSPECT COMBINATION METER (SPD SIGNAL INPUT WAVEFORM)


    A112586E04
  1. Remove the combination meter assembly (Click here).

  1. Connect the combination meter connector.

  1. Move the shift lever to the neutral position.

  1. Jack up the vehicle.

  1. Turn the ignition switch to ON.

  1. Check the voltage between the terminal of the combination meter and the body ground while the wheel is turned slowly.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D1-17 - Body ground
    Ignition switch ON
    (Turn wheel slowly)
    Voltage generated intermittently

    Text in Illustration  
    *a
    Component with wire harness connected
    (Combination Meter)
    *b
    Turn Wheel

    HINT:
    The output voltage should fluctuate up and down, similarly to the diagram, when the wheel is turned slowly.

  1. Reinstall the combination meter assembly (Click here).

Result 
Result
Proceed to
OK
A
NG
B


B
Go to step 7
A

REPLACE COMBINATION METER (Click here)  

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER - VEHICLE SPEED SENSOR)
  1. Disconnect the combination meter connector.

  1. Disconnect the vehicle speed sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    D1-17 - C21-3 (SI)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    D1-17 or C21-3 (SI) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the combination meter connector.

  1. Reconnect the vehicle speed sensor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE VEHICLE SPEED SENSOR