DTC P0500 Vehicle Speed Sensor "A" |


| DTC No. | DTC Detection Condition | Trouble Area |
| P0500 | While vehicle is being driven, no vehicle speed sensor signal is transmitted to ECM. (1 trip detection logic: Automatic transaxle) (2 trip detection logic: Manual transaxle) |
|
| Related DTCs | P0500: Vehicle speed sensor "A" pulse input error |
| Required Sensors/Components (Main) | Combination meter assembly Vehicle speed sensor Skid control ECU |
| Required Sensors/Components (Related) | Park/neutral position switch Engine coolant temperature sensor Crankshaft position sensor Throttle position sensor Mass air flow meter |
| Frequency of Operation | Continuous |
| Duration | 2 seconds: Automatic Transaxle, Intake air temperature -10°C (14°F) or more 8 seconds: Automatic Transaxle, Intake air temperature less than -10°C (14°F) 4.6 seconds: Manual Transaxle |
| MIL Operation | Immediate: Automatic Transaxle 2 driving cycles: Manual Transaxle |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | None |
| Time after ignition switch turned from OFF to ON | 3 seconds or more |
| Battery voltage | 8 V or higher |
| Ignition switch | ON |
| Starter | OFF |
| Fuel-cut | ON |
| Idle | ON |
| Monitor runs whenever following DTCs not present | None |
| Ignition Switch | ON |
| Time after ignition switch OFF to ON | 3 seconds or more |
| Battery voltage | 8 V or higher |
| Starter | OFF |
| Either of following conditions (a) or (b) met: | - |
| (a) Following conditions 1 and 2 met: | - |
| 1. Engine coolant temperature and engine coolant temperature sensor | 20°C (68°F) or more, and sensor does not malfunction (P0115 or P00117, P0118, P0125) |
| 2. Time after park/neutral position switch ON to OFF | 10 seconds or more |
| (b) Following conditions 1 and 2 met: | - |
| 1. Engine coolant temperature and engine coolant temperature sensor | Less than 20°C (68°F), or sensor malfunctions (P0115 or P0117, P0118, P0125) |
| 2. Time after park/neutral position switch ON to OFF | 30 seconds or more |
| Throttle position sensor fail (P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135) | Not detected |
| Engine speed | 2090 rpm or more (varies with throttle valve opening angle) |
| Fuel cut at high engine speed | Not executing |
| Throttle position sensor learning | Completed |
| Vehicle speed sensor signal | No pulse input |

| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.READ VALUE USING TECHSTREAM (VEHICLE SPEED) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Vehicle Speed.
Drive the vehicle and confirm that the operation of the speedometer in the combination meter is normal.
Read the value displayed on the Techstream while driving the vehicle.
| Result | Proceed to |
| Values displayed on Techstream and speedometer display not equal | A |
| Values displayed on Techstream and speedometer display equal | B |
|
| ||||
| A | |
| 2.CHECK COMBINATION METER SYSTEM (SPEED SIGNAL CIRCUIT) |
Check the circuits that send vehicle speed signals to this system in the meter system (Click here).
| NEXT | |
| 3.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the Techstream on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
| NEXT | ||
| ||