METER / GAUGE SYSTEM (for Hatchback) > Speed Signal Circuit |

| 1.INSPECT COMBINATION METER ASSEMBLY (INPUT VOLTAGE) |
![]() |
Disconnect the D100 combination meter assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D100-6 (+S) - Body ground | Ignition switch ON | 4.5 to 14 V |
| *a | Front view of wire harness connector (to Combination Meter Assembly) |
Reconnect the combination meter assembly connector.
|
| ||||
| OK | |
| 2.SYSTEM CHECK |
Check the vehicle specifications.
| Result | Proceed to |
| w/ ABS | A |
| w/o ABS | B |
|
| ||||
| A | |
| 3.INSPECT COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE) |
![]() |
Disconnect the A70*1 or A71*2 brake actuator assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A70-11 (SP1)*1 - Body ground A71-22 (SP1)*2 - Body ground | Ignition switch ON | 11 to 14 V |
| *A | w/ VSC |
| *B | w/o VSC |
| *a | Front view of wire harness connector (to brake actuator assembly) |
Reconnect the A70*1 or A71*2 brake actuator assembly connector.
|
| ||||
| OK | |
| 4.INSPECT COMBINATION METER ASSEMBLY (INPUT WAVEFORM) |
![]() |
Check the input waveform.
Remove the combination meter assembly with the connector(s) still connected.
Connect an oscilloscope to terminal D100-5 (SI) and body ground.
Turn the ignition switch to ON.
Turn the wheel slowly.
Check the signal waveform according to the condition(s) in the table below.
| Item | Condition |
| Tool setting | 5 V/DIV., 20 ms./DIV. |
| Condition | Driving at approx. 20 km/h |
| *a | Component with harness connected (Combination Meter Assembly) |
| *b | Waveform |
|
| ||||
| OK | ||
| ||
| 5.INSPECT COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE) |
![]() |
Disconnect the C57 speedometer sensor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| C57-3 (SI) - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector (to Speedometer Sensor) |
Reconnect the C57 speedometer sensor connector.
|
| ||||
| OK | |
| 6.INSPECT COMBINATION METER ASSEMBLY (INPUT WAVEFORM) |
![]() |
Check the input waveform.
Remove the combination meter assembly with the connector(s) still connected.
Connect an oscilloscope to terminal D100-5 (SI) and body ground.
Turn the ignition switch to ON.
Turn the wheel slowly.
Check the signal waveform according to the condition(s) in the table below.
| Item | Condition |
| Tool setting | 5 V/DIV., 20 ms./DIV. |
| Vehicle condition | Driving at approx. 20 km/h (12 mph) |
| *a | Component with harness connected (Combination Meter Assembly) |
| *b | Waveform |
|
| ||||
| OK | ||
| ||
| 7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY) |
Disconnect the D100 combination meter assembly connector.
Disconnect the A70*1 or A71*2 brake actuator assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D100-5 (SI) - A70-11 (SP1)*1 D100-5 (SI) - A71-22 (SP1)*2 | Always | Below 1 Ω |
| D100-5 (SI) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 8.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - SPEEDOMETER SENSOR) |
Disconnect the D100 combination meter assembly connector.
Disconnect the C57 speedometer sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| C57-3 (SI) - D100-5 (SI) | Always | Below 1 Ω |
| C57-3 (SI) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 9.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY) |
Disconnect the 3B instrument panel junction block assembly connector.
Disconnect the D100 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D100-6 (+S) - 3B-15 | Always | Below 1 Ω |
| D100-6 (+S) - Body ground | Always | 10 kΩ or higher |
Reconnect the 3B instrument panel junction block assembly connector.
Reconnect the D100 combination meter assembly connector.
|
| ||||
| OK | |
| 10.INSPECT ECM |
![]() |
Disconnect the 3C instrument panel junction block assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 3C-39 - Body ground | Ignition switch ON | 4.5 to 14 V |
| *a | Front view of wire harness connector (to Instrument Panel Junction Block Assembly) |
Reconnect the 3C instrument panel junction block assembly connector.
|
| ||||
| OK | |
| 11.SYSTEM CHECK |
Check the vehicle specifications.
| Result | Proceed to |
| w/ ABS | A |
| w/o ABS | B |
|
| ||||
| A | |
| 12.INSPECT POWER STEERING ECU ASSEMBLY |
![]() |
Disconnect the 3A instrument panel junction block assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 3A-37 - Body ground | Ignition switch ON | 4.5 to 14 V |
| *a | Front view of wire harness connector (to Instrument Panel Junction Block Assembly) |
Reconnect the 3A instrument panel junction block assembly connector.
|
| ||||
| OK | ||
| ||
| 13.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - ECM) |
Disconnect the 3C instrument panel junction block assembly connector.
Disconnect the A72 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3C-39 - A72-44 (SPD) | Always | Below 1 Ω |
| 3C-39 - Body ground | Always | 10 kΩ or higher |
Reconnect the 3C instrument panel junction block assembly connector.
Reconnect the A72 ECM connector.
|
| ||||
| OK | ||
| ||
| 14.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - POWER STEERING ECU ASSEMBLY) |
Disconnect the 3A instrument panel junction block assembly connector.
Disconnect the D104 power steering ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3A-37 - D104-2 (SPD) | Always | Below 1 Ω |
| 3A-37 - Body ground | Always | 10 kΩ or higher |
Reconnect the 3A instrument panel junction block assembly connector.
Reconnect the D104 power steering ECU connector.
|
| ||||
| OK | ||
| ||