DTC B1790 Center Airbag Sensor Assembly Communication Circuit Malfunction |
| DTC Code | DTC Detection Condition | Trouble Area |
| B1790 | One of following conditions is met:
|
|

| 1.CHECK FOR DTC |
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Using the Techstream, check for DTCs of the occupant classification ECU (Click here).
|
| ||||
| OK | ||
| ||
| 2.CHECK CONNECTION OF CONNECTOR |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connectors are properly connected to the occupant classification ECU and airbag sensor assembly. Also check that the connectors that link the front seat wire RH and floor wire are properly connected.
|
| ||||
| OK | |
| 3.CHECK CONNECTOR |
Check that the connectors (on the airbag sensor assembly side, occupant classification ECU side, front seat wire RH side and floor wire side) are not damaged.
|
| ||||
| OK | |
| 4.CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT |

| *1 | Occupant Classification ECU | *2 | Airbag Sensor Assembly |
| *3 | Service Wire | - | - |
| *a | Front view of wire harness connector (to Occupant Classification ECU) | *b | Rear view of wire harness connector (to Airbag Sensor Assembly) |
| *c | Connector E | *d | Connector B |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| X4-7 - Body ground | Ignition switch ON | Below 1 V |
| X4-4 - Body ground |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Using a service wire, connect terminals 16 (FSR+) and 24 (FSR-) of connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| X4-7 - X4-4 | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| X4-7 - X4-4 | Always | 1 MΩ or higher |
| X4-7 - Body ground | ||
| X4-4 - Body ground |
|
| ||||
| OK | |
| 5.CHECK FOR DTC |
Connect the connectors to the occupant classification ECU and the airbag sensor assembly.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Using the Techstream, check for DTCs of the occupant classification ECU (Click here).
|
| ||||
| OK | ||
| ||
| 6.REPLACE OCCUPANT CLASSIFICATION ECU |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Replace the occupant classification ECU (Click here).
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
| NEXT | |
| 7.CHECK FOR DTC |
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Using the Techstream, check for DTCs of the occupant classification ECU (Click here).
|
| ||||
| OK | |
| 8.PERFORM ZERO POINT CALIBRATION AND SENSITIVITY CHECK |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Using the Techstream, perform Zero Point Calibration and Sensitivity Check (Click here).
| NEXT | ||
| ||
| 9.REPLACE AIRBAG SENSOR ASSEMBLY |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Replace the airbag sensor assembly (Click here).
| NEXT | ||
| ||
| 10.CHECK FRONT SEAT WIRE RH |

| *1 | Occupant Classification ECU | *2 | Airbag Sensor Assembly |
| *3 | Front Seat Wire RH | *4 | Floor Wire |
| *5 | Service Wire | - | - |
| *a | Front view of wire harness connector (to Occupant Classification ECU) | *b | Front view of wire harness connector (to Floor Wire) |
| *c | Connector E | *d | Connector D |
Disconnect the front seat wire RH connector from the floor wire.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| JX1-1 - Body ground | Ignition switch ON | Below 1 V |
| JX1-5 - Body ground |
Turn the ignition switch off.
Disconnect the connector from the occupant classification ECU.
Using a service wire, connect terminals 7 and 4 of connector E.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| JX1-1 - JX1-5 | Always | Below 1 Ω |
Disconnect the service wire from connector E.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| JX1-1 - JX1-5 | Always | 1 MΩ or higher |
| JX1-1 - Body ground | ||
| JX1-5 - Body ground |
|
| ||||
| OK | ||
| ||