DTC B1905/74 Short in Front Passenger Side Pretensioner Squib Circuit |
DTC B1906/74 Open in Front Passenger Side Pretensioner Squib Circuit |
DTC B1907/74 Short to GND in Front Passenger Side Pretensioner Squib Circuit |
DTC B1908/74 Short to B+ in Front Passenger Side Front Pretensioner Squib Circuit |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1905/74 |
|
|
| B1906/74 |
|
|
| B1907/74 |
|
|
| B1908/74 |
|
|

| 1.CHECK FRONT SEAT OUTER BELT ASSEMBLY RH (FRONT PASSENGER SIDE FRONT PRETENSIONER SQUIB) |
![]() |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the connectors from the front seat outer belt assembly RH.
Connect the white wire side of SST (resistance 2.1 Ω) to connector C.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch on, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch on, and wait for at least 60 seconds.
Check the DTCs (Click here).
|
| ||||
| NG | |
| 2.CHECK CONNECTOR |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the SST from connector C.
Check that the floor wire connector (on the front seat outer belt assembly RH side) is not damaged.
|
| ||||
| OK | |
| 3.CHECK FLOOR WIRE (FRONT PASSENGER SIDE FRONT PRETENSIONER SQUIB CIRCUIT) |
![]() |
Disconnect the connectors from the center airbag sensor assembly.
Check for short to B+ in the circuit.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch on.
Measure the voltage.
| Tester Connection | Switch Condition | Specified Condition |
| J20-1 (R-) - Body ground | Ignition switch ON | Below 1 V |
| J20-2 (R+) - Body ground | Ignition switch ON | Below 1 V |
Check for open in the circuit.
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| J20-1 (R-) - J20-2 (R+) | Always | Below 1 Ω |
Check for short to ground in the circuit.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| J20-1 (R-) - Body ground | Always | 1 MΩ or higher |
| J20-2 (R+) - Body ground | Always | 1 MΩ or higher |
Check for short in the circuit.
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| J20-1 (R-) - J20-2 (R+) | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 4.CHECK CENTER AIRBAG SENSOR ASSEMBLY |
![]() |
Connect the connectors to the front seat outer belt assembly RH and the center airbag sensor assembly.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch on, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch on, and wait for at least 60 seconds.
Check the DTCs (Click here).
|
| ||||
| OK | ||
| ||