DTC B1655/37 Driver Side Seat Belt Buckle Switch Circuit Malfunction |
| DTC No. | DTC Detecting Condition | Trouble Area |
| B1655/37 |
|
|

| 1.CHECK DTC |
![]() |
Turn the ignition switch on, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch on, and wait for at least 60 seconds.
Check the DTCs (Click here).
|
| ||||
| NG | |
| 2.CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor assembly and the front seat inner belt assembly LH.
|
| ||||
| OK | |
| 3.CHECK FLOOR WIRE (FOR OPEN) |
![]() |
Disconnect the connectors from the center airbag sensor assembly and the front seat inner belt assembly LH.
Using a service wire, connect J8-11 (DBE+) and J8-12 (DBE-) of connector B.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| J10-4 (LBE+) - J10-3 (LBE-) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 4.CHECK FLOOR WIRE (FOR GROUND) |
![]() |
Disconnect the service wire from connector B.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| J10-4 (LBE+) - J10-3 (LBE-) | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 5.CHECK FLOOR WIRE (TO B+) |
![]() |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch on.
Measure the voltage.
| Tester Connection | Switch Condition | Specified Condition |
| J10-4 (LBE+) - Body ground | ignition switch ON | Below 1 V |
| J10-3 (LBE-) - Body ground | ignition switch ON | Below 1 V |
|
| ||||
| OK | |
| 6.CHECK FLOOR WIRE (TO GROUND) |
![]() |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance.
| Tester Connection | Condition | Specified Condition |
| J10-4 (LBE+) - Body ground | Always | 1 MΩ or higher |
| J10-3 (LBE-) - Body ground | Always | 1 MΩ or higher |
|
| ||||
| OK | |
| 7.CHECK FRONT SEAT INNER BELT ASSEMBLY LH |
![]() |
Connect the connector to the center airbag sensor assembly and the front seat inner belt assembly LH.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch on, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch on, and wait for at least 60 seconds.
Check the DTCs (Click here).
|
| ||||
| NG | |
| 8.REPLACE FRONT SEAT INNER BELT ASSEMBLY LH |
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Replace the front seat inner belt assembly LH (Click here).
| NEXT | |
| 9.CHECK CENTER AIRBAG SENSOR ASSEMBLY |
![]() |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch on, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch on, and wait for at least 60 seconds.
Check the DTCs (Click here).
|
| ||||
| OK | ||
| ||