Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER (for Hatchback)

BRAKE BOOSTER (for Hatchback) > INSTALLATION



1. INSTALL BRAKE BOOSTER ASSEMBLY
  1. Install a new gasket onto the brake booster assembly.

  1. Temporarily install the brake booster assembly with the 4 nuts.



    C241860E01
  1. Tighten the 4 nuts in the order shown in the illustration.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Connect the vacuum hose to the vacuum check valve with the clip.



2. INSTALL NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY


    C236725E02
  1. Align the matchmarks on the No. 2 steering intermediate shaft assembly and the steering column assembly and provisionally install them with the bolt.
    Text in Illustration 
    *a
    Matchmark
    *b
    Front of the Vehicle

  1. Tighten the bolt B while aligning the No. 2 steering intermediate shaft assembly with the position C as shown in the illustration.

    Standard C:
    18.5 to 19.7 mm

    Torque:
    35 N*m{ 360 kgf*cm , 26 ft.*lbf }

  1. Tighten bolt A.

    Torque:
    35 N*m{ 360 kgf*cm , 26 ft.*lbf }



3. INSTALL BRAKE MASTER CYLINDER PUSH ROD CLEVIS
  1. Apply lithium soap base glycol grease to the push rod pin.



    C244484
  1. Install the push rod clevis with the push rod pin and a new clip.
    Text in Illustration 
    V100144
    Apply Lithium Soap Base Glycol Grease

  1. Install the brake pedal return spring.



4. INSTALL OUTER COWL TOP PANEL
  1. Install the outer cowl top panel with the 8 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Engage the 2 clamps and install the wire harness.



5. INSTALL INNER COWL TOP TO COWL BRACE
  1. Install the cowl top to cowl brace with the 2 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



6. INSTALL FRONT NO. 1 VENTILATOR SEAL
  1. Engage the clip and install the front No. 1 ventilator seal.



7. INSTALL FRONT AIR SHUTTER SEAL RH

HINT:
Use the same procedure for the RH and LH sides.



8. INSTALL PROPORTIONING VALVE ASSEMBLY (w/o ABS,VSC)
(Click here)


9. INSTALL BRAKE ACTUATOR ASSEMBLY (w/ ABS,VSC)
(Click here)


10. INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY
(Click here)


11. INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY
(Click here)


12. INSPECT AND ADJUST BRAKE PEDAL HEIGHT
(Click here)


13. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL (w/o Knee Airbag)
  1. Engage the 5 claws and 2 clips and install the instrument panel finish panel.



14. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Knee Airbag)
(Click here)


15. INSTALL LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL (w/o Knee Airbag)
  1. Engage the 2 claws and 5 clips and install the instrument panel finish panel.



16. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
  1. Engage the guide and the claw.

  1. Install the instrument panel under cover with the 2 <A> screws.