DTC B1655/37 Driver Side Seat Belt Buckle Switch Circuit Malfunction |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1655/37 |
|
|

| 1.CHECK CONNECTORS |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Check that the connectors are properly connected to the airbag sensor assembly and front seat inner belt assembly LH.
Disconnect the connectors from the airbag sensor assembly and front seat inner belt assembly LH.
Check that the terminals of the connectors are not damaged.
|
| ||||
| OK | |
| 2.CHECK FLOOR WIRE (OPEN) |
Using the service wire, connect terminals 10 (LBE+) and 18 (LBE-) of connector B.

| *1 | Front Seat Inner Belt Assembly LH | *2 | Airbag Sensor Assembly |
| *3 | Floor Wire | *4 | Connector B |
| *5 | Connector C | *6 | Service Wire |
| *a | Front view of wire harness connector (to Airbag Sensor Assembly) | *b | Front view of wire harness connector (to Front Seat Inner Belt Assembly LH) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| J67-2 (LBE+) - J67-1 (LBE-) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 3.CHECK FLOOR WIRE (SHORT) |
![]() |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| J67-2 (LBE+) - J67-1 (LBE-) | Always | 1 MΩ or higher |
| *1 | Front Seat Inner Belt Assembly LH |
| *2 | Airbag Sensor Assembly |
| *3 | Floor Wire |
| *4 | Connector C |
| *a | Front view of wire harness connector (to Front Seat Inner Belt Assembly LH) |
|
| ||||
| OK | |
| 4.CHECK FLOOR WIRE (SHORT TO B+) |
![]() |
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J67-2 (LBE+) - Body ground | Ignition switch ON | Below 1 V |
| J67-1 (LBE-) - Body ground | Ignition switch ON | Below 1 V |
| *1 | Front Seat Inner Belt Assembly LH |
| *2 | Airbag Sensor Assembly |
| *3 | Floor Wire |
| *4 | Connector C |
| *a | Front view of wire harness connector (to Front Seat Inner Belt Assembly LH) |
|
| ||||
| OK | |
| 5.CHECK FLOOR WIRE (SHORT TO GROUND) |
![]() |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| J67-2 (LBE+) - Body ground | Always | 1 MΩ or higher |
| J67-1 (LBE-) - Body ground | Always | 1 MΩ or higher |
| *1 | Front Seat Inner Belt Assembly LH |
| *2 | Airbag Sensor Assembly |
| *3 | Floor Wire |
| *4 | Connector C |
| *a | Front view of wire harness connector (to Front Seat Inner Belt Assembly LH) |
|
| ||||
| OK | |
| 6.CHECK FRONT SEAT INNER BELT ASSEMBLY LH |
Connect the connectors to the airbag sensor assembly and front seat inner belt assembly LH.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 7.REPLACE FRONT SEAT INNER BELT ASSEMBLY LH |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Replace the front seat inner belt assembly LH with a known good one (Click here).
| NEXT | |
| 8.CHECK DTC |
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||