DTC B1660/43 Passenger Airbag ON/OFF Indicator Circuit Malfunction |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1660/43 | When one of following conditions is met:
|
|

| 1.CHECK TELLTALE LIGHT ASSEMBLY (PASSENGER AIRBAG ON/OFF INDICATOR CONDITION) |
Turn the ignition switch to ON.
Check the passenger airbag ON/OFF indicator operation.

| Result | Proceed to |
| Always ON | A |
| OFF | B |
|
| ||||
| A | |
| 2.CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Check that the connectors are properly connected to the airbag sensor assembly and the telltale light assembly.
|
| ||||
| OK | |
| 3.CHECK CONNECTORS |
Disconnect the connectors from the airbag sensor assembly and the telltale light assembly.
Check that the connectors (on the airbag sensor assembly side and telltale light assembly side) are not damaged.
|
| ||||
| OK | |
| 4.CHECK TELLTALE LIGHT ASSEMBLY (PASSENGER AIRBAG ON/OFF INDICATOR) |
![]() |
Connect the connector to the telltale light assembly.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Check the passenger airbag ON/OFF indicator operation.
| *1 | Telltale Light Assembly (Passenger Airbag ON/OFF Indicator) |
|
| ||||
| OK | |
| 5.CHECK DTC |
Connect the connector to the airbag sensor assembly.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 6.CHECK INSTRUMENT PANEL WIRE (AIRBAG SENSOR ASSEMBLY - TELLTALE LIGHT ASSEMBLY) |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Disconnect the connectors from the telltale light assembly and airbag sensor assembly.

| *1 | Telltale Light Assembly (Passenger Airbag ON/OFF Indicator) | *2 | Airbag Sensor Assembly |
| *3 | Instrument Panel Wire | *4 | Connector C |
| *5 | Connector B | *6 | Service Wire |
| *a | Front view of wire harness connector (to Telltale Light Assembly) | *b | Front view of wire harness connector (to Airbag Sensor Assembly) |
Using a service wire, connect terminals 23 (PAON) and 17 (P-AB) of connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D115-2 (PAON) - D115-3 (P-AB) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D115-2 (PAON) - D115-3 (P-AB) | Always | 1 MΩ or higher |
| D115-2 (PAON) - Body ground | Always | 1 MΩ or higher |
| D115-3 (P-AB) - Body ground | Always | 1 MΩ or higher |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D115-2 (PAON) - Body ground | Ignition switch ON | Below 1 V |
| D115-3 (P-AB) - Body ground | Ignition switch ON | Below 1 V |
|
| ||||
| OK | ||
| ||
| 7.CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Check that the connectors are properly connected to the airbag sensor assembly and the telltale light assembly.
|
| ||||
| OK | |
| 8.CHECK CONNECTORS |
Disconnect the connectors from the airbag sensor assembly and the telltale light assembly.
Check that the connectors (on the airbag sensor assembly side and telltale light assembly side) are not damaged.
|
| ||||
| OK | |
| 9.CHECK INSTRUMENT PANEL WIRE (AIRBAG SENSOR ASSEMBLY - TELLTALE LIGHT ASSEMBLY) |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Disconnect the connectors from the telltale light assembly and airbag sensor assembly.

| *1 | Telltale Light Assembly (Passenger Airbag ON/OFF Indicator) | *2 | Airbag Sensor Assembly |
| *3 | Instrument Panel Wire | *4 | Connector C |
| *5 | Connector B | *6 | Service Wire |
| *a | Front view of wire harness connector (to Telltale Light Assembly) | *b | Front view of wire harness connector (to Airbag Sensor Assembly) |
Using a service wire, connect terminals 23 (PAON) and 17 (P-AB) of connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D115-2 (PAON) - D115-3 (P-AB) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D115-2 (PAON) - D115-3 (P-AB) | Always | 1 MΩ or higher |
| D115-2 (PAON) - Body ground | Always | 1 MΩ or higher |
| D115-3 (P-AB) - Body ground | Always | 1 MΩ or higher |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D115-2 (PAON) - Body ground | Ignition switch ON | Below 1 V |
| D115-3 (P-AB) - Body ground | Ignition switch ON | Below 1 V |
|
| ||||
| OK | |
| 10.CHECK TELLTALE LIGHT ASSEMBLY (SOURCE VOLTAGE) |
![]() |
Connect the connectors to the airbag sensor assembly.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D115-8 (LAPB) - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector (to Telltale Light Assembly) |
|
| ||||
| OK | |
| 11.CHECK TELLTALE LIGHT ASSEMBLY (PASSENGER AIRBAG ON/OFF INDICATOR) |
![]() |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Connect the connector to the telltale light assembly.
Disconnect the connectors from the airbag sensor assembly.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Check the indicator according to the value(s) in the table below.
| Tester Connection | Switch Condition | Passenger airbag ON/OFF indicator |
| D112-23 (PAON) - Body ground | Ignition switch ON | "ON" comes on |
| D112-17 (P-AB) - Body ground | Ignition switch ON | "OFF" comes on |
| *a | Front view of wire harness connector (to Airbag Sensor Assembly) |
|
| ||||
| OK | |
| 12.CHECK DTC |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Connect the connectors to the airbag sensor assembly.
Connect the negative (-) terminal cable to the battery and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||