Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM (for Hatchback with VSC)

DTC    B1628/82    Side Airbag Sensor Assembly LH Initialization Incomplete


DESCRIPTION

The side collision sensor LH circuit (to determine deployment of the front seat side airbag assembly LH and curtain shield airbag assembly LH) is composed of the airbag sensor assembly, side airbag sensor LH and No. 2 side airbag sensor assembly LH.
The side airbag sensor assembly LH and No. 2 side airbag sensor assembly LH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbag should be deployed.
This DTC is stored when a malfunction is detected in the side collision sensor LH circuit (to determine deployment of the front seat side airbag assembly LH and curtain shield airbag assembly LH).

DTC No.
DTC Detection Condition
Trouble Area
B1628/82
  1. The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the side collision sensor LH circuit (to determine deployment of the front seat side airbag assembly LH and curtain shield airbag assembly LH).
  2. Side airbag sensor assembly LH malfunction
  3. No. 2 side airbag sensor assembly LH malfunction
  4. Airbag sensor assembly malfunction
  1. Floor wire
  2. Side airbag sensor assembly LH
  3. No. 2 side airbag sensor assembly LH
  4. Airbag sensor assembly

WIRING DIAGRAM


C245265E02


INSPECTION PROCEDURE

1.CHECK HISTORY DTC
  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for history DTCs (Click here).

    Result:
    History DTC B1627/82 is not output.

    HINT:
    Codes other than history DTCs B1627/82 may be output at this time, but they are not related to this check.



NG
INSPECTION PROCEDURE RELEVANT TO OUTPUT DTC (Click here)
OK


2.CHECK CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Check that the connectors are properly connected to the airbag sensor assembly, side airbag sensor assembly LH and No. 2 side airbag sensor assembly LH.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the airbag sensor assembly, side airbag sensor assembly LH and No. 2 side airbag sensor assembly LH.

  1. Check that the terminals of connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE FLOOR WIRE
OK


3.CHECK FLOOR WIRE (OPEN)


  1. Using the service wire, connect terminals 24 (BBL+) and 23 (BBL-) of connector B.


    C241254E04


    Text in Illustration 
    *1
    Side Airbag Sensor Assembly LH
    *2
    Airbag Sensor Assembly
    *3
    Floor Wire
    *4
    Connector B
    *5
    Connector C
    *6
    Service Wire
    *a
    Front view of wire harness connector
    (to Airbag Sensor Assembly)
    *b
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly LH)

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    J73-4 (BBL+) - J73-3 (BBL-)
    Always
    Below 1 Ω



NG
REPLACE FLOOR WIRE
OK


4.CHECK FLOOR WIRE (SHORT)


    C240730E02
  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    J73-4 (BBL+) - J73-3 (BBL-)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Side Airbag Sensor Assembly LH
    *2
    Airbag Sensor Assembly
    *3
    Floor Wire
    *4
    Connector C
    *a
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly LH)



NG
REPLACE FLOOR WIRE
OK


5.CHECK FLOOR WIRE (SHORT TO B+)


    C240730E02
  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    J73-4 (BBL+) - Body ground
    Ignition switch ON
    Below 1 V
    J73-3 (BBL-) - Body ground
    Ignition switch ON
    Below 1 V

    Text in Illustration 
    *1
    Side Airbag Sensor Assembly LH
    *2
    Airbag Sensor Assembly
    *3
    Floor Wire
    *4
    Connector C
    *a
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly LH)



NG
REPLACE FLOOR WIRE
OK


6.CHECK FLOOR WIRE (SHORT TO GROUND)


    C240730E02
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    J73-4 (BBL+) - Body ground
    Always
    1 MΩ or higher
    J73-3 (BBL-) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    Side Airbag Sensor Assembly LH
    *2
    Airbag Sensor Assembly
    *3
    Floor Wire
    *4
    Connector C
    *a
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly LH)



NG
REPLACE FLOOR WIRE
OK


7.CHECK FLOOR WIRE (OPEN)


  1. Using the service wire, connect terminals 4 (BCL+) and 3 (BCL-) of connector C.


    C245278E02


    Text in Illustration 
    *1
    No. 2 Side Airbag Sensor Assembly LH
    *2
    Side Airbag Sensor Assembly LH
    *3
    Floor Wire
    *4
    Connector B
    *5
    Connector C
    *6
    Service Wire
    *a
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly LH)
    *b
    Front view of wire harness connector
    (to No. 2 Side Airbag Sensor Assembly LH)

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    J73-1 (BCL+) - J73-2 (BCL-)
    Always
    Below 1 Ω



NG
REPLACE FLOOR WIRE
OK


8.CHECK FLOOR WIRE (SHORT)


    C240718E05
  1. Disconnect the service wire from connector C.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    J73-1 (BCL+) - J73-2 (BCL-)
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    No. 2 Side Airbag Sensor Assembly LH
    *2
    Side Airbag Sensor Assembly LH
    *3
    Floor Wire
    *4
    Connector B
    *a
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly LH)



NG
REPLACE FLOOR WIRE
OK


9.CHECK FLOOR WIRE (SHORT TO B+)


    C240718E05
  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    J73-1 (BCL+) - Body ground
    Ignition switch ON
    Below 1 V
    J73-2 (BCL-) - Body ground
    Ignition switch ON
    Below 1 V

    Text in Illustration 
    *1
    No. 2 Side Airbag Sensor Assembly LH
    *2
    Side Airbag Sensor Assembly LH
    *3
    Floor Wire
    *4
    Connector B
    *a
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly LH)



NG
REPLACE FLOOR WIRE
OK


10.CHECK FLOOR WIRE (SHORT TO GROUND)


    C240718E05
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    J73-1 (BCL+) - Body ground
    Always
    1 MΩ or higher
    J73-2 (BCL-) - Body ground
    Always
    1 MΩ or higher

    Text in Illustration 
    *1
    No. 2 Side Airbag Sensor Assembly LH
    *2
    Side Airbag Sensor Assembly LH
    *3
    Floor Wire
    *4
    Connector B
    *a
    Front view of wire harness connector
    (to Side Airbag Sensor Assembly LH)



NG
REPLACE FLOOR WIRE
OK


11.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH


    C240729E01
  1. Connect the connectors to the No. 2 side airbag sensor assembly LH and airbag sensor assembly.

  1. Interchange the side airbag sensor assembly LH with the side airbag sensor assembly RH and connect the connectors to them.

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B1628/82 is output.
    A
    DTC B1623/81 is output.
    (for 5 Door)
    B
    DTC B1623/81 is output.
    (for 3 Door)
    C
    DTCs B1623/81 or B1628/82 is not output.
    D
    Text in Illustration 
    *1
    Side Airbag Sensor Assembly RH
    *2
    Airbag Sensor Assembly

    HINT:
    Codes other than DTCs B1623/81 and B1628/82 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Return the side airbag sensor assembly LH and the side airbag sensor assembly RH to their original positions and connect the connectors to them.



B
REPLACE SIDE AIRBAG SENSOR ASSEMBLY LH (Click here)

C
REPLACE SIDE AIRBAG SENSOR ASSEMBLY LH (Click here)

D
USE SIMULATION METHOD TO CHECK (Click here)
A


12.CHECK NO. 2 SIDE AIRBAG SENSOR ASSEMBLY LH


    C166174E16
  1. Interchange the No. 2 side airbag sensor assembly LH with the No. 2 side airbag sensor assembly RH and connect the connectors to them.

  1. Connect the cable to the negative (-) battery terminal.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTCs B1623/81 or B1628/82 is not output.
    A
    DTC B1628/82 is output.
    B
    DTC B1623/81 is output.
    (for 5 Door)
    C
    DTC B1623/81 is output.
    (for 3 Door)
    D
    Text in Illustration 
    *1
    No. 2 Side Airbag Sensor Assembly RH
    *2
    Side Airbag Sensor Assembly LH

    HINT:
    Codes other than DTCs B1623/81 and B1628/82 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Return the No. 2 side airbag sensor assembly LH and the No. 2 side airbag sensor assembly RH to their original positions and connect the connectors to them.



B
REPLACE AIRBAG SENSOR ASSEMBLY (Click here)

C
REPLACE NO. 2 SIDE AIRBAG SENSOR ASSEMBLY LH (Click here)

D
REPLACE NO. 2 SIDE AIRBAG SENSOR ASSEMBLY LH (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)