Home › Engine / Hybrid System › 1NZ-FE ENGINE CONTROL › SFI SYSTEM (for Sedan)

DTC    P2237    Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1)

DTC    P2238    Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 1 Sensor 1)

DTC    P2239    Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 1 Sensor 1)

DTC    P2252    Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 1 Sensor 1)

DTC    P2253    Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 1 Sensor 1)


DESCRIPTION

HINT:
  1. Although the DTC titles say oxygen sensor, these DTCs relate to the Air-Fuel Ratio (A/F) sensor.
  2. Sensor 1 refers to the sensor mounted in front of the Three-Way Catalytic Converter (TWC) and located near the engine assembly.

The A/F sensor, which is located between the exhaust manifold and catalyst, consists of alloyed metal elements and a heater.
Depending on the engine operating conditions, the heater heats the sensor elements to activate them. Battery voltage is applied to the heater, and the sensor ground is controlled by the ECM using a duty ratio.
The sensor elements convert the oxygen concentration in the exhaust gas into voltage values to output. Based on the voltage, the ECM determines the air-fuel ratio and regulates the fuel injection volume depending on the air-fuel ratio and engine operating conditions. The voltage changes between 0.6 V and 4.5 V while the engine is running. If the air-fuel ratio is lean, which means that the oxygen concentration in the exhaust gas is high, the voltage is high. If the air-fuel ratio is rich, which means that the oxygen concentration in the exhaust gas is low, the voltage is low.

A112568E01


A107164E08


DTC No.
DTC Detection Condition
Trouble Area
P2237
Open in the circuit between terminals A1A+ and A1A- of the Air-Fuel Ratio (A/F) sensor while engine is running
(2 trip detection logic)
  1. Open in Air-Fuel Ratio (A/F) sensor (sensor 1) circuit
  2. A/F sensor (sensor 1)
  3. ECM
P2238
  1. Condition (a) or (b) continues for 5.0 seconds or more (2 trip detection logic):
    1. A1A+ voltage is 0.5 V or less.
    2. (A1A+) - (A1A-) is 0.1 V or less.
  1. Open or short in Air-Fuel Ratio (A/F) sensor (sensor 1) circuit
  2. A/F sensor (sensor 1)
  3. ECM
P2239
A1A+ voltage more than 4.5 V
(2 trip detection logic)
  1. Open or short in Air-Fuel Ratio (A/F) sensor (sensor 1) circuit
  2. A/F sensor (sensor 1)
  3. ECM
P2252
A1A- voltage 0.5 V or less
(2 trip detection logic)
  1. Open or short in Air-Fuel Ratio (A/F) sensor (sensor 1) circuit
  2. A/F sensor (sensor 1)
  3. ECM
P2253
A1A- voltage more than 4.5 V
(2 trip detection logic)
  1. Open or short in Air-Fuel Ratio (A/F) sensor (sensor 1) circuit
  2. A/F sensor (sensor 1)
  3. ECM

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on.
  6. Start the engine and wait 5 minutes.
  7. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
  8. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  9. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  10. Input the DTC: P2237, P2238, P2239, P2252 or P2253.
  11. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, idle the engine for 5 minutes and check the DTC judgment result again.


WIRING DIAGRAM

Refer to DTC P0031 .

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
  1. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  2. A low air fuel ratio sensor voltage could be caused by a rich air-fuel mixture. Check for conditions that would cause the engine to run rich.
  3. A high air fuel ratio sensor voltage could be caused by a lean air-fuel mixture. Check for conditions that would cause the engine to run lean.
  4. Sensor 1 refers to the sensor closest to the engine assembly.
  5. Sensor 2 refers to the sensor farthest away from the engine assembly.

1.CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM)
  1. Disconnect the A/F sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    HA1A (C23-1) - HA1A (C20-109)
    Always
    Below 1 Ω
    A1A+ (C23-3) - A1A+ (C20-112)
    Always
    Below 1 Ω
    A1A- (C23-4) - A1A- (C20-113)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    HA1A (C23-1) - HA1A (C20-109) Body ground
    Always
    10 kΩ or higher
    A1A+ (C23-3) - A1A+ (C20-112) Body ground
    Always
    10 kΩ or higher
    A1A- (C23-4) - A1A- (C20-113) Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reconnect the A/F sensor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.REPLACE AIR-FUEL RATIO SENSOR
  1. Replace the A/F sensor (Click here).


NEXT


3.CHECK WHETHER DTC OUTPUT RECURS (DTC P2237, P2238, P2239, P2252 OR P2253)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input the DTC: P2237, P2238, P2239, P2252 or P2253.

  1. Check the DTC judgment.
    Result 
    Result
    Proceed to
    NORMAL (DTC is not output)
    A
    ABNORMAL (DTC P2237, P2238, P2239, P2252 or P2253 is output)
    B



B
REPLACE ECM (Click here)
A

END