DTC B1875/67 Short in Passenger Side Front Seat Cushion Squib Circuit |
DTC B1876/67 Open in Passenger Side Front Seat Cushion Squib Circuit |
DTC B1877/67 Short to GND in Passenger Side Front Seat Cushion Squib Circuit |
DTC B1878/67 Short to B+ in Passenger Side Front Seat Cushion Squib Circuit |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1875/67 |
|
|
| B1876/67 |
| |
| B1877/67 |
| |
| B1878/67 |
|

| 1.CHECK CONNECTORS |
![]() |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connector is properly connected to the SRS seat cushion airbag assembly RH.
Disconnect the connectors from the SRS seat cushion airbag assembly RH and airbag sensor assembly.
Check that the terminal of the connector is not damaged.
Check that the short spring for the floor wire with the activation prevention mechanism is not deformed or damaged.
| *1 | SRS Seat Cushion Airbag Assembly RH |
| *2 | Airbag Sensor Assembly |
| *3 | Floor Wire |
|
| ||||
| OK | |
| 2.CHECK SRS SEAT CUSHION AIRBAG ASSEMBLY RH (SEAT CUSHION SQUIB RH) |
![]() |
Connect the connector to the airbag sensor assembly.
Connect SST (resistance: 2.1 Ω) to connector C.
Connect the cable to the negative battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| *1 | SRS Seat Cushion Airbag Assembly RH |
| *2 | Airbag Sensor Assembly |
| *3 | Connector C |
| *a | Front view of wire harness connector (to SRS Seat Cushion Airbag Assembly RH) |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Disconnect SST from connector C.
|
| ||||
| OK | ||
| ||
| 3.CHECK FLOOR WIRE (SEAT CUSHION SQUIB RH CIRCUIT) |
![]() |
Disconnect the floor wire from the airbag sensor assembly.
Check for a short to B+ in the circuit.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J89-1 (FCP-) - Body ground | Ignition switch ON | Below 1 V |
| J89-2 (FCP+) - Body ground | Ignition switch ON | Below 1 V |
Check for an open in the circuit.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| J89-1 (FCP-) - J89-2 (FCP+) | Always | Below 1 Ω |
Check for a short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| J89-1 (FCP-) - Body ground | Always | 1 MΩ or higher |
| J89-2 (FCP+) - Body ground | Always | 1 MΩ or higher |
Check for a short in the circuit.
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| J89-1 (FCP-) - J89-2 (FCP+) | Always | 1 MΩ or higher |
| *1 | SRS Seat Cushion Airbag Assembly RH |
| *2 | Airbag Sensor Assembly |
| *3 | Floor Wire |
| *4 | Connector C |
| *a | Front view of wire harness connector (to SRS Seat Cushion Airbag Assembly RH) |
Restore the released activation prevention mechanism of connector B to the original condition.
|
| ||||
| OK | |
| 4.CHECK DTC |
![]() |
Connect the connectors to the SRS seat cushion airbag assembly LH and airbag sensor assembly.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| *1 | SRS Seat Cushion Airbag Assembly RH |
| *2 | Airbag Sensor Assembly |
|
| ||||
| OK | ||
| ||